Briggs & Stratton 5900619 manual PTO Power Take Off Switch, Glow Plug Indicator, Throttle Control

Page 18

Features & Controls

PTO (Power Take Off) Switch

The PTO switch engages and disengages the mower. Pull UP on the switch to engage the mower, and push DOWN to disengage the mower.

Glow Plug Indicator

Lamp that indicates that the glow plugs are heating. Hold the ignition key in the “HEAT” position until indicator lamp turns off, then turn the key to start.

Controls

Throttle Control

Moving the throttle control fully forward is FULL throttle position. Always operate the unit at FULL throttle when mowing.

Parking Brake

 

 

 

DISENGAGE

Releases the parking brake.

 

 

 

 

 

 

 

 

 

ENGAGE

Locks the parking brake.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Pull the parking brake lever back to engage the parking brake. Move the lever fully forward to disengage the parking brake. NOTE: To start the unit the parking brake must be engaged.

Deck Lift Pedal, Cutting

Height Adjustment Pin & Deck Lift Lock

Lever

These control the cutting height of the mower deck. Depress the pedal until it locks into the 6” (15,2 cm) position. Place the adjustment pin in the desired cutting height and release the lift lock lever.

Hour Meter / Maintenance Reminder

Measures the time of the PTO being engaged. The hour meter measures the number of hours the PTO has been engaged. The hour meter will flash an initial oil change indicator at 5 hours, and a lubrication reminder every 50 hours. These reminders display for approximately two hours and will automatically reset themselves.

Note: The hour meter will register the passage of time only when the PTO is engaged. The hour meter has a self contained power source so the total hours are always visible.

Voltage Gauge

Gauge measures the output voltage of the engine charging system.

Oil Pressure Indicator

Lamp that indicates a low oil pressure condition. If the indicator lamp is ON, it will turn the PTO OFF.

Water Temperature Gauge & Indicator

Gauge measures the engine coolant temperature. Lamp that indicates a high coolant temperature. If the indicator lamp is ON, it will turn the PTO OFF.

Fuel Tank Cap

To remove the cap, turn counterclockwise.

Fuel Level Gauge

Displays the fuel level in the tank.

Power Outlet

Unit is equipped with a +12VDC, 20A power outlet.

