Blue Rhino 153300 owner manual Assemble Emitter Top, Attach Engine to Post

Page 9

Contact 1-800-762-1142 for assistance.

Do not return to place of purchase.

Step 5 – Assemble Emitter Top

•Slip (1) Small Bolt through hole in Emitter Top from inside.

•Slip (1) Lockwasher over bolt and thread (1) Large nut all the way down and tighten.

•Repeat for other two holes.

Step 6 – Assemble Emitter

•Curl Emitter Screen into a circle. Overlap ends and line up holes. Secure together using (2) Small screws and (2) small nuts.

• Line up holes in bottom of Emitter Screen with holes in Engine.

• Attach Emitter Screen to Engine with (4) Small Screws.

• Line up holes in top of Emitter Screen with holes in Emitter Top.

• Attach Emitter Screen to Emitter Top with (4) Small Screws.

Step 7 – Attach Engine to Post

• Remove and Save Control Knob.

• Remove and save (3) screws from sides and bottom of Engine Access Panel.

•Open Engine Access Panel.

•Disconnect wire from Igniter by gently pulling wire.

•Remove and save Engine Access Panel.

• Align threaded holes in Post with holes in bottom of Engine.

• Insert (4) Medium Screws loosely. They will be fully tightened at the end of the next step.

Note: Do not replace Engine Access Panel until Step 13.

Owner’s manual and assembly instructions: model 153300 outdoor patio heater

3/28/03

8

Image 9

Contents Manual del Usuario For Outdoor Use Only outside any enclosure 28/03 Safety First 20 lb. LP Cylinder For Your Safety Picture Qty General Components & Features Additional RequirementsAttach Legs to Base Attach Cap Assembly to Legs/Insert Gas Line Attach Cylinder Shroud to LegsAssemble Cup, Plate & Ring to Cap Assemble Emitter Top Assemble EmitterAttach Engine to Post Connect Gas Line to Engine Connect Engine/Post Assembly to CapAttach Dome to Emitter Secure Gas LineConnect Gas Line to Cylinder Check Gas Line / Cylinder valve for leaks Check for LeaksReplace Engine Access Panel Install Cylinder Access PanelBefore Turning Gas Supply on OperationBefore Lighting LightingWhen heater is on Re-lightingShut Down After Operation Before OperatingIf the problem is This condition exists Then do this Maintenance Service During periods of extended inactivity or when transportingBetween uses Warranty Period Certifications Safety FeaturesRating Heat RangeAdvertencia Índice Pour Votre Sécurité ¡La Seguridad, lo PrimeroBouteille de gaz de 9 kg Ferretería ComponentesComponentes Generales y Características Requisitos AdicionalesPaso 1 Acoplar las patas a la base Paso 3 Montar la copa, la placa y el anillo en la cubierta Paso 2 Acoplar la protección de la bombona a las patasPaso 5 Montar la cubierta del emisor Paso 6 Montar el emisorPaso 7 Acoplar el motor al poste Paso 9 Conectar la línea de gas al motor Paso 8 Conectar el conjunto motor/poste a la cubiertaPaso 10 Acoplar la cúpula al emisor Paso 11 Asegurar la línea de gasPaso 12 Conectar la línea de gas a la bombona Compruebe si hay fugas en la línea de gas/bombona Paso 13 Comprobar si hay fugasPaso 15 Volver a colocar el panel de acceso al motor Paso 14 Montar el panel de acceso a la bombonaOperación Antes de activar la alimentación de gas onAntes del encendido Cuando el calentador está encendido on ReencendidoApagado Tras su funcionamiento Antes de la puesta en marchaAcumulación de carbonilla Mantenimiento AdvertenciaServicio Entre uso y usoDurante períodos largos de inactividad o para su transporte Período de Garantía Consumo CertificacionesAlcance calorífico CombustibleNASDAQ-RINO