Bolens 13B-325-401 Servicing Your Rider Mower, Fuse Replacement, Belt Replacement, Deck Belt

Page 16

SECTION 7: SERVICING YOUR RIDER MOWER

Fuse Replacement

The fuse is located next to the spark plug under the rear frame. Fuses seldom fail without a reason. If the fuse blows, the source problem must be corrected or the new fuse will blow again.

•Check for loose connections in the fuse holder and replace holder if necessary. A dead short may be in the cranking or charging circuit where insulation may have rubbed through and exposed bare wire.

•Replace the wire or repair with electrician’s tape if the wire strands have not been damaged. Also look for a wire pinched between body panels, burned by the exhaust pipe or muffler, or rubbed against a moving part.

•Stop the rider mower and engage the parking brake. Remove ignition key.

•Pivot the hood assembly up. Disconnect the spark plug wire and ground it.

•Pull the fuse out of the lead wire.

•Replace with new automotive fuse.

Imaginary

BeltLine

Keeper

Deck Belt

Cover

Hex

Nut

Lock

Washer

Self-Tapping

Screw

Deck

Pulley

Belt Keeper “A”

Hex

Nut

Idler

Pulley

Make sure to reconnect the spark plug wire before pivoting the hood assembly back.

Belt Replacement

There are two drive belts and one deck belt in your rider mower; follow the description below to identify the belts.

1.The lower drive belt goes from the variable speed pulley to the transmission pulley.

2.The upper drive belt goes from the variable speed pulley to the upper sheave of engine pulley.

3.The deck belt goes from the deck pulley to the lower sheave in engine pulley.

•Periodically check to see if these belts are too loose or damaged through wear and tear. If so, replace with new belt.

Deck Belt

•Engage the parking brake and turn the ignition off. Pivot the hood assembly up and remove the grass catcher. Remove the spark plug wire.

•Put the deck at the lowest cutting height by adjusting the cutting height adjustment lever to the lowest position.

•Using a 1/2” socket wrench, remove two self- tapping screws, lock washer and hex nut that hold the deck belt cover to the deck. See Figure 16 . For this, you will have to work from the top left side of the mower. Remove the belt cover.

•Using a 9/16” wrench, loosen the hex nut on the idler pulley. See Figure 16.

Figure 16

•Remove belt from around deck pulley, idler pulley, and the engine pulley.

•Place the new belt around the deck pulley and the engine pulley making sure that the belt is routed inside the belt keepers. There are two belt keepers under the grass catcher, one on the idler and the other under the deck belt cover. See Figure 16.

•Reinstall deck belt cover and secure with two self- tapping screws, lock washer and hex nut.

NOTE: Belt keeper “A” must be mounted on the outside of the belt.

•Make sure to align the belt keeper in line with the frame. See Figure 16.

NOTE: An imaginary line between the belt keeper and idler pulley should be parallel to frame. See Figure 16.

•Replace the grass catcher and pivot the hood assembly back.

Lower Variable Speed Belt

•Remove the rear deck belt guard following first five steps for deck belt removal. Remove belt from the engine pulley.

•Push the spring loaded idler, located on the left side of the transmission, to the right. Remove belt from around the idler and then the transmission pulley. See Figure 17 .

16

Page 15 Page 17
Image 16
Page 15 Page 17
Contents Operator’s Manual Table of Contents General Operation Important Safe Operation PracticesSlope Operation Do Not ServiceChildren Tires and other harmful waste Slope Guage Attaching Battery Cables Unpacking & Assembling Your Rider MowerLoose Parts Attaching Side-Discharge ChuteAttaching Bumper If equipped Attaching Mulch PlugAttaching Hitch Plate If equipped Know Your Rider Mower Safety Interlock Using Shift LeverGrass Fill Level Indicator Stopping MowerOperating Your Rider Mower Using The Mower Go Pedal Brake PedalCutting Height Adjusting the Deck Test 1 Checking Rear Deck Height AdjustmentSeat Position Blade Brake/PTOAdjusting Rear Deck Height Test 2 Checking Front to Rear LevellingTest 3 Checking Side to Side Levelling Front to Rear LevellingFuse Replacement Belt ReplacementServicing Your Rider Mower Deck BeltGeneral Recommendations Maintaining Your Rider MowerCutting Blade Engine Oil Drain SleeveLubrication Cleaning Engine Fuel FilterTROUBLE-SHOOTING Trouble Possible Cause Remedial ActionCharge with 6 Amp. charger until fully Parts List for Series Model 320 Series Model 320 Series 4323 735-0261 2216 712-3010 Hex Nut 5/16-18 714-0115 Description 683-0147 2718 33 4 712-0267 List of color codes below. Please add Model 320 Series Spindle Assembly 683-0150C 11 26 Description Safety & Decorative Labels Your Notes MANUFACTURER’S Limited Warranty for

13B-325-401 specifications

The Bolens 13B-325-401 is a versatile riding lawnmower designed for homeowners who require reliable performance and ease of use in their lawn maintenance. This model, known for its powerful engine and user-friendly features, is tailored to handle a variety of landscaping tasks with precision.

At the heart of the Bolens 13B-325-401 is a robust 13.5 horsepower Briggs & Stratton engine. This engine provides ample power to tackle tough grass and uneven terrain, making it suitable for larger residential lawns. The engine is designed for easy starting, featuring a recoil system that ensures quick operation, reducing downtime and making yard work more efficient.

One of the standout features of the 13B-325-401 is its 42-inch cutting deck. This wide cutting area allows users to cover more ground in less time, and the precise design promotes an even cut across different grass types. The deck is equipped with adjustable cutting heights, allowing operators to customize the lawn cut to their desired level. With six different cutting positions, users can transition from a manicured look to a more natural finish depending on their landscaping needs.

The mower also includes a responsive hydrostatic transmission, which provides seamless speed control without the complications of manual shifting. This feature allows for effortless transitioning between forward and reverse, making maneuvering around obstacles like flower beds or trees much easier. The intuitive controls are strategically placed, ensuring that operators can adjust their speed and direction smoothly while maintaining a comfortable grip.

Durability is a key characteristic of the Bolens 13B-325-401. The heavy-duty steel frame is designed to withstand the rigors of regular use, ensuring longevity. Additionally, the mower’s compact design allows for easy storage, even in tight spaces.

User comfort has not been overlooked. The mower offers a plush seat that is adjustable, providing support during longer mowing sessions. The ergonomic steering wheel and dashboard layout improve the overall user experience, allowing for easy access to essential controls such as the ignition and throttle.

In summary, the Bolens 13B-325-401 combines power, efficiency, and comfort, making it an excellent choice for homeowners looking to simplify lawn care. Its advanced features, including a reliable engine, adjustable cutting deck, and user-friendly design, create a machine capable of maintaining beautiful lawns with confidence and ease.
Top Page Image Contents