Exmark Ultra Vac manual Lazer Z XP units only Lazer Z units continue at step

Page 15

5.Install the side plates (Items 14 and 15) loosely to the mount weldment and the wheel channels of the Lazer Z frame. The flanges on the side plates should face in towards the unit to provide the maximum tire clearance. Use the 3/8-16 x 1.00 bolts (Item 23), 3/8 spring disk washers (Item 25) and 3/8-16 whizlock nuts (Item 24). Make sure that the raised portion of the spring disk washer faces the head of the bolt. On 52 and 60 inch units, the lower bolt on the wheel channel is best installed by positioning the nut behind the hole using a deep socket and turning the bolt through the hole into the nut.

Lazer Z XP units only (Lazer Z units continue at step 8)

6.Install mount weldment (Item 9) loosely to the rear bumper using the two holes provided. Use the 3/8-16 x 1.00 bolts (Item 23), 3/8 spring disk washers (Item 25) and 3/8-16 whizlock nuts (Item 24).

7.Install the side plates (Item 16) and spacers (Item 17) loosely to the mount weldment and the mounting pads on the Lazer Z XP frame. Use the 3/8-16 x 1.00 bolts (Item 23), 3/8 spring disk washers (Item 25) and 3/8-16 whizlock nuts (Item 24). Make sure that the raised portion of the spring disk washer faces the head of the bolt.

All Units

8.Tighten all the hardware, starting with the bolts that hold the mount weldment to the rear of the unit and working forward.

9.On Lazer Z units, reinstall the rear wheels and lower the unit from the jack stands.

10.Apply a light coat of grease to the front and rear of the upper tube of the mount weldment. Install the hood assembly (Item 7) onto the mount by slipping the hook portion over the top mounting tube of the mount weldment. Secure the assembly to the mount using the clevis pins (Item 19) and hairpins (Item 20).

11.Install the bag assemblies (Item 1) by inserting the hook portion into the slots in the cross bar of the hood assembly.

4.3INSTALL BLOWER ASSEMBLY

1.Lower the deck fully. Remove the right hand belt cover. Remove the belt cover mounting stud that protrudes from the deck.

2.Remove the deck drive belt from around the right hand spindle sheave.

3.Support the right mower blade and shaft so that it will not fall out of the deck when the right sheave nut is removed.

4.Remove the right sheave nut, spring disk washer, and sheave from the spindle shaft.

NOTE: On units with wrench flats on the spindle just above the blade use a 1-inch wrench on the flat sides of the spindle shaft to prevent the spindle from turning. On units that do not have a wrench flat, block the blade rotation with a block of wood between the blade and baffles as indicated in the blade service section of the Lazer operator’s manual. Do not use the blade bolt to prevent rotation.

5.Apply a light coat of grease to the top portion of the spindle shaft where the sheave mounts.

6.Install the double sheave (Item 12) onto the right spindle shaft. Install the spring disk washer and nut removed in Step 4. Torque the sheave nut to 75-80 ft. lbs. Make sure that the spring disk washer cone is installed towards nut. See Figure 2.

NOTE: On units with wrench flats on the spindle just above the blade use a 1-inch wrench on the flat sides of the spindle shaft to prevent the spindle from turning. On units that do not have a wrench flat, block the blade rotation with a block of wood between the blade and baffles as indicated in the blade service section of the Lazer Z operator’s manual. Do not use the blade bolt to prevent rotation. Check blade bolt torque after completing this installation (115 – 120 ft. lbs.).

