Exmark CD42CD, Cd42cd, Cd48cd manual Grease Fitting Lubrication Chart, Service Interval Once Yearly

Page 15

GREASE FITTING LUBRICATION CHART

 

FITTING

INITIAL

NO. of

SERVICE

 

LOCATIONS

PUMPS

PLACES

INTERVAL

1.

Drive Shaft

1

3

40 hours

2.

Front Caster Wheel Hub

1

2

8 hours

3.

Deck Flip-Up

1

4

100 hours

4.

Push Arm Tubes

1

2

100 hours

5.

Caster Pivots

*0

3

*yearly

∗ See Section 4.2.5 c) for special lubrication instructions on the front caster pivots and Section 5.2.6 for special lubrication instructions on the rear caster wheel hub.

c)Lubricate caster pivots once a year. Remove hex plug and cap. Thread grease zerk in hole and pump with grease until it oozes out around top bearing. Remove grease zerk and thread plug back in. Place cap back on.

4.2.6Lubricate caster wheel hub:

Service Interval: Once Yearly

a)Stop engine, wait for all moving parts to stop, and remove key.

b)Remove caster wheel from caster forks.

c)Remove seal guards from the wheel hub.

d) Remove one of the spacer nuts from the

 

axle assembly in the caster wheel. Note

 

that thread locking adhesive has been

 

applied to lock the spacer nuts to the axle.

 

Remove the axle (with the other spacer

 

nut still assembled to it) from the wheel

FIGURE 8

assembly.

CASTER WHEEL ASSEMBLY

 

e)Pry out seals, and inspect bearings for wear or damage and replace if necessary.

f)Pack the bearings with a NGLI grade #1 multi-purpose grease.

g)Insert (1) bearing, (1) new seal into the wheel.

NOTE: Seals (Exmark PN 103-0063) must be replaced.

h)If the axle assembly has had both spacer nuts removed (or broken loose), apply a thread locking adhesive to (1) spacer nut and thread onto the axle with the wrench flats facing outward. Do not thread spacer nut all of the way onto the end of the axle. Leave approximately 1/8” (3 mm) from the outer surface of the spacer nut to the end of the axle inside the nut.

i)Insert the assembled nut and axle into the wheel on the side of the wheel with the new seal and bearing.

j)With the open end of the wheel facing up, fill the area inside the wheel around the axle full of NGLI grade #1 multi-purpose grease.

k)Insert the second bearing and new seal into the wheel.

l)Apply a thread locking adhesive to the 2nd spacer nut and thread onto the axle with the wrench flats facing outward.

m)Torque the nut to 75-80 in-lbs. (8-9 N-m), loosen, then re-torque to 20-25 in-lbs. (2-3 N-m). Make sure axle does not extend beyond either nut.

10

Page 14 Page 16
Image 15
Page 14 Page 16
Contents For Serial Nos 510,000 & Higher Effective Date September 1 Program Exmark Parts PLUS→ ProgramPotential Hazard Operators Manual Table of Contents Training SafetyYour Safety is Involved Safety Alert SymbolMaintenance and Storage Safety SignsOperation Page Assembly Instructions SpecificationsPush ARM Installation PTO Guard InstallationJackshaft and Drive Shaft Connection Maintenance & Adjustments Deck Spring InstallationDeck Removal Raising the Deck Deck Raising and LoweringService Interval Daily Periodic MaintenanceService Interval Refer to chart Blade Bolt InstallationService Interval Once Yearly Grease Fitting Lubrication ChartGearbox OIL Drain Locations AdjustmentsDeck Support PIN Assembly Caster AdjustmentDeck Locking PIN Adjustment Deck Group Parts ListDeck Group Front Frame Group Front Frame Group Gearbox Components for 103-3460 Year Limited Warranty Walk Behind Accessories Riding Accessories

CD42CD, Cd42cd, Cd48cd specifications

The Exmark CD42CD and CD48CD series stand out in the mowing equipment market, designed specifically for commercial landscaping professionals seeking efficiency and performance. These zero-turn mowers encapsulate advanced technologies and features that deliver a superior mowing experience.

One of the primary features of the CD42CD and CD48CD models is their powerful engines. These mowers are equipped with robust, gasoline-powered engines that provide ample horsepower, ensuring they can tackle even the toughest grass and terrain with ease. The mowers’ compact design, particularly the 42-inch and 48-inch cutting decks, allows for impressive maneuverability, making them ideal for tight spaces and intricate landscaping tasks.

The cutting decks of the Exmark CD series are crafted for precision. With a deep design, these decks enable efficient airflow, ensuring that grass is cut evenly and finely. Users appreciate the enhanced cut quality, which not only provides a more aesthetically pleasing lawn but also promotes healthier grass growth. The cutting heights are adjustable, allowing operators to achieve their desired length for various grass types and conditions.

Another significant technology embedded in the Exmark CD series is the patented Innovate technology, which improves both the efficiency of the mower and the ease of operation. This technology allows for smoother handling and better traction, leading to reduced overall fuel consumption. Moreover, the ergonomic controls make it easier for operators to navigate with precision.

In terms of durability, the Exmark CD series is built with rugged components that withstand the demands of daily commercial use. The frame is robust, and the wheels are designed for optimal stability and traction, contributing to a long service life.

Comfort is also a priority in the CD42CD and CD48CD models. The operator’s seat is designed for long hours of use, featuring ample cushioning and support. Adjustable armrests and controls align with the operator's body, minimizing fatigue during extensive mowing sessions.

In summary, the Exmark CD42CD and CD48CD are a testament to innovative design in landscape maintenance equipment. Their powerful performance, cutting-edge technology, and user-oriented features further solidify their reputation as reliable tools for professional landscapers aiming to enhance productivity and achieve exceptional results in their mowing tasks.
Top Page Image Contents