Briggs & Stratton 150Z Series manual Service & Adjustments, Ground Speed Control Lever Adjustment

Page 27

SERVICE & ADJUSTMENTS

GROUND SPEED CONTROL LEVER ADJUSTMENT

The control levers have three adjustments:

To Adjust Control Lever Height: Pull the levers in across the operator’s lap to their DRIVE positions. Loosen the mount bolts (D, Figure 32) and raise or lower the levers to the desired position. Tighten the mounting bolts.(D).

To Adjust Control Lever End Gap: The control lever end gap (C, Figure 33) should be adjusted so that the levers do not contact each other when placed in DRIVE positions. Loosen the jam nut (A, Figure 32) and adjust the length of the carriage bolt (B) so that the levers do not contact each other. Repeat on the opposite side. Tighten the jam nut (A) to lock the carriage bolt in position.

To Adjust Operator Clearance: The space between the operator and the control levers can be increase by removing the lower mounting bolt (D, Figure 32), pivoting the lever forward, and reinstalling the capscrew through the control lever and forward slot (C). Repeat with the other ground speed lever.

C

A

D

B

E

Figure 32. Control Lever Adjustment

A.Jam Nut

B.Carriage Bolt

C.Forward Slot

D.Mount Bolts

E.Knob

SPEED BALANCING ADJUSTMENT

If the rider veers to the right or left when the ground speed control levers are in the maximum forward position, the top speed of the right lever can be balanced by turning the adjustment knob (E, Figure 32). Loosen the jam nut and turn the knob COUNTERCLOCKWISE

to increase speed or CLOCKWISE to decrease speed. Tighten the jam nut when complete.

C

CUTTING HEIGHT ADJUSTMENT

To increase the mower cutting height (raise the mower deck), press the top of the mower cutting height switch (A, Figure 33) To decrease mower cutting height (lower the mower deck), press the bottom of the switch. Mower cutting height range is 3-3/4” to 1-1/2”. The cutting height gauge indicates the position of the mower deck.. The cutting height gauge (B) is located on the front of the rider, just behind the driver’s left leg.

PTO CLUTCH ADJUSTMENT

See CHECK / ADJUST PTO CLUTCH in the Maintenance Section.

 

A

 

 

HCutting

 

 

eight

 

B

3

 

 

4

HighCut

 

 

 

2

 

 

1

 

 

Low Cut

Figure 33. Cutting Height Adjustment

A.Cutting Height Adjustment Switch

B.Cutting Height Gauge

C.Control Lever End Gap

25

Page 26 Page 28
Image 27
Page 26 Page 28
Contents 20HP Zero-Turn Riders OPERATOR’S ManualPage Table of Contents General Operation Safety RulesIgnition System Only Ride UP and Down Hill Not Across Hill Degrees MAX Safe Handling of Gasoline Service & Maintenance2690716 Safety & Operation DecalsMfg. No ID Tag Identification NumbersEngine Speed Control OperationControl Functions Ground Speed Levers Parking BrakeGeneral Operating Safety Fuel Recommendations Checks Before StartingMowing Emergency StoppingStopping the Rider & Engine Starting the EngineReverse Travel Practice Driving PracticeSmooth Travel Forward Travel PracticeExecuting an End-Of-Row Zero Turn Practice Turning Around a CornerPractice Turning In Place Executing TurnsMower Deck Removal Installation Installing the Mower DeckRemoving the Mower Deck 20HP Briggs & Stratton MaintenanceMaintenance Schedule Rider MAINTENANCE, All ModelsCheck Tire Pressure Accessing the Engine CompartmentClean Debris from Rider Engine Compartment Clean Debris from Engine Cooling Areas and AIR FilterLubrication GreaseOil Blade Removal Clean Deck Check / Replace Mower BladesClean the Battery and Cables Check Rider Safety SystemOperational Safety Checks Adjust PTO Clutch Window Adjustment Nut Feeler Gauge Check / Adjust PTO ClutchCheck Engine OIL Level Change Engine OILChange Engine OIL & Filter Air Filter Removal & Installation Service AIR Filter PRE-CLEANERPre-Cleaner Service Air Filter Service Pre-CleanerReplace Spark Plug Cutting Height Adjustment Service & AdjustmentsGround Speed Control Lever Adjustment Speed Balancing Adjustment62cm Brake AdjustmentBattery Charging Engine AdjustmentsSide to Side Leveling Mower Deck Leveling AdjustmentsMower Belt Replacement Mower Drive Belt ReplacementFront To Back Leveling After Storage StorageStorage Before StorageTroubleshooting the Rider TroubleshootingTroubleshooting the Mower Chassis SpecificationsService Items Engine TransmissionPage HOW High to MOW the Grass HOW and When toWATER, Fertilize AerateProper Mowing Speed When and HOW Often to MOW
Top Page Image Contents