15

Page 14 Page 16
Image 15
Page 14 Page 16
Contents Page Potential Hazard Effective Date September 1 Program Exmark Parts PLUS ProgramOperators Manual Table of Contents Preparation SafetySafety Alert Symbol TrainingSafety Signs Bagging System SpecificationsDimensions Model NumberAssembly Diagram Assembly Instructions Lazer Z HPAssemble Tubes Install Drive KITInstall Hood Assembly and Bags Install Blower AssemblyBelt Routing Assembly Instructions Lazer Z & Lazer Z XP Lazer Z Assembly Diagram Lazer Z XP Assembly Diagram Lazer Z units only Lazer Z XP units skip to step Install the Hood Assembly and BagsLazer Z XP units only Lazer Z units continue at step Inch units only 60 and 72 inch units skip to step Belt Routing72 inch units only 52 inch units continue at step Assemble the Tubes Install the Weight PlatesInstall the Removable Weights Operation RUN in 52 Units onlyPRE-START Bagger Removal for Side Discharge MowingTransporting Periodic Maintenance MaintenanceBelts. Service Interval 50 Hours Decals Parts ListsBlower Assembly Lazer Z HP 44, 48, 52 & Lazer Z Blower Assembly Lazer Z HP 44, 48, 52 & Lazer Z 52 Hood and BAG Assembly Lazer Z HP 44, 48, 52, & Lazer Z Hood and BAG Assembly Lazer Z HP 44, 48, 52, & Lazer Z 52 Blower Assembly Lazer Z 60 & 72 and Lazer Z XP 60 Blower Assembly Lazer Z 60 & 72 and Lazer Z XP 60 & 72 Hood and BAG Assembly Lazer Z 60 & 72 and Lazer Z XP 60 Hood and BAG Assembly Lazer Z 60 & 72 and Lazer Z XP 60 & 72 Completing KIT Assembly Lazer Z 52, 60, & 72 Lazer Z XP 60 Lazer Lazer XP Drive KIT Assembly Lazer Z HP 44,48 Limited Warranty Exmark Commercial Turf Equipment WarrantyPage Service Record See EXMARK’S Complete Line of Products for Turf Care

Ultra Vac specifications

The Exmark Ultra Vac is a powerful and efficient vacuum system designed to streamline lawn maintenance for both professionals and homeowners. This high-performance attachment is compatible with Exmark mowers, transforming them into versatile leaf collection and debris management tools that enhance productivity and maintain a clean landscape.

One of the main features of the Exmark Ultra Vac is its robust vacuuming capability. With a large capacity collection system, this vacuum can handle a significant volume of leaves, grass clippings, and other debris, reducing the frequency of emptying during operation. The unit is equipped with a heavy-duty impeller, which provides exceptional suction power, ensuring that even wet leaves and dense clippings are effectively collected without clogging.

The Ultra Vac system is designed for easy installation and removal, making it convenient for users to switch between mowing and vacuuming modes. It integrates seamlessly with various Exmark mowers, ensuring a perfect fit that does not compromise the mower's performance. This versatility is particularly valuable for lawn care professionals who require adaptability for different tasks and conditions.

Another notable technology in the Ultra Vac is its advanced airflow design. This feature optimizes the suction flow, allowing for efficient vacuuming while maintaining the overall performance of the mower. The aerodynamic design helps to reduce noise levels, providing a quieter operation which is particularly beneficial in residential areas or noise-sensitive environments.

The Ultra Vac also boasts user-friendly features such as an adjustable chute, allowing operators to customize the height and angle of the vacuuming path. This flexibility ensures that users can effectively collect debris in various terrains and conditions. Additionally, the unit's durable construction means it can withstand the rigors of regular use, offering reliability and longevity.

Maintenance is made easy with the Ultra Vac, thanks to accessible access points and a user-friendly design. Routine checks and cleaning can be performed without requiring extensive disassembly, making it practical for busy schedules.

In summary, the Exmark Ultra Vac is a powerful, efficient, and user-friendly vacuuming system that enhances the capabilities of Exmark mowers. Its robust features, advanced technologies, and durable design make it an essential tool for anyone looking to maintain a pristine landscape with minimal effort. Whether for professional use or residential upkeep, the Ultra Vac stands out as a reliable solution for effective debris management.
Top Page Image Contents