Exmark 4501-191 Rev.A manual Installing the Hydraulic System Filters

Page 41

Maintenance

Installing the Hydraulic System Filters

 

 

Figure 37

 

 

 

Right side shown

1.

Transaxle drive

4.

Screws

2.

Oil filter

5.

Vent plug

3.Filter guard

5.Carefully clean area around filters. It is important that no dirt or contamination enter hydraulic system.

6.Place a container below the filter to catch the oil that drains when the filter and vent plugs are removed.

7.Locate and remove the vent plug on each transmission

8.Unscrew the filter to remove and allow oil to drain from drive system.

Repeat this procedure for both filters.

Figure 38

1.Apply a thin coat of oil on the surface of the rubber seal of each filter.

2.Turn the filter clockwise until rubber seal contacts the filter adapter then tighten the filter an additional 3/4 to 1 full turn. Repeat for the other filter

3.Install the filter guards over each filter as previously removed. Use the three screws to secure the filter guards.

4.Verify the vent plugs are removed before adding the oil.

5.Slowly pour the specified oil through expansion reservoir until oil comes out of one of the vent plug holes. Stop and install that vent plug. Torque the plug to 180 in-lb (20.3 N-m).

6.Continue to add oil through the expansion reservoir until oil comes out of the remaining vent plug hole on the second transmission. Stop

41

Page 40 Page 42
Image 41
Page 40 Page 42
Contents Quest California Introduction Contents Safety Alert Symbol SafetySafe Operating Practices General OperationSlope Operation ServiceChildren TowingGeneral Service Exmark Riding Mower SafetySafety 106-8717 Safety and Instructional Decals119-8814 PTO Switch Symbols 116-4220 120-2239 Systems SpecificationsModel Numbers Dimensions Torque Requirements Product OverviewControls OperationOperating Instructions Think Safety FirstHeight-of-Cut Foot Lever Fuel WindowRecommended Gasoline Using Stabilizer/ConditionerFilling the Fuel Tank Checking the Engine Oil LevelStarting the Engine Stopping the Engine Operating the BladesEngaging the Blades Disengaging the BladesUnderstanding the Safety Interlock System Safety Interlock SystemTesting the Safety Interlock System Driving Forward or BackwardBackward Stopping the Machine Adjusting the Height of CutAdjusting the Anti-Scalp Rollers Inch Deck Positioning the SeatPushing the Machine by Hand Adjusting the Motion Control LeversChanging the Seat Ride Suspension Transporting Side DischargeTo Operate the Machine Transporting a UnitOperating Tips Keep the Underside of the Mower Clean When StoppingBlade Maintenance Long GrassRecommended Maintenance Schedules MaintenanceGreasing the Bearings Raising the SeatLubrication Servicing the Air Cleaner Engine MaintenanceCleaning the Element Servicing the Engine OilChanging the Oil and Filter Servicing the Spark Plug Installing the Spark PlugRemoving the Spark Plug Checking the Spark PlugFuel System Maintenance Cleaning the Blower HousingServicing the Emissions Filter Replacing the Fuel FilterRemoving the Battery Electrical System MaintenanceCharging the Battery Recommended Jump Starting Procedure Checking the Battery ChargeDo Not jump start a weak battery if these conditions exist Installing the BatteryServicing the Fuses Drive System Maintenance Checking the Tire PressureReleasing the Electric Brake Checking the Hydraulic Oil LevelRemoving Hydraulic System Filters Changing the Hydraulic System Filter and OilInstalling the Hydraulic System Filters Bleeding the Hydraulic System Mower Maintenance Servicing the Cutting BladesBefore Inspecting or Servicing the Blades Inspecting the BladesMeasure from the tip of the blade to the flat surface here Checking for Bent BladesSharpening the Blades Removing the BladesSide-to-Side Leveling Installing the BladesLeveling the Mower Deck Blades side to side Adjusting the Front-to-Rear Blade Slope Removing the Mower Mower Belt MaintenanceInspecting the Belts Replacing the Mower BeltInstalling the Mower Deflector Replacing the DischargeRod Deck brackets Spring Washing the Underside of the Mower Clean Engine and Exhaust System AreaStorage Cleaning and StorageProblem Possible Cause Corrective Action TroubleshootingTo Pushing the Machine by Hand Electrical Diagram SchematicsElectrical Logic Schematic Exmark Quest Turf Equipment Page Page Date Description of Work Done Service Done By Service RecordPage This page may be copied for personal use Exmark Accessories and Options

4501-191 Rev.A specifications

The Exmark 4501-191 Rev.A is a cutting-edge lawn mower designed to deliver exceptional performance and efficiency for both residential and commercial users. With its robust build and advanced technology, this model has quickly gained popularity among landscapers and homeowners alike.

One of the standout features of the Exmark 4501-191 Rev.A is its powerful engine. Equipped with a high-performance Kohler engine, this mower provides ample horsepower and torque, ensuring efficient cutting even in tough conditions. This allows users to tackle dense grass and uneven terrains with ease, making it ideal for various landscaping needs.

The mower's innovative cutting system is another highlight that sets it apart. Featuring a large, durable cutting deck, the Exmark 4501-191 Rev.A offers an impressive cutting width, enabling users to cover more ground in less time. The deck is designed for precision, providing a clean and even cut every time. Additionally, the adjustable cutting height feature allows for customized lawn care, accommodating different grass types and lengths.

One of the remarkable technologies integrated into the Exmark 4501-191 Rev.A is its efficient fuel system. The mower is engineered to maximize fuel efficiency, allowing users to extend their mowing sessions without the frequent need to refuel. This feature not only saves time but also reduces overall operating costs, making the mower a cost-effective choice for users with large properties.

Comfort and maneuverability are also key characteristics of the Exmark 4501-191 Rev.A. The ergonomic controls are designed for ease of use, providing a smooth and responsive experience. The mower features large rear wheels and front casters, allowing for agile navigation around obstacles and tight spaces. This is particularly beneficial for commercial users who often work in complex environments.

Maintenance is simplified with the Exmark 4501-191 Rev.A, allowing users to focus on lawn care rather than upkeep. The model is built with durable materials, ensuring longevity and reducing wear and tear. Clear access points for cleaning and maintenance further enhance user convenience, making it easy to keep the mower in top shape.

In summary, the Exmark 4501-191 Rev.A is a high-performance lawn mower that combines power, efficiency, and ease of use. With its advanced engine, innovative cutting system, and user-friendly design, it stands out as an excellent choice for anyone looking to achieve a beautifully manicured lawn. Whether for commercial or residential use, this mower is a reliable tool that promises exceptional results.
Top Page Image Contents