Bolens 13B-325-401 Unpacking & Assembling Your Rider Mower, Loose Parts, Attaching Battery Cables

Page 7

SECTION 3: UNPACKING & ASSEMBLING YOUR RIDER MOWER

•Remove all screws and staples from crate.

•Holding the sides of the crate firmly, lift the top of the crate up and keep it aside. Avoid tire punctures.

•Remove and discard plastic bag covering the unit.

•Lift the rear of the mower and clear the bottom of the crate. Repeat for the front.

•Be sure parking brake is disengaged. See Figure 8 for location of parking brake. Roll unit out of the crate’s way.

Loose Parts

•Remove loose parts from the grass catcher and/or the crate very carefully. Compare with list and illustration (Figure 1) below.

1.Mulching plug & side-discharge chute

2.Oil drain sleeve

3.Bumper (optional)

4.Ignition keys (not shown)

5.Operator’s manual (not shown)

Side-Discharge

Chute

Oil Drain

Sleeve

Mulching

Bumper

Plug

 

Figure 1

Attaching Battery Cables

The battery is located under the hood assembly above the left rear wheel. Refer to Figure 3 .

•To access the battery, lift the hood assembly from the left side of the hood only. Stand on the right side of the unit and pivot the hood assembly towards you until fully opened. See Figure 2 .

CAUTION: Do not lift the hood assembly by the two vent openings located behind the seat.

Vent

Opening

Hood Assembly

Figure 2

•Remove both wing nuts securing the battery and cover to the battery hold-down rods. See Figure 3 .

•Remove red and black insulation caps from battery terminals. See Figure 3

•Remove battery terminal screws with a Phillips screw driver or a 10 mm. socket wrench.

•Attach the red battery cable to the positive terminal (marked +), and the black battery cable to the negative terminal (marked -) on the battery. See Figure 3 .

•Align the cables with the slots in the battery cover and tighten the screws on the battery terminals.

WARNING: Press the battery cables against side of battery so that these do not make contact with flange of rider frame when it is opened or closed.

•Reassemble the battery cover to the hold-down rods on two ends with the two wing nuts removed earlier. Check to ensure that the cables pass easily through slots in cover.

•Place right hand on the left side of the seat and slowly lower the hood assembly untill fully closed.

CAUTION: Do not place your hand around the bottom edge of the hood assembly; it may get pinched between the hood assembly and grass catcher or the frame rail.

 

 

 

Wing

 

 

 

Wing

 

 

 

 

 

 

Nut

 

 

 

 

Nut

Negative

 

 

Positive

Battery

Terminal

 

 

 

 

Terminal

Cover

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Battery

Cable

Rider

Frame

Figure 3

WARNING: Battery posts, terminals and related accessories contain lead and lead compounds. Wash hands after handling.

Attaching Side-Discharge Chute

Your riding mower is shipped to you with the grass catcher fully assembled on the unit. A side-discharge chute and a mulching plug are included as loose parts. Follow the instructions below to attach the side- discharge chute.

7

Page 6 Page 8
Image 7
Page 6 Page 8
Contents Operator’s Manual Table of Contents General Operation Important Safe Operation PracticesSlope Operation Do Not ServiceChildren Tires and other harmful waste Slope Guage Attaching Side-Discharge Chute Attaching Battery CablesUnpacking & Assembling Your Rider Mower Loose PartsAttaching Bumper If equipped Attaching Mulch PlugAttaching Hitch Plate If equipped Know Your Rider Mower Stopping Mower Safety InterlockUsing Shift Lever Grass Fill Level IndicatorOperating Your Rider Mower Using The Mower Go Pedal Brake PedalCutting Height Blade Brake/PTO Adjusting the DeckTest 1 Checking Rear Deck Height Adjustment Seat PositionFront to Rear Levelling Adjusting Rear Deck HeightTest 2 Checking Front to Rear Levelling Test 3 Checking Side to Side LevellingDeck Belt Fuse ReplacementBelt Replacement Servicing Your Rider MowerGeneral Recommendations Maintaining Your Rider MowerCutting Blade Engine Oil Drain SleeveLubrication Fuel Filter Cleaning EngineTrouble Possible Cause Remedial Action TROUBLE-SHOOTINGCharge with 6 Amp. charger until fully Parts List for Series Model 320 Series Model 320 Series 4323 735-0261 2216 712-3010 Hex Nut 5/16-18 714-0115 Description 683-0147 2718 33 4 712-0267 List of color codes below. Please add Model 320 Series Spindle Assembly 683-0150C 11 26 Description Safety & Decorative Labels Your Notes MANUFACTURER’S Limited Warranty for

13B-325-401 specifications

The Bolens 13B-325-401 is a versatile riding lawnmower designed for homeowners who require reliable performance and ease of use in their lawn maintenance. This model, known for its powerful engine and user-friendly features, is tailored to handle a variety of landscaping tasks with precision.

At the heart of the Bolens 13B-325-401 is a robust 13.5 horsepower Briggs & Stratton engine. This engine provides ample power to tackle tough grass and uneven terrain, making it suitable for larger residential lawns. The engine is designed for easy starting, featuring a recoil system that ensures quick operation, reducing downtime and making yard work more efficient.

One of the standout features of the 13B-325-401 is its 42-inch cutting deck. This wide cutting area allows users to cover more ground in less time, and the precise design promotes an even cut across different grass types. The deck is equipped with adjustable cutting heights, allowing operators to customize the lawn cut to their desired level. With six different cutting positions, users can transition from a manicured look to a more natural finish depending on their landscaping needs.

The mower also includes a responsive hydrostatic transmission, which provides seamless speed control without the complications of manual shifting. This feature allows for effortless transitioning between forward and reverse, making maneuvering around obstacles like flower beds or trees much easier. The intuitive controls are strategically placed, ensuring that operators can adjust their speed and direction smoothly while maintaining a comfortable grip.

Durability is a key characteristic of the Bolens 13B-325-401. The heavy-duty steel frame is designed to withstand the rigors of regular use, ensuring longevity. Additionally, the mower’s compact design allows for easy storage, even in tight spaces.

User comfort has not been overlooked. The mower offers a plush seat that is adjustable, providing support during longer mowing sessions. The ergonomic steering wheel and dashboard layout improve the overall user experience, allowing for easy access to essential controls such as the ignition and throttle.

In summary, the Bolens 13B-325-401 combines power, efficiency, and comfort, making it an excellent choice for homeowners looking to simplify lawn care. Its advanced features, including a reliable engine, adjustable cutting deck, and user-friendly design, create a machine capable of maintaining beautiful lawns with confidence and ease.
Top Page Image Contents