Exmark Ultra Vac manual Belt Routing, Inch units only 60 and 72 inch units skip to step

Page 16

FIGURE 2

7.Re-install the deck drive belt in the lower groove of the double sheave. Install the plug (Item 24) into the bore of the double sheave.

8.Remove the discharge chute from the deck. Discard the mounting hardware, but save the discharge chute for use during side discharge operation. The chute pivot pin (Item 21) and hairpin (Item 22) may be stored in the pivot holes on the discharge chute during bagging operation.

52 inch units only (60 and 72 inch units skip to step 17)

9.Remove the belt guide on the blower (see Figure3)

10.Install the belt (Item 13) included in the completing kit onto the blower assembly as shown.

11.Reinstall the belt guide removed in step 9.

FIGURE 3

BELT ROUTING

12.If the Ultra Vac is being installed on a Lazer Z with a serial number less than 260,000, it is recommended to replace the steel blocker plate mounted across the bottom of the blower with the small filler plate included in the completing kit. Refer to figure on page 26, Items 48 and 49. Use the hardware that was removed when removing the large blocker plate.

Failure to install a blocker plate will create a thrown object hazard that could injure or kill bystanders, or cause property damage. This modification should not be done if the Ultra Vac blower will be mounted on a Lazer Z with a serial number of 260,000 or higher.

13.The front right deck stiffener must be trimmed for belt clearance on 52” Lazer Z units. Measure and mark the deck stiffener per Figure 4. Trim off the indicated portion of the stiffener. Touch up the trimmed area with Exmark red touchup paint – P/N 1-850337.

16

Page 15 Page 17
Image 16
Page 15 Page 17
Contents Page Potential Hazard Exmark Parts PLUS Program Effective Date September 1 ProgramOperators Manual Table of Contents Safety Safety Alert SymbolTraining PreparationSafety Signs Specifications DimensionsModel Number Bagging SystemAssembly Instructions Lazer Z HP Assembly DiagramInstall Drive KIT Install Hood Assembly and BagsInstall Blower Assembly Assemble TubesBelt Routing Assembly Instructions Lazer Z & Lazer Z XP Lazer Z Assembly Diagram Lazer Z XP Assembly Diagram Install the Hood Assembly and Bags Lazer Z units only Lazer Z XP units skip to stepLazer Z XP units only Lazer Z units continue at step Belt Routing Inch units only 60 and 72 inch units skip to step72 inch units only 52 inch units continue at step Install the Weight Plates Assemble the TubesInstall the Removable Weights RUN in 52 Units only OperationPRE-START Mowing Bagger Removal for Side DischargeTransporting Maintenance Periodic MaintenanceBelts. Service Interval 50 Hours Parts Lists DecalsBlower Assembly Lazer Z HP 44, 48, 52 & Lazer Z Blower Assembly Lazer Z HP 44, 48, 52 & Lazer Z 52 Hood and BAG Assembly Lazer Z HP 44, 48, 52, & Lazer Z Hood and BAG Assembly Lazer Z HP 44, 48, 52, & Lazer Z 52 Blower Assembly Lazer Z 60 & 72 and Lazer Z XP 60 Blower Assembly Lazer Z 60 & 72 and Lazer Z XP 60 & 72 Hood and BAG Assembly Lazer Z 60 & 72 and Lazer Z XP 60 Hood and BAG Assembly Lazer Z 60 & 72 and Lazer Z XP 60 & 72 Completing KIT Assembly Lazer Z 52, 60, & 72 Lazer Z XP 60 Lazer Lazer XP Drive KIT Assembly Lazer Z HP 44,48 Warranty Limited Warranty Exmark Commercial Turf EquipmentPage Service Record See EXMARK’S Complete Line of Products for Turf Care

Ultra Vac specifications

The Exmark Ultra Vac is a powerful and efficient vacuum system designed to streamline lawn maintenance for both professionals and homeowners. This high-performance attachment is compatible with Exmark mowers, transforming them into versatile leaf collection and debris management tools that enhance productivity and maintain a clean landscape.

One of the main features of the Exmark Ultra Vac is its robust vacuuming capability. With a large capacity collection system, this vacuum can handle a significant volume of leaves, grass clippings, and other debris, reducing the frequency of emptying during operation. The unit is equipped with a heavy-duty impeller, which provides exceptional suction power, ensuring that even wet leaves and dense clippings are effectively collected without clogging.

The Ultra Vac system is designed for easy installation and removal, making it convenient for users to switch between mowing and vacuuming modes. It integrates seamlessly with various Exmark mowers, ensuring a perfect fit that does not compromise the mower's performance. This versatility is particularly valuable for lawn care professionals who require adaptability for different tasks and conditions.

Another notable technology in the Ultra Vac is its advanced airflow design. This feature optimizes the suction flow, allowing for efficient vacuuming while maintaining the overall performance of the mower. The aerodynamic design helps to reduce noise levels, providing a quieter operation which is particularly beneficial in residential areas or noise-sensitive environments.

The Ultra Vac also boasts user-friendly features such as an adjustable chute, allowing operators to customize the height and angle of the vacuuming path. This flexibility ensures that users can effectively collect debris in various terrains and conditions. Additionally, the unit's durable construction means it can withstand the rigors of regular use, offering reliability and longevity.

Maintenance is made easy with the Ultra Vac, thanks to accessible access points and a user-friendly design. Routine checks and cleaning can be performed without requiring extensive disassembly, making it practical for busy schedules.

In summary, the Exmark Ultra Vac is a powerful, efficient, and user-friendly vacuuming system that enhances the capabilities of Exmark mowers. Its robust features, advanced technologies, and durable design make it an essential tool for anyone looking to maintain a pristine landscape with minimal effort. Whether for professional use or residential upkeep, the Ultra Vac stands out as a reliable solution for effective debris management.
Top Page Image Contents