Briggs & Stratton 5900619 manual Specifications, Engine, Chassis, Transmissions, Dimensions

Page 54

Specifications

NOTE: Specifications are correct at time of printing and are subject to change without notice.

*Actual sustained equipment horsepower will likely be lower due to operating limitations and environmental

factors.

ENGINE:

33 HP* Caterpillar

Make

Caterpillar

Model

3013E

Horsepower

33 @ 3600 rpm

Displacement

91.54 Cu. in (1500 cc)

Electrical System

12 Volt, 16 amp. Alternator, Battery: 500

 

CCA

Oil Capacity

11.5 Pt. (5.4 L) w/ Filter

CHASSIS:

Fuel Tanks

Capacity: 13 Gallons (49.2 L) Total

Rear Wheels

Tire Size: 26 x 12.00 -12

 

Inflation Pressure: 15 psi (1,03 bar)

Front Wheels

Tire Size: 13 x 6.50 - 6

 

Inflation Pressure: 25 psi (1,72 bar)

TRANSMISSIONS:

HydroGear BDP-21 / Parker TF-040

Type

Pump and Wheel Motor

Hydraulic Fluid

Mobil 1™ 15W-50 synthetic oil or

 

Castrol Syntec™ 5W-50 oil

Speeds

Forward: 0-11 MPH (0-17.7 km/h)

@ 3400 rpm

Reverse: 0-5 MPH (0-9.65 km/h)

Continuous Torque

483 ft. lbs. (654 N.m.)

Output

 

Maximum Weight

3000 lbs. (1360 Kg)

on Axle

 

DIMENSIONS:

Overall Length

87” (221 cm)

Overall Width

 

72” Side Discharge

85” (216 cm)

72” Rear Discharge

73” (185 cm)

61” Side Discharge

62” (157 cm)

Height

55” (140 cm)

Weight (apx.)

 

w/ 72” Deck

1908 lbs. (865 kg)

w/ 61” Deck

1887 lbs. (856 kg)

Engine Power Rating Information

The gross power rating labels for individual gas engine models meet or exceed SAE (Society of Automotive Engineers) code J1940 (Small Engine Power & Torque Rating Procedure) and rating performance has been obtained and corrected in accordance with SAE J1995 (Revision 2002-05). Actual gross engine power may be lower and is affected by, but not limited to, ambient operating conditions and engine to engine variability. Given both the wide array of products on which engines are placed, and the variety of environmental issues applicable to operating the equipment, the gas engine will not develop the rated gross power when used in a given piece of power equipment (actual “on-site” or net horsepower). This difference is due to a variety of factors including, but not limited to, accessories (air cleaner, exhaust, charging, cooling, carburetor, fuel pump, etc.), application limitations, ambient operating conditions (temperature, humidity, altitude), and engine to engine variability.

