Briggs & Stratton NSPVH21675 specifications Cutting Height Adjustment, Recycling Operation

Page 9

!

WARNING

!

DO NOT attempt any maintenance, adjustments or service with engine and blade running. STOP engine and blade. Disconnect spark plug wire and secure away from spark plug. Engine and components are HOT. Avoid serious burns, allow sufficient time for all components to cool.

Cutting Height Adjustment

1.Pull the height adjusting lever (A, Figure 6) outward, and move to the desired cutting height. The highest cutting position is Notch 9 (B; also see Figure 7). The lowest cutting position is Notch 1 (C).

Note: The lever will set all wheels to the same cutting height.

!

WARNING

!

Stop engine and mower blade by releasing the blade control before adjusting cutting height.

A

C

B

Figure 6: Adjusting cutting height

1.50 in 4.00 in

Figure 7: Cutting height settings (approximate)

Recycling Operation

Note: For best recycling results, cut up to a maximum of 1/3 of grass blade length and recycle ONLY when grass is dry.

1.Set the height adjustment lever in the highest cutting position (Notch 9). Refer to the Section entitled “Cutting Height Adjustment”.

2.Proceed mowing slowly. If the grass is very dense, lower the height adjustment lever one notch lower to improve recycling performance.

Installing the Discharge Deflector

1. Raise the recycling cover (A, Figure 8).

Important: The recycling cover should remain on the machine at all times. Do not remove.

A

D

C

B

Figure 8: Installing the discharge deflector

2.Install the deflector (B) to the deck under the recycling cover, making sure that:

The tabs (C) hook under the pivot rod (D). The locking tab on the deck (A, Figure 9) goes through the slot in the deflector (B).

3.Lower the recycling cover against the deflector.

Operation

7

Page 8 Page 10
Image 9
Page 8 Page 10
Contents Variable Speed Rear Discharge Walk Behind Mowers Product Registration Date of Purchase Retailer Retailers Phone Number EquipmentEngine Table of Contents Slope Operation Protection for ChildrenPreparation From Previous ColumnOperation Maintenance and StorageFeatures and Controls Pre-Start Check List Starting and OperationEngine and Blade Handle Height Adjustment StoppingPropelling the Mower Cutting Height Adjustment Installing the Discharge DeflectorRecycling Operation Removing the Recycling Plug Installing the Grass BagMaintenance Introduction Service After First 5 HoursService Periodic Wheel Drive Components Storage ProcedureMower Blade Replacement Standard Blade Wear LimitBlade Sharpening Wheel drive controls Wheel Drive Control AdjustmentEngine Drive Belt Replacement Belt ServiceRear Cover Removal and Installation To Install the Rear CoverTo Remove the Rear Cover Season Service ScheduleProbable Cause Corrective Action TroubleshootingDisclaimer of Warranty Year Limited WarrantyPage Slope Guide Page Page Part Number Product Specifications All Common Service Parts

SPVH21675, NSPVH21675 specifications

Briggs & Stratton NSPVH21675 and SPVH21675 are advanced vertical shaft engines designed to deliver reliable power for various outdoor equipment. Known for their durability and performance, these engines are ideal for lawn mowers, pressure washers, and other gardening tools, making them a popular choice among both residential and commercial users.

One of the standout features of the NSPVH21675 and SPVH21675 is their robust construction, which includes a cast-iron cylinder sleeve that enhances strength and prolongs engine life. This ensures that these engines can withstand the rigors of tough outdoor tasks while maintaining optimal performance. The design is further complemented by an aluminum crankcase that contributes to reduced weight without sacrificing durability.

Another key aspect of these engines is the innovative Direct Inject Technology. This advanced fuel management system allows for improved fuel efficiency by optimizing the air-fuel mixture delivered to the combustion chamber. As a result, users can expect enhanced power output while consuming less fuel, making these engines an eco-friendlier option.

The NSPVH21675 and SPVH21675 also feature a unique intake and exhaust system that maximizes airflow. This design not only enhances engine performance but also contributes to quieter operation. Operators will appreciate the reduced noise levels, making their time spent working outdoors more pleasant.

In terms of maintenance, Briggs & Stratton has engineered these models with user-friendly accessibility in mind. Routine checks and maintenance tasks are straightforward, allowing operators to spend more time on their projects rather than on upkeep. The engines are also equipped with an oil alert system, which helps prevent issues related to low oil levels, promoting longevity and reliability.

Both engines are designed with versatility in mind, able to power a range of equipment with different requirements. This adaptability is further exemplified by their electric start option, which simplifies the starting process and is particularly beneficial for larger machines that may require more effort to start.

Overall, the Briggs & Stratton NSPVH21675 and SPVH21675 engines represent a blend of power, efficiency, and ease of use. With their innovative technologies, robust construction, and user-friendly designs, they are a top choice for anyone in need of reliable outdoor power equipment solutions. Whether for personal use or professional landscaping, these engines provide the performance and durability to get the job done efficiently and effectively.
Top Page Image Contents