16

www.ferrisindustries.com

Page 17 Page 19
Image 18
Page 17 Page 19
Contents Manual Date Purchased Table of Contents Operating Safety Slope Operation Roll Bar Use Fuel and Maintenance Operation Slope Operation Service and Maintenance Roll BAR Instructions Inspection and Maintenance of the Roll BAR Seat Belt CE Identification TAG Markings Safety Decals Safety DecalsNorth American Models CE Models Export Safety Icons Safety Interlock System Safety Interlock SystemOperational Safety Checks Ignition Switch Features & ControlsSeat Adjustment Lever Ground Speed LeversHour Meter / Maintenance Reminder PTO Power Take Off SwitchGlow Plug Indicator Oil Pressure IndicatorGeneral Operating Safety OperationChecks Before Starting On the water separator Priming the Fuel SystemTo prime the fuel system On the engine fuel filterStarting the Engine Stopping the Tractor & EngineDriving the Tractor Pushing the Rider by Hand Do not TOW RiderForward Travel Practice Zero Turn Driving PracticeSmooth Travel Reverse Travel PracticeExecuting an End-Of-Row Zero Turn Practice Turning Around a CornerPractice Turning In Place Executing TurnsHeight of Grass MowingMowing Recommendations Tall Grass Requires Incremental CuttingMowing Patterns When and How Often to MowMowing Methods Proper Broadcast MowingAttaching a Trailer Proper MulchingTo raise the roll bar Raise & Lower the Roll BARTo lower the roll bar Keep roll bar in the raised position and use seat beltDiesel Fuel Recommendations StorageStarting After Long Term Storage Temporary Storage 30 Days Or LessCheck Tire Pressures Regular MaintenanceMaintenance Schedule & Procedures Before Every Spring Each 100 250 Fall Use HoursChecking / Adding Fuel Fuel FilterTo add fuel Hydraulic OIL Filter Change Check / ADD Engine OILCheck / Change AIR Filter Check Hydraulic OIL Level Change Interval Every 500 Hours Filter Part NumberRadiator Pressure Cap Change Engine Coolant Clean RADIATOR, Screen & OIL CoolerCheck Engine Coolant Level Radiator ScreenLubrication Grease OilBattery Maintenance Cleaning the Battery and CablesANTI-SCALP Deck Casters Servicing the Mower Blades Removing the BladeTroubleshooting, Adjustments & Service Troubleshooting WarningTroubleshooting the Rider Troubleshooting, Adjustment & Service Rider TroubleshootingTroubleshooting the Mower Troubleshooting Common Cutting Problems StreakingSeat Adjustment Ground Speed Lever AdjustmentSpeed Balancing Adjustment Neutral Position Adjustment Neutral AdjustmentNeutral Position and Return Spring Adjustment Return Spring AdjustmentParking Brake Adjustment 1/85,4cm To discover how many shims are needed Rear Tire Camber AdjustmentInstalling the camber shims Distance Measured Number of ShimsUse two hands when adjusting the shock Suspension AdjustmentTo adjust the spring pre-load Springs. This will prevent the wrench fromMowing Height Adjustment Deck Lift ROD Timing Adjustment Inner RodOuter Rod Deck Leveling Adjustment Deck Lift SpringBelt Removal & Replacement Mower Drive Belt Removal ReplacementSide Discharge Model Models Rear Discharge Models Clutch Belt Replacement Clutch Belt RemovalPump Drive Belt Replacement Pump Drive Belt RemovalChanging Gearbox Oil Gearbox MaintenanceCheck Gearbox Oil Level FrontBattery Service Checking Battery VoltageTroubleshooting, Adjustment & Service Jump StartingEngine SpecificationsDimensions ChassisFerris Limited Warranty OPERATOR’S Manual

5900619 specifications

The Briggs & Stratton 5900619 is a highly regarded replacement engine part designed specifically for a range of lawn and garden equipment, ensuring optimal performance and reliability. Known for its durability and innovation, this part caters to those who require dependable machinery for their outdoor tasks.

One of the key features of the Briggs & Stratton 5900619 is its compatibility with a variety of mower models, making it a versatile choice for both amateur and professional landscapers. This adaptability not only streamlines the maintenance process but also reduces downtime, allowing users to focus on their landscaping tasks rather than equipment issues.

The construction of the Briggs & Stratton 5900619 highlights the brand's commitment to quality. Made from robust materials, this replacement part is designed to withstand harsh outdoor conditions. This ruggedness ensures that it can handle the wear and tear often associated with regular use in challenging environments, contributing to a longer lifespan for both the engine and the machinery it services.

In terms of technology, the Briggs & Stratton 5900619 incorporates advanced engineering principles that enhance its reliability and efficiency. This includes features that promote fuel efficiency, helping users to save on operating costs. By delivering optimal power output while minimizing fuel consumption, this engine part exemplifies the brand's drive towards sustainability and economical operation.

Moreover, the Briggs & Stratton 5900619 is designed for ease of installation. With clear specifications and user-friendly guidelines, it allows both DIY enthusiasts and professionals to replace parts without extensive technical knowledge. This feature is particularly beneficial for those who value efficiency in their maintenance routines.

Another important characteristic of the 5900619 is its performance consistency. Users can expect reliable starts and steady operation, which is critical when tackling large areas of lawn or garden spaces. The engine’s design includes features that help maintain stable power flow, reducing the chances of stalling or unexpected performance issues.

In summary, the Briggs & Stratton 5900619 is a standout choice for anyone looking to enhance their lawn care equipment. With its compatibility across various mower models, durability, advanced technology, ease of installation, and consistent performance, it represents a significant investment in maintaining the health and efficiency of outdoor machinery. This engine part is not just a replacement—it’s a commitment to better gardening outcomes.
Top Page Image Contents