Exmark VH15KA362, VH15KA483 manual

Page 35

FIGURE 13

After adjusting the left hydro control linkage, move the speed control lever to the mid-speed position and then back to the neutral position. Recheck the left drive wheel rotation to see if further adjustment is necessary - be sure the speed control lever is in the neutral position.

If inconsistent neutral occurs, check to be sure both springs are properly tightened on the speed control lever under the console - especially the rear pivot spring.

Repeat above adjustments if necessary.

3.Place the speed control lever in neutral. Adjust the right side linkage by turning the quick track knob counter-clockwise until the tire begins to rotate forward. Begin to retighten the knob clockwise about 1/4 turn at a time, stopping to move the speed control forward and back to neutral. Recheck the drive wheel rotation to see if further adjustment is necessary.

4.The spring that keeps tension on the knob should normally not need adjustment. However, if adjustment is needed, adjust to where length of spring is about 1” (2.5 cm) between the washers. Adjust spring length by turning nut at front of spring.

d)Drive Lever Linkage Adjustment

1.With rear of machine still on jack stands and engine running at full throttle, disengage the park brake and move the speed control lever to the midway position. Move the respective drive lever upward until it reaches the neutral position and engage neutral lock latches. See Figure 14. If the tire rotates in either direction, the length of the drive lever link will need to be adjusted.

2.Adjust the linkage length by loosening the jam nuts at both ends of the linkage and rotating the linkage in the ball joints. Lengthen the linkage if the tire is turning in reverse and shorten the linkage if the tire is creeping forward. Tighten the jam nuts at both ends. Release and re- engage the neutral lock latch checking that the tire stops. Continue this process until the tire is at a dead stop.

FIGURE 14

30

Page 34 Page 36
Image 35
Page 34 Page 36
Contents For Serial Nos 670,000 & Higher Potential Hazard Exmark Parts PLUS→ Program Operators Manual Table of Contents Preparation Your Safety is InvolvedSafety Alert Symbol TrainingCarbon monoxide can kill you Potential Hazard Operation Potential Hazard Page Maintenance and Storage Riding Attachments Safety SignsPage Specifications Controls DimensionsOperation Instructions Torque RequirementsApply parking brakes whenever leaving the operators position Operating Instructions PRE-STARTPotential Hazard Rotating blades under the mower deck are dangerous Transporting Periodic Maintenance Maintenance & Adjustments102-115 N-m Page Service Interval After First 250 hrs, then yearly thereafter Page Spray Lubricant Chart Grease Lubrication ChartPage Adjustments Cutting Height Adjustment 1 2.5 cm to 4 1/4 10.8 cm Page 32 .47 cm Belt Guide Location Page Page Mower Tracks to Left or Right Trouble ShootingWaste Disposal Motor OIL DisposalEngine will not Start Blades do not Stop When DisengagedEngine Troubleshooting Engine Troubleshooting TableMower Deck Belt Routing Wiring Diagram Hydraulic Diagram Year Limited Warranty Page Service Record Fold Along Appropriate Line See EXMARK’S Complete Line of Accessories

VH15KA362, VH15KA483 specifications

The Exmark VH15KA483 and VH15KA362 are innovative models in the realm of commercial turf care, designed specifically to cater to the rigorous demands of landscape professionals. Both models are equipped with a robust engine, advanced cutting technologies, and ergonomic features that enhance both performance and user comfort.

The VH15KA483 comes with a 48-inch cutting deck, ideal for maneuvering through various types of terrain with ease. It is powered by the reliable Kohler Command Pro engine, providing ample horsepower to tackle even the toughest mowing tasks. The engine's design ensures optimal fuel efficiency while minimizing noise, making it environmentally friendly and perfect for quiet work environments.

On the other hand, the VH15KA362 features a slightly smaller 36-inch deck, making it an excellent choice for residential properties and tight spaces where precision is key. Like its counterpart, it is also equipped with a powerful Kohler engine, ensuring that mowing efficiency and performance are never compromised.

One of the standout features of both models is the patented UltraCut cutting system, which delivers a superior quality of cut that is consistent and precise. The dual-belt drive system enhances cutting speed and efficiency, allowing operators to work through larger areas quickly without sacrificing quality. Both models also incorporate a deck lift system that allows for easy adjustments, accommodating varying grass heights effortlessly.

The ergonomics of Exmark's VH series are designed with user experience in mind. The comfortable, padded seat ensures that operators can tackle long mowing sessions without fatigue. The intuitive controls are easily accessible and user-friendly, promoting a seamless mowing experience. Additionally, the compact size of the VH15KA362 makes it especially appealing to landscape professionals who need to navigate through gates and tight spaces.

For durability, both models feature a heavy-duty steel frame and components that withstand the rigors of commercial use. The powder-coated finish not only enhances the aesthetic appeal but also protects against rust and corrosion, extending the lifespan of the mower.

In summary, the Exmark VH15KA483 and VH15KA362 are versatile, powerful, and efficient mowers tailored for commercial landscaping. With advanced cutting technology, user-friendly design, and robust durability, these models represent a solid investment for any professional lawn care operator seeking performance and reliability.
Top Page Image Contents