Demco AC20037 manual Assembly Instructions

Page 21

Assembly Instructions

Preparation: Remove any loader brackets from the tractor. The tractors duals must be set to 120wheel spacing.

1.Remove every other lug bolt on the tractor’s dual, and replace them with the special spacer Stud Bolts included with the SideQuest hardware as shown in VIEW A. (Note: Only when replacing stud bolts on a JD 7000 Series Tractor, the existing washers MUST be used). After all of the removed lug bolts are replaced, remove the rest of the tractor’s lug bolts and replace them with the SideQuest stud bolts. Torque the SideQuest stud bolts to tractor manufacturer’s specifications.

2.Bolt the Hub Spacer to the SideQuest stud bolts as shown in VIEW B. Use ten 7/8-UNF x 2hex head bolts and ten 7/8lockwashers. Then bolt the Hub/Spindle Assembly to the Hub Spacer. Use eight 5/ 8-UNF x 2hex head bolts and lockwashers to bolt the Hub/Spindle Assembly to the Hub Spacer. Torque all bolts to the specifications found earlier in the manual.

3.Mount the Left and Right Base Plates to the tractor’s frame. All Base Plates will mount between the tractors cab and front wheels to existing holes in the tractors frame. All tractors’ mounting brackets can be viewed on pages 14-16.

4.Mount the Tank Holder with Tank, and Tank Hold Downs. Before mounting, decide which height setting is desirable. There are two height settings. Slide the Tank holder over the spindle as shown in VIEW C. Make sure the arrow on the end of the spindle is always pointing up as shown. Use the bottom hole for a higher height setting, and use the top hole for a lower height setting. Slide the tank holder in until there is a spacing of approximately 2between the tire and the Tank Holder. Use four 1/2-UNC x 1 1/4set screws to hold the spindle in place. Turn the set screws into the threaded inserts on the outside of the tube the spindle has been placed in.

5.Next bolt the Mounting Extension Arm to the Tank Holder. Use four 1/ 2-UNC x 1 3/4hex head bolts, four 1/2lockwashers, and four 1/2hex nuts.

6.Repeat same instructions for the opposite side.

NOTE:

View A, B, & C use parts list on next page.

13

VIEW A

4

24

22

1

17

19

VIEW B

1

23

23

VIEW C

Page 21

Image 21
Contents Patent No ,286,870 General Information Table of ContentsWarranty Registration Postage Page Lighting and Marking Equipment Safety GuidelinesSafety Sign Locations Tire Safety Safety Sign CareHow to install safety signs RememberDuring Operation Following Operation Highway and Transport Operations Performing Maintenance Lb-ft N.m Bolt Torque for Standard boltsBolt Torque for Metric bolts ClassHead Mounting Brackets Mounting Brackets7600-7800 & 7610-7810 Series 7720, 7820, & 7920 SeriesSeries OVER-HEAD Mounting BracketsJohn Deere 30’S IVT OVER-HEAD Mounting Brackets Series IVTMX Magnum Parts Breakdown TG Series NEW Holland OVER-HEAD Mounting Brackets Ford Genesis & Buhler OVER-HEAD MountingTG Series New Holland John Deere 8000 Track Mounting Brackets and Skid Installation John Deere 8000 TrackJohn Deere 9000 Track Mounting Brackets and Skid Description NO. no CAT MT765 Challenger Mounting Brackets and SkidAssembly Instructions Hub Breakdown Sidequest Parts BreakdownSidequest Plumbing Breakdown Gallon Sidequest Parts BreakdownRefer to p.22 for replacement part numbers Gallon Sidequest Center Exit 35631 Parts Breakdown Gallon Sidequest Center Exit Parts Breakdown Optional Sidequest Jackstands Breakdown Step Parts Breakdown Optional Sidequest Light KIT Parts Breakdown Parts ListPage Sprayer Checklist Dethmers MFG. Company