Exmark Ultra Vac manual Install Drive KIT, Install Hood Assembly and Bags, Assemble Tubes

Page 10

3.2 INSTALL DRIVE KIT

1.Install drive kit (PN 103-1313, 103-1314, 103-1315, or 103-1317 depending on deck size) per the instructions included in the kit.

NOTE: The original belt shield stud must be removed for belt clearance.

3.3INSTALL HOOD ASSEMBLY AND BAGS

44and 48 inch units (52 inch units skip to step 3)

Note: When installing Ultra Vac on Lazer Z HP model LHP4818KC with serial numbers below 176621, refer to additional necessary instructions included in adapter kit 103-0328.

1.Remove and discard the (8) bolts that retain the “HOT” engine guard shield (Item 1). Keep the nuts for use in Step 2.

2.Install the Bagger Mount Weldment (Item 2) and engine guard shield using the 5/16-18 x 1 Screws provided (Item 3) and whizlock nuts removed in step 1. Continue at step 6.

52 inch units

3.Remove and discard the (8) bolts that retain the rear weight (Item 12). Keep the whizlock nuts for use in step 5.

4.Install the Bagger Mount Weldment (Item 2) to the rear of the frame using (4) 5/16 – 18 X1.00 screws (Item 3) and (4) 5/16 – 18 whizlock nuts (Item 15). Use only the bottom four holes on the Bagger Mount Weldment

5.Install the Rear Weight (Item 12) and spacer (Item 13) from the drive kit using the (8) 5/16

– 18 X1.75 screws (Item 14) and whizlock nuts removed in step 3.

All units

6.Slide tube ends of Hood Assembly (Item 4) into the tubes of the mount weldment. Install

(2) clevis pins (Item 16) through holes in tubes. Retain with (2) Hair Pins (Item 17).

7.Hang the (2) Bag Assemblies (Item 5) from the slots in the Bagger Upright. Close and latch hood.

3.4ASSEMBLE TUBES

Note: When installing Ultra Vac on Lazer Z HP model LHP4818KC with serial number below 176621, refer to additional necessary instructions included in adapter kit 103-0328.

1.Assemble the Upper (Item 6) and Lower (Item 7) Tubes using the (3) #10-24 x .75 Truss head Screws (Item 8), (3) #10 washers (Item 9), and (3) #10-24 Nyloc Nuts (Item 10). Screw head should be installed to the inside of the tube to provide minimum obstruction to flow. Make sure the hole with the arrow on the Upper Tube aligns with the dimple in the Lower Tube to place the turnout on the Upper Tube in the correct position.

For units with a 44” deck: Slide Upper Tube over Lower Tube until edge of Upper Tube matches up with dimple in Lower Tube labeled 44.

For units with a 48” & 52” deck: Slide Upper Tube over Lower Tube until edge of Upper Tube matches up with dimple in Lower Tube labeled 48, 52.

3.5INSTALL BLOWER ASSEMBLY

1.Remove the belt guide on the blower (Item 11). (See Figure 1)

2.Install the belt (from the Drive Kit) onto the Blower Assembly (Item 11) as shown.

10

Page 9 Page 11
Image 10
Page 9 Page 11
Contents Page Potential Hazard Exmark Parts PLUS Program Effective Date September 1 ProgramOperators Manual Table of Contents Training SafetySafety Alert Symbol PreparationSafety Signs Model Number SpecificationsDimensions Bagging SystemAssembly Instructions Lazer Z HP Assembly DiagramInstall Blower Assembly Install Drive KITInstall Hood Assembly and Bags Assemble TubesBelt Routing Assembly Instructions Lazer Z & Lazer Z XP Lazer Z Assembly Diagram Lazer Z XP Assembly Diagram Install the Hood Assembly and Bags Lazer Z units only Lazer Z XP units skip to stepLazer Z XP units only Lazer Z units continue at step Belt Routing Inch units only 60 and 72 inch units skip to step72 inch units only 52 inch units continue at step Install the Weight Plates Assemble the TubesInstall the Removable Weights RUN in 52 Units only OperationPRE-START Mowing Bagger Removal for Side DischargeTransporting Maintenance Periodic MaintenanceBelts. Service Interval 50 Hours Parts Lists DecalsBlower Assembly Lazer Z HP 44, 48, 52 & Lazer Z Blower Assembly Lazer Z HP 44, 48, 52 & Lazer Z 52 Hood and BAG Assembly Lazer Z HP 44, 48, 52, & Lazer Z Hood and BAG Assembly Lazer Z HP 44, 48, 52, & Lazer Z 52 Blower Assembly Lazer Z 60 & 72 and Lazer Z XP 60 Blower Assembly Lazer Z 60 & 72 and Lazer Z XP 60 & 72 Hood and BAG Assembly Lazer Z 60 & 72 and Lazer Z XP 60 Hood and BAG Assembly Lazer Z 60 & 72 and Lazer Z XP 60 & 72 Completing KIT Assembly Lazer Z 52, 60, & 72 Lazer Z XP 60 Lazer Lazer XP Drive KIT Assembly Lazer Z HP 44,48 Warranty Limited Warranty Exmark Commercial Turf EquipmentPage Service Record See EXMARK’S Complete Line of Products for Turf Care

Ultra Vac specifications

The Exmark Ultra Vac is a powerful and efficient vacuum system designed to streamline lawn maintenance for both professionals and homeowners. This high-performance attachment is compatible with Exmark mowers, transforming them into versatile leaf collection and debris management tools that enhance productivity and maintain a clean landscape.

One of the main features of the Exmark Ultra Vac is its robust vacuuming capability. With a large capacity collection system, this vacuum can handle a significant volume of leaves, grass clippings, and other debris, reducing the frequency of emptying during operation. The unit is equipped with a heavy-duty impeller, which provides exceptional suction power, ensuring that even wet leaves and dense clippings are effectively collected without clogging.

The Ultra Vac system is designed for easy installation and removal, making it convenient for users to switch between mowing and vacuuming modes. It integrates seamlessly with various Exmark mowers, ensuring a perfect fit that does not compromise the mower's performance. This versatility is particularly valuable for lawn care professionals who require adaptability for different tasks and conditions.

Another notable technology in the Ultra Vac is its advanced airflow design. This feature optimizes the suction flow, allowing for efficient vacuuming while maintaining the overall performance of the mower. The aerodynamic design helps to reduce noise levels, providing a quieter operation which is particularly beneficial in residential areas or noise-sensitive environments.

The Ultra Vac also boasts user-friendly features such as an adjustable chute, allowing operators to customize the height and angle of the vacuuming path. This flexibility ensures that users can effectively collect debris in various terrains and conditions. Additionally, the unit's durable construction means it can withstand the rigors of regular use, offering reliability and longevity.

Maintenance is made easy with the Ultra Vac, thanks to accessible access points and a user-friendly design. Routine checks and cleaning can be performed without requiring extensive disassembly, making it practical for busy schedules.

In summary, the Exmark Ultra Vac is a powerful, efficient, and user-friendly vacuuming system that enhances the capabilities of Exmark mowers. Its robust features, advanced technologies, and durable design make it an essential tool for anyone looking to maintain a pristine landscape with minimal effort. Whether for professional use or residential upkeep, the Ultra Vac stands out as a reliable solution for effective debris management.
Top Page Image Contents