Bush Hog 5045 manual Tractor Ballast, Installation, Hydraulic Hookup

Page 29

5-2 TRACTOR BALLAST

CAUTION

TO HELP PREVENT ROLLOVER, USE REC- OMMENDED REAR TRACTOR BALLAST AND WIDEST WHEEL SETTINGS TO MAXI- MIZE STABILITY. SEE YOUR TRACTOR OPERATOR’S MANUAL FOR RECOMMEN- DATIONS.

Tractor weignt bracket may be left in place on cer- tain tractor models with loader mounted. Front trac- tor weights can only be used when the loader is parked. Weights must be removed before remount- ing loader or serious damage will occur to loader or tractor front axle due to excessive weight.

The use of adequate rear counterweight to counter- balance for maximum loader capacity is required for safe loader operation. Weight added to the rear of the tractor provides better traction and easier, more efficient loader operation.

IMPORTANT

Do not exceed the maximum load capacity of the tires on your tractor. Refer to the Tire and Wheel Specifications in your Tractor Operator’s Manual for more information.

IMPORTANT

This loader has both standard and metric fasten- ers. Verify that the proper fasteners are placed in the correct locations. Do not tighten any bolts firmly until all components are attached onto the tractor.

5-3 INSTALLATION

WARNING

TO AVOID SERIOUS INJURY OR DEATH: READ BEFORE CUTTING BANDS OR REMOVING ATTACHING STRAPS. THE LOADER MAY SHIFT DURING SHIPPING AND HANDLING, MAKING IT UNSTABLE ON THE PALLET. SUPPORT LOADER WITH AN OVERHEAD HOIST OR OTHER SUITABLE MEANS PRIOR TO REMOVING BANDS OR ATTACHING STRAPS SECUR- ING LOADER TO PALLET. FAILURE TO DO SO COULD RESULT IN ACCIDENTAL TIP-OVER OF THE LOADER THAT COULD CAUSE SERIOUS INJURY TO YOU AND/OR BYSTANDERS.

Position the tractor on a hard level surface.

Install mounting brackets on tractor as shown in Installation Instructions included with your Mounting Kit. For ease of handling bracket, insert chain hook into bracket hole. Using hoist, raise and tilt bracket aligning mounting kit holes. Figure 5-1.

Tighten all bolts equally during installation so that outside surface of brackets are level and the center line measurement from right to left hand mounting brackets (Dimension “A”) reads 32” plus or minus 1/4” for the 1045, 37” plus or minus 1/4” for the 2045 or 39” plus or minus 1/4” for the 3045. Figure 5-1.

Figure 5-1

“A”

Bracket Hole

Mounting Bracket

IMPORTANT

To prevent mounting kit hardware from loosen- ing during operation, always torque mounting kit hardware to specified torque noted in Loader Operator’s Manual.

Remove all loader components from shipping pack- aging.

5-4 HYDRAULIC HOOKUP

For use with tractor hydraulic valve, install hoses to loader steel tubing. Install male quick couplers (cus- tomer furnished) to 1/2” male pipe ends of hoses.

Refer to individual instructions that come with the various other valve and control options.

IMPORTANT

When properly installed, the tractor remote valve or external valve control lever/levers will control the loader hydraulic circuits as described in Sections 3-4 - 3-9. Refer to tractor Operator’s Manual for further explanation of tractor remote control lever/levers.

5-5 BUCKET LEVEL INDICATOR ROD

With bucket flat on level surface, fasten “L” end of indicator rod to hole in bucket quick attach with two flat washers and cotter pins as shown in Figure 3-3 on page 15. Install guide bracket over top end of rod as shown. Fasten the bracket to the main frame with 5/16 x 1-1/4” bolt and locknut. Before tightening, ensure that the “kink” in the rod is centered in the bracket slot. This will serve as a visual indication that the bucket is in the level position.

