Briggs & Stratton 5900619 manual Pump Drive Belt Removal, Pump Drive Belt Replacement

Page 50

Troubleshooting, Adjustment & Service

Troubleshooting

Pump Drive Belt Removal

1.Park the tractor on a smooth, level surface such as a concrete floor. Disengage the PTO, engage the parking brake, turn off the engine, and remove the ignition key.

2.Remove the PTO drive belt from the clutch (see CLUTCH BELT REMOVAL for instructions).

3.Using a 1/2” breaker bar, place the square end in the square hole located in the middle of the idler arm (A, Figures 50). Carefully rotate the breaker

bar COUNTER-CLOCKWISE, which will relieve the tension on the belts exerted from the idler arm.

WARNING

Use extreme caution when rotating the idler arm with the breaker bar, due to the increased tension in the spring as the idler arm is being rotated. Injury may result if the breaker bar is prematurely released while the spring is under tension.

4.Remove the belts from the right-hand and left- hand pump drive pulley grooves.

5.Carefully release the tension on the breaker bar.

6.Unhook the spring (B) from the anchor bolt on the idler arm.

7.Remove the belts from the crankshaft pulley grooves and pull out from behind the clutch.

Pump Drive Belt Replacement

1.Place the belts under clutch into the crankshaft pulley grooves.

2.Wrap the belts around the top side of the idler arm pulley and install the belts in the right-hand pump pulley grooves.

3.Reinstall the spring onto the anchor bolt on the idler arm.

4.Carefully rotate the idler arm with the breaker bar COUNTER-CLOCKWISE (see Figure 50). While holding the breaker bar firmly, install the belts in the left-hand pump pulley grooves and the two stationary idler pulleys grooves.

5.Carefully release the tension on the breaker bar.

6.Inspect the belt path making sure that all belts are properly seated in the pulley grooves.

7.Reinstall the clutch belts (see CLUTCH BELT REPLACEMENT for instructions).

B

A

Figure 50. Pump Belt Removal & Replacement

A.Pump Drive Idler Arm

B.Spring

48

www.ferrisindustries.com

Page 49 Page 51
Image 50
Page 49 Page 51
Contents
Manual Date Purchased Table of Contents Operating Safety Slope Operation Roll Bar Use Fuel and Maintenance Operation Slope Operation Service and Maintenance Roll BAR Instructions Inspection and Maintenance of the Roll BAR Seat Belt CE Identification TAG Markings North American Models CE Models Export Safety DecalsSafety Decals Safety Icons Operational Safety Checks Safety Interlock SystemSafety Interlock System Ignition Switch Features & ControlsSeat Adjustment Lever Ground Speed LeversHour Meter / Maintenance Reminder PTO Power Take Off SwitchGlow Plug Indicator Oil Pressure IndicatorChecks Before Starting General Operating SafetyOperation On the water separator Priming the Fuel SystemTo prime the fuel system On the engine fuel filterDriving the Tractor Starting the EngineStopping the Tractor & Engine Pushing the Rider by Hand Do not TOW RiderForward Travel Practice Zero Turn Driving PracticeSmooth Travel Reverse Travel PracticeExecuting an End-Of-Row Zero Turn Practice Turning Around a CornerPractice Turning In Place Executing TurnsHeight of Grass MowingMowing Recommendations Tall Grass Requires Incremental CuttingMowing Patterns When and How Often to MowMowing Methods Proper Broadcast MowingAttaching a Trailer Proper MulchingTo raise the roll bar Raise & Lower the Roll BARTo lower the roll bar Keep roll bar in the raised position and use seat beltDiesel Fuel Recommendations StorageStarting After Long Term Storage Temporary Storage 30 Days Or LessCheck Tire Pressures Regular MaintenanceMaintenance Schedule & Procedures Before Every Spring Each 100 250 Fall Use HoursTo add fuel Checking / Adding FuelFuel Filter Hydraulic OIL Filter Change Check / ADD Engine OILCheck / Change AIR Filter Check Hydraulic OIL Level Change Interval Every 500 Hours Filter Part NumberRadiator Pressure Cap Change Engine Coolant Clean RADIATOR, Screen & OIL CoolerCheck Engine Coolant Level Radiator ScreenLubrication Grease OilANTI-SCALP Deck Casters Battery MaintenanceCleaning the Battery and Cables Servicing the Mower Blades Removing the BladeTroubleshooting the Rider Troubleshooting, Adjustments & ServiceTroubleshooting Warning Troubleshooting the Mower Troubleshooting, Adjustment & ServiceRider Troubleshooting Troubleshooting Common Cutting Problems StreakingSpeed Balancing Adjustment Seat AdjustmentGround Speed Lever Adjustment Neutral Position Adjustment Neutral AdjustmentNeutral Position and Return Spring Adjustment Return Spring Adjustment5,4cm Parking Brake Adjustment1/8 To discover how many shims are needed Rear Tire Camber AdjustmentInstalling the camber shims Distance Measured Number of ShimsUse two hands when adjusting the shock Suspension AdjustmentTo adjust the spring pre-load Springs. This will prevent the wrench fromMowing Height Adjustment Outer Rod Deck Lift ROD Timing Adjustment Inner Rod Deck Leveling Adjustment Deck Lift SpringSide Discharge Model Models Rear Discharge Models Belt Removal & ReplacementMower Drive Belt Removal Replacement Clutch Belt Replacement Clutch Belt RemovalPump Drive Belt Replacement Pump Drive Belt RemovalChanging Gearbox Oil Gearbox MaintenanceCheck Gearbox Oil Level FrontBattery Service Checking Battery VoltageTroubleshooting, Adjustment & Service Jump StartingEngine SpecificationsDimensions ChassisFerris Limited Warranty OPERATOR’S Manual
Top Page Image Contents