Briggs & Stratton 5901170, 5900625 manual Check Tire Pressures, Checking / Adding Fuel, Fuel Filter

Page 30

Maintenance

Regular Maintenance

CHECK TIRE PRESSURES

Tire pressure should be checked periodically, and maintained at the levels shown in the chart. Note that these pressures may differ slightly from the “Max Inflation” stamped on the side-wall of the tires. The pressures shown provide proper traction, improve cut quality, and extend tire life.

Tire

Pressure

Front

25 psi (1,72 bar)

 

 

Rear

15 psi (1,03 bar)

 

 

CHECKING / ADDING FUEL

To add fuel:

1.Remove the fuel cap (see Figure 1).

2.Fill the tank to the bottom of the filler neck. This will allow for fuel expansion.

NOTE: Do not overfill. Refer to your engine manual for specific fuel recommendations.

3. Install and hand tighten the fuel cap.

FUEL FILTER

The fuel filter is located in the fuel line between fuel tank and carburetor, near the fuel pump. If filter is dirty or clogged, replace as follows:

1.Disconnect the negative battery cable.

2.Place a container below the filter to catch spilled fuel.

3.Using a pliers, open and slide hose clamps from fuel filter.

4.Remove hoses from filter.

5.Install new filter in proper flow direction in fuel line.

6.Secure with hose clamps.

7.Reconnect the negative battery cable when finished.

CHANGE OIL & FILTER

1.Warm engine by running for a few minutes. (Refer to the engine operator’s manual for oil & filter replacement instructions.)

2.Remove the oil drain hose (A, Figure 15) from the cable clamp (B) on the right-hand side of the frame and route the hose through hole in the engine deck as shown in Figure 15.

3.Place a small pan under the oil drain hose to catch the oil. Using the appropriate tools, remove the cap from the oil drain hose (A) and drain the engine oil.

4.After draining, replace the cap and wipe up any spilled oil. Reinstall the oil drain hose into the cable clamp to retain the hose during normal operation.

5.Place an absorbent shop cloth under the engine oil filter. Remove the engine oil filter and replace with a new one.

6.Remove the shop cloth and wipe up any spilled oil.

Figure 14. Checking Tire Pressure

WARNING

Gasoline is highly flammable and must be handled with care. Never fill the tank when the engine is still hot from recent operation. Do not allow open flame, smoking or matches in the area. Avoid over-filling and wipe up any spills.

Do not remove fuel filter when engine is hot, as spilled gasoline may ignite. DO NOT spread hose clamps further than necessary. Ensure clamps grip hoses firmly over filter after installation.

Do not use gasoline containing METHANOL, gasohol containing more than 10% ethanol, gasoline additives, premium gasoline, or white gas because engine/fuel system damage could result.

B

A

Figure 15. Engine Oil Drain

A.Oil Drain Hose

B.Cable Clamp

28

www.ferrisindustries.com

Page 29 Page 31
Image 30
Page 29 Page 31
Contents Briggs & Stratton Yard Power Products Group DescriptionModel Number Date Purchased Table of Contents Operating Safety Slope Operation Roll Bar Use Fuel and Maintenance Operation TrainingPreparation Children Slope OperationTowed Equipment RIDE-ON Units EmissionsService and Maintenance Maintenance and StorageSafe Handling of Gasoline Roll BAR Instructions Operational WarningsInspection and Maintenance of the Roll BAR Seat Belt Identification Numbers IdentificationSafety Decals Safety Interlock System North American Safety IconsOperational Safety Checks AIR Cooled Models only Seat Adjustment LeverIgnition Switch Control FunctionsParking Brake PTO Power Take Off SwitchHour Meter / Maintenance Reminder Throttle ControlLiquid Cooled Models only Water Temperature Gauge General Operating Safety Checks Before StartingNever allow passengers to ride on the unit Starting the Engine Stopping the RiderPushing the Rider by Hand Forward Travel Practice Zero Turn Driving PracticeSmooth Travel Reverse Travel PracticeExecuting Turns Practice Turning Around a Corner Practice Turning In PlaceExecuting an End-Of-Row Zero Turn TurningHeight of Grass MowingMowing Recommendations Tall Grass Requires Incremental CuttingMowing Patterns When and How Often to MowMowing Methods Proper Broadcast MowingAttaching a Trailer Proper MulchingTo raise the roll bar Raise & Lower the Roll BARTo lower the roll bar Keep roll bar in the raised position and use seat beltTemporary Storage 30 Days Or Less StorageStarting After Long Term Storage Long Term Storage Longer Than 30 DaysEngine Maintenance Safety ItemsRider Maintenance Before Every Spring Each 100 250 Fall Use HoursFuel Filter Check Tire PressuresChecking / Adding Fuel Change OIL & FilterAir Cooled Models Check Hydraulic OIL LevelChange Hydraulic OIL Filter Liquid Cooled ModelsChange Engine Coolant Clean Radiator & Screen Check Engine Coolant LevelPressurized System Oil LubricationGrease PivotsBattery Maintenance Cleaning the Battery and Cables Air Cooled ModelsCleaning the Battery and Cables Liquid Cooled Models Servicing the Mower Blades Removing the BladeTroubleshooting Warning Troubleshooting the RiderTroubleshooting the Mower Rider TroubleshootingTroubleshooting Common Cutting Problems StreakingSeat Adjustment Ground Speed Control Lever AdjustmentSpeed Balancing Adjustment Adjustment Linkage Rod Neutral AdjustmentRETURN-TO-NEUTRAL Adjustment RH side shownParking Brake Adjustment Parking Brake Adjustment Brake Spring Adjustment NutSuspension Adjustment To adjust the spring pre-loadTo adjust the upper mounting position Mowing Height Adjustment Foot Pedal AdjustmentTo adjust pedal position Deck Lift ROD Timing Adjustment Inner RodOuter Rod Deck Leveling Adjustment Deck Lift Spring4 Locations Hydraulic Pump Drive Belt Replacement Mower Belt Replacement DeckCharging a Completely Discharged Battery Battery ServiceChecking Battery Voltage Jump Starting With Auxiliary Booster BatteryThis HOOK-UP for Negative Ground Vehicles Make Certain Vehicles do not TouchJump Starting Chassis DimensionsEngine TransmissionsFerris Limited Warranty Tractor Belts and BladesHP Briggs & Stratton Mower Deck
Top Page Image Contents