Briggs & Stratton 5900619 manual Check / ADD Engine OIL, Hydraulic OIL Filter Change

Page 32

Maintenance

Regular Maintenance

CHECK / ADD ENGINE OIL

Refer to Figure 15 for dipstick and oil fill locations.

Refer to the engine owners manual for specific engine oil check and fill procedures. Also refer to the engine owners manual for specific engine oil and filter change procedures.

CHECK / CHANGE AIR FILTER

Refer to the engine owners manual for specific air filter service procedures.

CHECK HYDRAULIC OIL LEVEL

NOTE: Do not open the hydraulic oil reservoir unless oil is being added.

1.Visually check that the hydraulic oil level is filled to the recess area (A, Figure 16) of the hydraulic oil reservoir.

2.If necessary, remove the reservoir cap (B) and add either Mobil 1™, 15W-50 synthetic oil or Castrol Syntec™ 5W-50 oil. DO NOT use conventional oils. Make sure area around the filler neck is free of dust, dirt, or other debris.

HYDRAULIC OIL FILTER CHANGE

Change Interval: Every 500 Hours

Filter Part Number: 5021357

NOTE: Removing the oil filter from the filter base will drain the oil reservoir. Have a suitable container ready to catch any spilled oil. Ferris recommends this be a dealer-only service item.

1.Locate the hydraulic oil filter (A, Figure 17) behind the battery.

2.Fill the new filter with oil. Lubricate the new filter seal with a few drops of oil.

3.Remove the oil filter and quickly thread the new filter onto the filter base until the gasket makes contact, then tighten 3/4 of a turn more.

4.Refill reservoir with fresh oil to replace any oil lost during filter change.

5.Raise the rear of the unit and secure with jackstands. Chock the front wheels to prevent the unit from rolling. Run the unit for several minutes to purge any air from the hydraulic system and check the hydraulic oil level.

IMPORTANT NOTE: Use caution after changing the filter; air in the hydraulic system may affect the responsiveness of the control levers. Repeat step 5 until the air is out of the system.

A

B

Figure 15. Change Oil & Filter

A.Oil Fill Cap

B.Crankcase Dip Stick

A

B

Figure 16. Hydraulic Oil Reservoir

A.Tank Recess (“FULL” level)