27

Page 28 Page 30
Image 29
Page 28 Page 30
Contents Bush HOG Congratulations 3545 / 4045 / 5045 Table of ContentsDisclaimer of Implied Warranties & Consequential Damages This Limited Warranty Shall not ApplyDealer Preparation Check List Safety Alert Symbol Loader Important Safety PrecautionsTractor Operating the Loader Safety PrecautionsEmployee Tractor Operating Instructions EMPLOYERS, Employees and OperationsIntroduction Section Introduction and DescriptionTechnical Specifications Mounting Loader Section Loader Mounting and DismountingPreparing Tractor Pin In Operating Position 10 Hydraulic Hoses Quick Couplers Dismounting LoaderSection Operating Instructions General SafetyPRE-OPERATION Initial Loader OperationNeutral Position External Loader AND/OR TRAC- TOR ValveFloat Position Regenerative Valve PositionHose Identification Bucket Level Indicator RODRemoving AIR from Hydraulic System Lifting the Load Not this Do this Dump Lower Leverrollback Controlsraise Operating with Float Control Do this Not this Soil Pile Bale Spear OperationTransporting Fork Lift OperationSkid Steer Quick Hitch Operation Maintenance Check List Section MaintenanceHydraulic System Pressure Requirements TroubleshootingTroubleshooting Procedures Problem Possible Cause Remedy Tractor Preparation Section V AssemblyHydraulic Hookup InstallationTractor Ballast Bale Spear Option Fork Lift OptionTine Teeth Side Cutting Edges Optional Bucket Items Assembly Spill Guard AttachmentDigging Teeth American Torque SpecificationsDecals Safety DecalsBush HOG L.L.C Walvoil Valve Mounting Instructions Walvoil Valve Mounting Instructions Valve Stand Assembly Instructions Single Handle Valve KIT Attaching Handle MOUNT, Control Handle Cables to Tractor Support Mount to Front of Tractor Attaching Valve to Loader Frame Connecting Hydraulics Refer to and Fig Adjust the cables so the control handle operates as follows Cable Control Valve KIT Installation Instructions For 24H46343 Power Beyond KIT Cable Control Walvoil Valve Assembly Standard Walvoil Valve Assembly Sept Instruction Sheet No H46344 ~ Assembly Instructions ~ Page Front Description Bush HOG Bush HOG 24H49871 Grapple Attachment
Related manuals
Manual 1 pages 38.86 Kb

5045 specifications

The Bush Hog 5045 represents a versatile and robust solution for agricultural needs, particularly for those requiring a reliable utility vehicle. This machine stands out for its combination of power, efficiency, and ease of use. Tailored for farm operations, landscaping tasks, and various outdoor chores, the 5045 has earned a reputation for its dependability and performance.

One of the main features of the Bush Hog 5045 is its powerful engine. Equipped with a reliable diesel engine, this model delivers excellent torque and performance, ensuring it can handle challenging terrains and tough workloads. The engine is designed for fuel efficiency, enabling users to maximize productivity while minimizing operating costs.

In terms of technology, the Bush Hog 5045 incorporates advanced hydraulic systems. The hydraulic capabilities enhance its versatility, allowing operators to attach a variety of implements like loaders, blades, and even backhoes. This adaptability makes it an invaluable asset on the farm or job site, as it can seamlessly switch between different tasks.

The 5045 also boasts a spacious operator platform with a comfortable seat and user-friendly controls. This ergonomic design not only ensures comfort during long working hours but also enhances safety and accessibility. The visibility from the operator's seat is excellent, allowing for better awareness of surroundings and improving overall operational safety.

Storage options are another noteworthy characteristic. The Bush Hog 5045 includes ample storage compartments for tools and other necessities, ensuring that operators have everything they need on hand while minimizing trips back to the workshop or garage.

Durability is a hallmark of the Bush Hog brand, and the 5045 is no exception. Built with high-quality materials, this utility vehicle withstands the rigors of daily use, ensuring longevity and reducing maintenance needs. The heavy-duty frame and robust components contribute to its ability to tackle tough tasks year after year.

Overall, the Bush Hog 5045 is a practical, durable, and efficient utility vehicle suited for a variety of applications. Whether it’s for farming, landscaping, or general maintenance, this model combines power with usability to meet the demands of modern agricultural operations. With its blend of features, technology, and robust construction, the Bush Hog 5045 continues to be a preferred choice among professionals in the field.
Top Page Image Contents