Briggs & Stratton 5900670 Battery Maintenance, Cleaning the Battery and Cables Air Cooled Models

Page 34

Maintenance

Regular Maintenance

BATTERY MAINTENANCE

NOTE: This unit is equipped with a maintenance-free BCIU1 battery.

Cleaning the Battery and Cables - Air Cooled Models.

1.Remove the hydraulic oil reservoir mounting hardware (C, Figure 24) and move the reservoir

(D) forward to expose the battery.

2.Disconnect the cables from the battery, negative (black) cable first (B).

3.Clean the battery terminals and cable ends with a wire brush until shiny.

4.Reinstall the battery and reattach the battery cables, positive (red) cable first (A).

5.Coat the cable ends and battery terminals with petroleum jelly or non-conducting grease.

6.Reposition the oil reservoir and secure in place with the hardware previously removed.

WARNING

Be careful when handling the battery. Avoid spilling electrolyte. Keep flames and sparks away from the battery.

When removing or installing battery cables, disconnect the negative cable FIRST and reconnect it LAST. If not done in this order, the positive terminal can be shorted to the frame by a tool.

Cleaning the Battery and Cables - Liquid Cooled Models.

1.Raise the seat plate to expose the battery.

2.Disconnect the cables from the battery, negative (black) cable first (B).

3.Clean the battery terminals and cable ends with a wire brush until shiny.

4.Reinstall the battery and reattach the battery cables, positive (red) cable first (A).

5.Coat the cable ends and battery terminals with petroleum jelly or non-conducting grease.

6.Reposition the oil reservoir and secure in place with the hardware previously removed.

D	Air Cooled
	Models
	C
	A
C
B
	Liquid Cooled
	Models
	A
B

Figure 24. Battery Compartment

A.Positive (+) Cable & Terminal

B.Negative (-) Cable & Terminal

C.Reservoir Mounting Hardware

D.Hydraulic Oil Reservoir

32	www.ferrisindustries.com

Image 34

Contents Description Briggs & Stratton Yard Power Products GroupModel Number Date Purchased Table of Contents Operating Safety Slope Operation Roll Bar Use Fuel and Maintenance Training OperationPreparation Children Slope OperationTowed Equipment RIDE-ON Units EmissionsMaintenance and Storage Service and MaintenanceSafe Handling of Gasoline Roll BAR Instructions Operational WarningsInspection and Maintenance of the Roll BAR Seat Belt Identification Numbers IdentificationSafety Decals North American Safety Icons Safety Interlock SystemOperational Safety Checks AIR Cooled Models only Seat Adjustment LeverIgnition Switch Control FunctionsParking Brake PTO Power Take Off SwitchHour Meter / Maintenance Reminder Throttle ControlLiquid Cooled Models only Water Temperature Gauge Checks Before Starting General Operating SafetyNever allow passengers to ride on the unit Stopping the Rider Starting the EnginePushing the Rider by Hand Forward Travel Practice Zero Turn Driving PracticeSmooth Travel Reverse Travel PracticeExecuting Turns Practice Turning Around a Corner Practice Turning In PlaceExecuting an End-Of-Row Zero Turn TurningHeight of Grass MowingMowing Recommendations Tall Grass Requires Incremental CuttingMowing Patterns When and How Often to MowMowing Methods Proper Broadcast MowingAttaching a Trailer Proper MulchingTo raise the roll bar Raise & Lower the Roll BARTo lower the roll bar Keep roll bar in the raised position and use seat beltTemporary Storage 30 Days Or Less StorageStarting After Long Term Storage Long Term Storage Longer Than 30 DaysEngine Maintenance Safety ItemsRider Maintenance Before Every Spring Each 100 250 Fall Use HoursFuel Filter Check Tire PressuresChecking / Adding Fuel Change OIL & FilterAir Cooled Models Check Hydraulic OIL LevelChange Hydraulic OIL Filter Liquid Cooled ModelsCheck Engine Coolant Level Change Engine Coolant Clean Radiator & ScreenPressurized System Oil LubricationGrease PivotsCleaning the Battery and Cables Air Cooled Models Battery MaintenanceCleaning the Battery and Cables Liquid Cooled Models Servicing the Mower Blades Removing the BladeTroubleshooting Warning Troubleshooting the RiderTroubleshooting the Mower Rider TroubleshootingTroubleshooting Common Cutting Problems StreakingGround Speed Control Lever Adjustment Seat AdjustmentSpeed Balancing Adjustment Adjustment Linkage Rod Neutral AdjustmentRETURN-TO-NEUTRAL Adjustment RH side shownParking Brake Adjustment Parking Brake Adjustment Brake Spring Adjustment NutTo adjust the spring pre-load Suspension AdjustmentTo adjust the upper mounting position Foot Pedal Adjustment Mowing Height AdjustmentTo adjust pedal position Inner Rod Deck Lift ROD Timing AdjustmentOuter Rod Deck Lift Spring Deck Leveling Adjustment4 Locations Hydraulic Pump Drive Belt Replacement Mower Belt Replacement DeckCharging a Completely Discharged Battery Battery ServiceChecking Battery Voltage Jump Starting With Auxiliary Booster BatteryMake Certain Vehicles do not Touch This HOOK-UP for Negative Ground VehiclesJump Starting Chassis DimensionsEngine TransmissionsFerris Limited Warranty Tractor Belts and BladesHP Briggs & Stratton Mower Deck