Exmark 4501-191 Rev.A manual Positioning the Seat, Inch Deck

Page 25

Operation

the positions shown in Figure 15. Rollers will maintain 3/4 inches (19 mm) clearance to the ground to minimize gouging and roller wear or damage.

Note: For Maximum Deck Flotation, place the rollers one hole position lower. Rollers should maintain 1/4 inch (6.35 mm) clearance to the ground. Do Not adjust rollers to support the deck.

Figure 14

42 Inch Deck

1.Anti-scalp roller mounting bracket

2.Below 2 1/2 inches (64mm) cutting height

3.2 1/2 inches (64mm) and above cutting height

Figure 15

50 Inch Deck

For cutting heights above 3 1/2 inches (90 mm)

use the bottom hole. The rollers will still be effective

 

against scalping.

1. Anti-scalp roller

2. Cutting height

mounting bracket

7.Torque hardware to 27-33 ft-lb (37-45 N-m) or loss of roller may result.

Positioning the Seat

The seat can move forward and backward. Position the seat where you have the best control of the machine and are most comfortable.

• 42 Inch Unit:

1.Tip the seat forward.

2.Loosen the adjustment bolts.

Figure 16

1.Adjustment bolt

3.Move the seat to the desired position and tighten bolts.

4.Tip the seat back to the closed position.

•50 Inch Units:

1.Push the adjustment lever towards the center of the machine to release the seat adjuster track (Figure 17).

Figure 17

1.Adjustment lever

2.Move the seat to the desired position and release the lever to lock in that position.

25

Page 24 Page 26
Image 25
Page 24 Page 26
Contents Quest California Introduction Contents Safety Alert Symbol SafetySafe Operating Practices General OperationSlope Operation ServiceChildren TowingGeneral Service Exmark Riding Mower SafetySafety 106-8717 Safety and Instructional Decals119-8814 PTO Switch Symbols 116-4220 120-2239 Model Numbers SpecificationsSystems Dimensions Torque Requirements Product OverviewControls OperationOperating Instructions Think Safety FirstHeight-of-Cut Foot Lever Fuel WindowRecommended Gasoline Using Stabilizer/ConditionerStarting the Engine Checking the Engine Oil LevelFilling the Fuel Tank Stopping the Engine Operating the BladesEngaging the Blades Disengaging the BladesUnderstanding the Safety Interlock System Safety Interlock SystemTesting the Safety Interlock System Driving Forward or BackwardBackward Adjusting the Anti-Scalp Rollers Adjusting the Height of CutStopping the Machine Inch Deck Positioning the SeatChanging the Seat Ride Suspension Adjusting the Motion Control LeversPushing the Machine by Hand Transporting Side DischargeTo Operate the Machine Transporting a UnitOperating Tips Keep the Underside of the Mower Clean When StoppingBlade Maintenance Long GrassRecommended Maintenance Schedules MaintenanceLubrication Raising the SeatGreasing the Bearings Servicing the Air Cleaner Engine MaintenanceCleaning the Element Servicing the Engine OilChanging the Oil and Filter Servicing the Spark Plug Installing the Spark PlugRemoving the Spark Plug Checking the Spark PlugFuel System Maintenance Cleaning the Blower HousingServicing the Emissions Filter Replacing the Fuel FilterCharging the Battery Electrical System MaintenanceRemoving the Battery Recommended Jump Starting Procedure Checking the Battery ChargeDo Not jump start a weak battery if these conditions exist Installing the BatteryServicing the Fuses Drive System Maintenance Checking the Tire PressureReleasing the Electric Brake Checking the Hydraulic Oil LevelRemoving Hydraulic System Filters Changing the Hydraulic System Filter and OilInstalling the Hydraulic System Filters Bleeding the Hydraulic System Mower Maintenance Servicing the Cutting BladesBefore Inspecting or Servicing the Blades Inspecting the BladesMeasure from the tip of the blade to the flat surface here Checking for Bent BladesSharpening the Blades Removing the BladesLeveling the Mower Deck Installing the BladesSide-to-Side Leveling Blades side to side Adjusting the Front-to-Rear Blade Slope Removing the Mower Mower Belt MaintenanceInspecting the Belts Replacing the Mower BeltInstalling the Mower Deflector Replacing the DischargeRod Deck brackets Spring Washing the Underside of the Mower Clean Engine and Exhaust System AreaStorage Cleaning and StorageProblem Possible Cause Corrective Action TroubleshootingTo Pushing the Machine by Hand Electrical Diagram SchematicsElectrical Logic Schematic Exmark Quest Turf Equipment Page Page Date Description of Work Done Service Done By Service RecordPage This page may be copied for personal use Exmark Accessories and Options

4501-191 Rev.A specifications

The Exmark 4501-191 Rev.A is a cutting-edge lawn mower designed to deliver exceptional performance and efficiency for both residential and commercial users. With its robust build and advanced technology, this model has quickly gained popularity among landscapers and homeowners alike.

One of the standout features of the Exmark 4501-191 Rev.A is its powerful engine. Equipped with a high-performance Kohler engine, this mower provides ample horsepower and torque, ensuring efficient cutting even in tough conditions. This allows users to tackle dense grass and uneven terrains with ease, making it ideal for various landscaping needs.

The mower's innovative cutting system is another highlight that sets it apart. Featuring a large, durable cutting deck, the Exmark 4501-191 Rev.A offers an impressive cutting width, enabling users to cover more ground in less time. The deck is designed for precision, providing a clean and even cut every time. Additionally, the adjustable cutting height feature allows for customized lawn care, accommodating different grass types and lengths.

One of the remarkable technologies integrated into the Exmark 4501-191 Rev.A is its efficient fuel system. The mower is engineered to maximize fuel efficiency, allowing users to extend their mowing sessions without the frequent need to refuel. This feature not only saves time but also reduces overall operating costs, making the mower a cost-effective choice for users with large properties.

Comfort and maneuverability are also key characteristics of the Exmark 4501-191 Rev.A. The ergonomic controls are designed for ease of use, providing a smooth and responsive experience. The mower features large rear wheels and front casters, allowing for agile navigation around obstacles and tight spaces. This is particularly beneficial for commercial users who often work in complex environments.

Maintenance is simplified with the Exmark 4501-191 Rev.A, allowing users to focus on lawn care rather than upkeep. The model is built with durable materials, ensuring longevity and reducing wear and tear. Clear access points for cleaning and maintenance further enhance user convenience, making it easy to keep the mower in top shape.

In summary, the Exmark 4501-191 Rev.A is a high-performance lawn mower that combines power, efficiency, and ease of use. With its advanced engine, innovative cutting system, and user-friendly design, it stands out as an excellent choice for anyone looking to achieve a beautifully manicured lawn. Whether for commercial or residential use, this mower is a reliable tool that promises exceptional results.
Top Page Image Contents