Exmark Cd42cd, Cd48cd, CD42CD manual Adjustments, Gearbox OIL Drain Locations

Page 16

n)Re-install the seal guards over the wheel hub and insert wheel into caster fork. Re-install caster bolt and tighten nut fully.

IMPORTANT: To prevent seal and bearing damage, check the bearing adjustment often. Spin the caster tire. The tire should not spin freely (more than 1 or 2 revolutions) or have any side play. If the wheel spins freely, adjust torque on spacer nut until there is a slight amount of drag. Re-apply thread locking adhesive.

c)Lubricate switch actuator rod with spray type lubricant or light oil.

4.2.7Change gearbox oil:

Change oil in all 3 gearbox housings after first 50 hrs of operation. Check every 100 hours thereafter. Add oil as needed until level with oil drain plug.

a)Stop engine, wait for all moving parts to stop, and remove key.

b)Place unit on a level surface.

c)Remove the gearbox and drive shaft assembly from the mower deck. Retain hardware for re-use.

d)Remove the large oil drain plug on the front of each of the 3 gearboxes and drain oil. See Figure 9.

e)Remove small magnetic plugs and wipe away any material accumulated on the plugs. See Figure 9.

FIGURE 9

GEARBOX OIL DRAIN LOCATIONS

f)Apply a Teflon pipe sealant to all small magnetic plugs and re-install into the gearbox.

g)Re-install the gearbox and drive shaft assembly to the mower deck.

h)Fill gearbox with Mobil 1 75W-90 gear lube oil until level with oil drain plug.

NOTE: Mower deck should remain level to the ground when filling gearbox with oil. Do not fill gearbox with deck raised in the service position.

i)Apply a Teflon pipe sealant to the 3 large oil plugs and re-install into the gearbox.

4.2.8Thread locking adhesives such as “Loctite 242” or “Fel-Pro, Pro-Lock Nut Type” are used on the following fasteners:

a)Caster wheel spacer nuts.

4.3 ADJUSTMENTS

IMPORTANT: Disengage PTO, shut off engine, wait for all moving parts to stop, and remove key before servicing, cleaning, or making any adjustments to the unit.

4.3.1Cutting Height Adjustment:

a)Stop engine, wait for all moving parts to stop, and remove key.

b)Move cotter pins on four deck support pins to proper hole for height of cut desired.

11

Page 15 Page 17
Image 16
Page 15 Page 17
Contents For Serial Nos 510,000 & Higher Exmark Parts PLUS→ Program Effective Date September 1 ProgramPotential Hazard Operators Manual Table of Contents Safety Your Safety is InvolvedSafety Alert Symbol TrainingSafety Signs Maintenance and StorageOperation Page Specifications Assembly InstructionsPTO Guard Installation Push ARM InstallationJackshaft and Drive Shaft Connection Deck Spring Installation Maintenance & AdjustmentsDeck Removal Deck Raising and Lowering Raising the DeckPeriodic Maintenance Service Interval DailyBlade Bolt Installation Service Interval Refer to chartGrease Fitting Lubrication Chart Service Interval Once YearlyAdjustments Gearbox OIL Drain LocationsCaster Adjustment Deck Support PIN AssemblyDeck Locking PIN Adjustment Parts List Deck GroupDeck Group Front Frame Group Front Frame Group Gearbox Components for 103-3460 Year Limited Warranty Riding Accessories Walk Behind Accessories

CD42CD, Cd42cd, Cd48cd specifications

The Exmark CD42CD and CD48CD series stand out in the mowing equipment market, designed specifically for commercial landscaping professionals seeking efficiency and performance. These zero-turn mowers encapsulate advanced technologies and features that deliver a superior mowing experience.

One of the primary features of the CD42CD and CD48CD models is their powerful engines. These mowers are equipped with robust, gasoline-powered engines that provide ample horsepower, ensuring they can tackle even the toughest grass and terrain with ease. The mowers’ compact design, particularly the 42-inch and 48-inch cutting decks, allows for impressive maneuverability, making them ideal for tight spaces and intricate landscaping tasks.

The cutting decks of the Exmark CD series are crafted for precision. With a deep design, these decks enable efficient airflow, ensuring that grass is cut evenly and finely. Users appreciate the enhanced cut quality, which not only provides a more aesthetically pleasing lawn but also promotes healthier grass growth. The cutting heights are adjustable, allowing operators to achieve their desired length for various grass types and conditions.

Another significant technology embedded in the Exmark CD series is the patented Innovate technology, which improves both the efficiency of the mower and the ease of operation. This technology allows for smoother handling and better traction, leading to reduced overall fuel consumption. Moreover, the ergonomic controls make it easier for operators to navigate with precision.

In terms of durability, the Exmark CD series is built with rugged components that withstand the demands of daily commercial use. The frame is robust, and the wheels are designed for optimal stability and traction, contributing to a long service life.

Comfort is also a priority in the CD42CD and CD48CD models. The operator’s seat is designed for long hours of use, featuring ample cushioning and support. Adjustable armrests and controls align with the operator's body, minimizing fatigue during extensive mowing sessions.

In summary, the Exmark CD42CD and CD48CD are a testament to innovative design in landscape maintenance equipment. Their powerful performance, cutting-edge technology, and user-oriented features further solidify their reputation as reliable tools for professional landscapers aiming to enhance productivity and achieve exceptional results in their mowing tasks.
Top Page Image Contents