Specifications

52

www.ferrisindustries.com

Page 53 Page 55
Image 54
Page 53 Page 55
Contents Manual Date Purchased Table of Contents Operating Safety Slope Operation Roll Bar Use Fuel and Maintenance Operation Slope Operation Service and Maintenance Roll BAR Instructions Inspection and Maintenance of the Roll BAR Seat Belt CE Identification TAG Markings Safety Decals Safety DecalsNorth American Models CE Models Export Safety Icons Safety Interlock System Safety Interlock SystemOperational Safety Checks Ignition Switch Features & ControlsSeat Adjustment Lever Ground Speed LeversHour Meter / Maintenance Reminder PTO Power Take Off SwitchGlow Plug Indicator Oil Pressure IndicatorGeneral Operating Safety OperationChecks Before Starting On the water separator Priming the Fuel SystemTo prime the fuel system On the engine fuel filterStarting the Engine Stopping the Tractor & EngineDriving the Tractor Pushing the Rider by Hand Do not TOW RiderForward Travel Practice Zero Turn Driving PracticeSmooth Travel Reverse Travel PracticeExecuting an End-Of-Row Zero Turn Practice Turning Around a CornerPractice Turning In Place Executing TurnsHeight of Grass MowingMowing Recommendations Tall Grass Requires Incremental CuttingMowing Patterns When and How Often to MowMowing Methods Proper Broadcast MowingAttaching a Trailer Proper MulchingTo raise the roll bar Raise & Lower the Roll BARTo lower the roll bar Keep roll bar in the raised position and use seat beltDiesel Fuel Recommendations StorageStarting After Long Term Storage Temporary Storage 30 Days Or LessCheck Tire Pressures Regular MaintenanceMaintenance Schedule & Procedures Before Every Spring Each 100 250 Fall Use HoursChecking / Adding Fuel Fuel FilterTo add fuel Hydraulic OIL Filter Change Check / ADD Engine OILCheck / Change AIR Filter Check Hydraulic OIL Level Change Interval Every 500 Hours Filter Part NumberRadiator Pressure Cap Change Engine Coolant Clean RADIATOR, Screen & OIL CoolerCheck Engine Coolant Level Radiator ScreenLubrication Grease OilBattery Maintenance Cleaning the Battery and CablesANTI-SCALP Deck Casters Servicing the Mower Blades Removing the BladeTroubleshooting, Adjustments & Service Troubleshooting WarningTroubleshooting the Rider Troubleshooting, Adjustment & Service Rider TroubleshootingTroubleshooting the Mower Troubleshooting Common Cutting Problems StreakingSeat Adjustment Ground Speed Lever AdjustmentSpeed Balancing Adjustment Neutral Position Adjustment Neutral AdjustmentNeutral Position and Return Spring Adjustment Return Spring AdjustmentParking Brake Adjustment 1/85,4cm To discover how many shims are needed Rear Tire Camber AdjustmentInstalling the camber shims Distance Measured Number of ShimsUse two hands when adjusting the shock Suspension AdjustmentTo adjust the spring pre-load Springs. This will prevent the wrench fromMowing Height Adjustment Deck Lift ROD Timing Adjustment Inner RodOuter Rod Deck Leveling Adjustment Deck Lift SpringBelt Removal & Replacement Mower Drive Belt Removal ReplacementSide Discharge Model Models Rear Discharge Models Clutch Belt Replacement Clutch Belt RemovalPump Drive Belt Replacement Pump Drive Belt RemovalChanging Gearbox Oil Gearbox MaintenanceCheck Gearbox Oil Level FrontBattery Service Checking Battery VoltageTroubleshooting, Adjustment & Service Jump StartingEngine SpecificationsDimensions ChassisFerris Limited Warranty OPERATOR’S Manual

5900619 specifications

The Briggs & Stratton 5900619 is a highly regarded replacement engine part designed specifically for a range of lawn and garden equipment, ensuring optimal performance and reliability. Known for its durability and innovation, this part caters to those who require dependable machinery for their outdoor tasks.

One of the key features of the Briggs & Stratton 5900619 is its compatibility with a variety of mower models, making it a versatile choice for both amateur and professional landscapers. This adaptability not only streamlines the maintenance process but also reduces downtime, allowing users to focus on their landscaping tasks rather than equipment issues.

The construction of the Briggs & Stratton 5900619 highlights the brand's commitment to quality. Made from robust materials, this replacement part is designed to withstand harsh outdoor conditions. This ruggedness ensures that it can handle the wear and tear often associated with regular use in challenging environments, contributing to a longer lifespan for both the engine and the machinery it services.

In terms of technology, the Briggs & Stratton 5900619 incorporates advanced engineering principles that enhance its reliability and efficiency. This includes features that promote fuel efficiency, helping users to save on operating costs. By delivering optimal power output while minimizing fuel consumption, this engine part exemplifies the brand's drive towards sustainability and economical operation.

Moreover, the Briggs & Stratton 5900619 is designed for ease of installation. With clear specifications and user-friendly guidelines, it allows both DIY enthusiasts and professionals to replace parts without extensive technical knowledge. This feature is particularly beneficial for those who value efficiency in their maintenance routines.

Another important characteristic of the 5900619 is its performance consistency. Users can expect reliable starts and steady operation, which is critical when tackling large areas of lawn or garden spaces. The engine’s design includes features that help maintain stable power flow, reducing the chances of stalling or unexpected performance issues.

In summary, the Briggs & Stratton 5900619 is a standout choice for anyone looking to enhance their lawn care equipment. With its compatibility across various mower models, durability, advanced technology, ease of installation, and consistent performance, it represents a significant investment in maintaining the health and efficiency of outdoor machinery. This engine part is not just a replacement—it’s a commitment to better gardening outcomes.
Top Page Image Contents