Bolens 13B-325-401 manual Seat Position, Blade Brake/PTO, Wheel Alignment, Adjusting the Deck

Page 14

Seat Position

The seat position on the rider mower can be adjusted to maximize the operator’s convenience.

•Stop the mower completely and engage the parking brake. Turn ignition off.

•Pivot the hood assembly up.

•Loosen the four self-tapping screws on the bottom of the seat.

•Slide the seat forward or backward in the slot, and position it as desired. Retighten the four screws.

Blade Brake/PTO

The blade engagement pedal should be adjusted so that if you depress it about 3/4” from the front of the slot, it should start engaging the deck belt. The PTO (power take off) switch is located in the blade brake slot on the left side of the upper frame. See Figure 13 . The brake engagement pedal needs to make contact with the PTO switch for the engine to start.

Under normal operation, the blade engagement pedal should not require frequent adjustment. However, perform the following test periodically and make sure that it is in fine working condition.

•

Pivot the hood assembly up and check if there is

 

enough slack on the deck engagement cable.

•

Depress the blade engagement pedal (about 3/4

 

inch) and check if the belt is engaging.

•If the belt is slipping when you depress the blade engagement pedal about 3/4”, loosen the two hex nuts on the cable. See Figure 13.

•If the belt is engaging sooner than when the blade engagement pedal is 3/4” from the PTO switch, tighten both hex nuts on the cable. See Figure 13.

•Repeat the blade engagement test and readjust if necessary.

•Pivot the hood assembly back.

Wheel Alignment

The front wheels should toe-in 1/16-5/16 inch. To adjust toe-in, follow these steps:

•Remove the 3/8’’ hex nut which holds the ball joint to the steering segment. See Figure 14.

•Adjust the ball joint in or out until the wheels toe-in approximately 1/16-5/16" (Dimension ‘‘B’’ should be approximately 1/16-5/16" less than dimension ‘‘A’’). See Figure 14.

•Replace the ball joint into the steering segment, and replace the 3/8’’ hex nut.

Hex Nut

Lock

•

If the cable is tight or too loose or the belt is not

Steering

Washer

engaging, adjust the deck engagement cable.

NOTE: The deck engagement cable will be correctly adjusted when the cable moves approximately 1/2” off center line in both directions.

Adjustment to the blade brake will have to be made at the cable end. See Figure 13.

Deck

Hex

Engagement

Nut

Cable

 

Blade Engagement

Pedal

PTO

Switch

Figure 13

Segment

Tie

Rod

Ball

Joint

A

front

B

1/16-5/16’’ less than A

Figure 14

Adjusting the Deck

There are three tests for checking deck levelling on the rider mower. The results of each test will determine what kind of levelling, if at all, the equipment needs.

IMPORTANT: Perform adjustments to the deck on a flat, level surface. Before continuing with deck adjustment, check air pressure in all four tires. Recommended air pressure is 12 psi. Please note that the valve stems on this rider mower are on the inside of the front wheels and on the outer side of the rear wheels.

Test 1: Checking Rear Deck Height Adjustment

•Lift the hood assembly and remove grass catcher from the rider mower. Place the deck in the highest position.

•Inspect rear of deck. If the deck is contacting the cable bracket on the front of the transmission, you will have to adjust the rear deck height.

14

Page 13 Page 15
Image 14
Page 13 Page 15
Contents Operator’s Manual Table of Contents Slope Operation Important Safe Operation PracticesGeneral Operation Children ServiceDo Not Tires and other harmful waste Slope Guage Loose Parts Attaching Battery CablesUnpacking & Assembling Your Rider Mower Attaching Side-Discharge ChuteAttaching Hitch Plate If equipped Attaching Mulch PlugAttaching Bumper If equipped Know Your Rider Mower Grass Fill Level Indicator Safety InterlockUsing Shift Lever Stopping MowerOperating Your Rider Mower Using The Mower Cutting Height Brake PedalGo Pedal Seat Position Adjusting the DeckTest 1 Checking Rear Deck Height Adjustment Blade Brake/PTOTest 3 Checking Side to Side Levelling Adjusting Rear Deck HeightTest 2 Checking Front to Rear Levelling Front to Rear LevellingServicing Your Rider Mower Fuse ReplacementBelt Replacement Deck BeltCutting Blade Maintaining Your Rider MowerGeneral Recommendations Lubrication Oil Drain SleeveEngine Cleaning Engine Fuel FilterTROUBLE-SHOOTING Trouble Possible Cause Remedial ActionCharge with 6 Amp. charger until fully Parts List for Series Model 320 Series Model 320 Series 4323 735-0261 2216 712-3010 Hex Nut 5/16-18 714-0115 Description 683-0147 2718 33 4 712-0267 List of color codes below. Please add Model 320 Series Spindle Assembly 683-0150C 11 26 Description Safety & Decorative Labels Your Notes MANUFACTURER’S Limited Warranty for

13B-325-401 specifications

The Bolens 13B-325-401 is a versatile riding lawnmower designed for homeowners who require reliable performance and ease of use in their lawn maintenance. This model, known for its powerful engine and user-friendly features, is tailored to handle a variety of landscaping tasks with precision.

At the heart of the Bolens 13B-325-401 is a robust 13.5 horsepower Briggs & Stratton engine. This engine provides ample power to tackle tough grass and uneven terrain, making it suitable for larger residential lawns. The engine is designed for easy starting, featuring a recoil system that ensures quick operation, reducing downtime and making yard work more efficient.

One of the standout features of the 13B-325-401 is its 42-inch cutting deck. This wide cutting area allows users to cover more ground in less time, and the precise design promotes an even cut across different grass types. The deck is equipped with adjustable cutting heights, allowing operators to customize the lawn cut to their desired level. With six different cutting positions, users can transition from a manicured look to a more natural finish depending on their landscaping needs.

The mower also includes a responsive hydrostatic transmission, which provides seamless speed control without the complications of manual shifting. This feature allows for effortless transitioning between forward and reverse, making maneuvering around obstacles like flower beds or trees much easier. The intuitive controls are strategically placed, ensuring that operators can adjust their speed and direction smoothly while maintaining a comfortable grip.

Durability is a key characteristic of the Bolens 13B-325-401. The heavy-duty steel frame is designed to withstand the rigors of regular use, ensuring longevity. Additionally, the mower’s compact design allows for easy storage, even in tight spaces.

User comfort has not been overlooked. The mower offers a plush seat that is adjustable, providing support during longer mowing sessions. The ergonomic steering wheel and dashboard layout improve the overall user experience, allowing for easy access to essential controls such as the ignition and throttle.

In summary, the Bolens 13B-325-401 combines power, efficiency, and comfort, making it an excellent choice for homeowners looking to simplify lawn care. Its advanced features, including a reliable engine, adjustable cutting deck, and user-friendly design, create a machine capable of maintaining beautiful lawns with confidence and ease.
Top Page Image Contents