B.Cap

A

B

Figure 17. Hydraulic Oil Filter Location

A.Oil Filter

B.Battery

30

www.ferrisindustries.com

Page 31 Page 33
Image 32
Page 31 Page 33
Contents Manual Date Purchased Table of Contents Operating Safety Slope Operation Roll Bar Use Fuel and Maintenance Operation Slope Operation Service and Maintenance Roll BAR Instructions Inspection and Maintenance of the Roll BAR Seat Belt CE Identification TAG Markings North American Models CE Models Export Safety DecalsSafety Decals Safety Icons Operational Safety Checks Safety Interlock SystemSafety Interlock System Features & Controls Seat Adjustment LeverIgnition Switch Ground Speed LeversPTO Power Take Off Switch Glow Plug IndicatorHour Meter / Maintenance Reminder Oil Pressure IndicatorChecks Before Starting General Operating SafetyOperation Priming the Fuel System To prime the fuel systemOn the water separator On the engine fuel filterDriving the Tractor Starting the EngineStopping the Tractor & Engine Pushing the Rider by Hand Do not TOW RiderZero Turn Driving Practice Smooth TravelForward Travel Practice Reverse Travel PracticePractice Turning Around a Corner Practice Turning In PlaceExecuting an End-Of-Row Zero Turn Executing TurnsMowing Mowing RecommendationsHeight of Grass Tall Grass Requires Incremental CuttingWhen and How Often to Mow Mowing MethodsMowing Patterns Proper Broadcast MowingAttaching a Trailer Proper MulchingRaise & Lower the Roll BAR To lower the roll barTo raise the roll bar Keep roll bar in the raised position and use seat beltStorage Starting After Long Term StorageDiesel Fuel Recommendations Temporary Storage 30 Days Or LessRegular Maintenance Maintenance Schedule & ProceduresCheck Tire Pressures Before Every Spring Each 100 250 Fall Use HoursTo add fuel Checking / Adding FuelFuel Filter Check / ADD Engine OIL Check / Change AIR Filter Check Hydraulic OIL LevelHydraulic OIL Filter Change Change Interval Every 500 Hours Filter Part NumberChange Engine Coolant Clean RADIATOR, Screen & OIL Cooler Check Engine Coolant LevelRadiator Pressure Cap Radiator ScreenLubrication Grease OilANTI-SCALP Deck Casters Battery MaintenanceCleaning the Battery and Cables Servicing the Mower Blades Removing the BladeTroubleshooting the Rider Troubleshooting, Adjustments & ServiceTroubleshooting Warning Troubleshooting the Mower Troubleshooting, Adjustment & ServiceRider Troubleshooting Troubleshooting Common Cutting Problems StreakingSpeed Balancing Adjustment Seat AdjustmentGround Speed Lever Adjustment Neutral Adjustment Neutral Position and Return Spring AdjustmentNeutral Position Adjustment Return Spring Adjustment5,4cm Parking Brake Adjustment1/8 Rear Tire Camber Adjustment Installing the camber shimsTo discover how many shims are needed Distance Measured Number of ShimsSuspension Adjustment To adjust the spring pre-loadUse two hands when adjusting the shock Springs. This will prevent the wrench fromMowing Height Adjustment Outer Rod Deck Lift ROD Timing AdjustmentInner Rod Deck Leveling Adjustment Deck Lift SpringSide Discharge Model Models Rear Discharge Models Belt Removal & ReplacementMower Drive Belt Removal Replacement Clutch Belt Replacement Clutch Belt RemovalPump Drive Belt Replacement Pump Drive Belt RemovalGearbox Maintenance Check Gearbox Oil LevelChanging Gearbox Oil FrontBattery Service Checking Battery VoltageTroubleshooting, Adjustment & Service Jump StartingSpecifications DimensionsEngine ChassisFerris Limited Warranty OPERATOR’S Manual

5900619 specifications

The Briggs & Stratton 5900619 is a highly regarded replacement engine part designed specifically for a range of lawn and garden equipment, ensuring optimal performance and reliability. Known for its durability and innovation, this part caters to those who require dependable machinery for their outdoor tasks.

One of the key features of the Briggs & Stratton 5900619 is its compatibility with a variety of mower models, making it a versatile choice for both amateur and professional landscapers. This adaptability not only streamlines the maintenance process but also reduces downtime, allowing users to focus on their landscaping tasks rather than equipment issues.

The construction of the Briggs & Stratton 5900619 highlights the brand's commitment to quality. Made from robust materials, this replacement part is designed to withstand harsh outdoor conditions. This ruggedness ensures that it can handle the wear and tear often associated with regular use in challenging environments, contributing to a longer lifespan for both the engine and the machinery it services.

In terms of technology, the Briggs & Stratton 5900619 incorporates advanced engineering principles that enhance its reliability and efficiency. This includes features that promote fuel efficiency, helping users to save on operating costs. By delivering optimal power output while minimizing fuel consumption, this engine part exemplifies the brand's drive towards sustainability and economical operation.

Moreover, the Briggs & Stratton 5900619 is designed for ease of installation. With clear specifications and user-friendly guidelines, it allows both DIY enthusiasts and professionals to replace parts without extensive technical knowledge. This feature is particularly beneficial for those who value efficiency in their maintenance routines.

Another important characteristic of the 5900619 is its performance consistency. Users can expect reliable starts and steady operation, which is critical when tackling large areas of lawn or garden spaces. The engine’s design includes features that help maintain stable power flow, reducing the chances of stalling or unexpected performance issues.

In summary, the Briggs & Stratton 5900619 is a standout choice for anyone looking to enhance their lawn care equipment. With its compatibility across various mower models, durability, advanced technology, ease of installation, and consistent performance, it represents a significant investment in maintaining the health and efficiency of outdoor machinery. This engine part is not just a replacement—it’s a commitment to better gardening outcomes.
Top Page Image Contents