Exmark M216KA, M216KASP manual Before Starting, Filling the Crankcase with Oil, Oil Capacity

Page 12

2.

Since the plug is slightly wider than the discharge

 

tunnel opening, rotate the plug clockwise slightly

 

while inserting it (Fig. 5).

 

Note: Ensure that the arrow on the plug decal points

 

upward.

3.

Push the plug all the way in until the spring clip on the

Before each use, ensure that the oil level is between the Add and Full marks on the dipstick (Fig. 7).

bottom of the plug clicks into place, locking the plug

securely into the discharge tunnel (Fig. 6).

2

3

1.Dipstick

2.Full

1

m-7277

m-7278

Figure 7

3. Add

1

m-1915

Figure 6

1. Spring clip

4.Release the discharge door handle to lock the top of the plug.

Before Starting

Filling the Crankcase with Oil

Initially, fill the crankcase with 30 ounces (0.88 liters) of oil. Use only high-quality SAE 30 or SAE 10W30 weight detergent oil that has the American Petroleum Institute (API) service classification SF, SG, SH, or SJ.

 

Oil Capacity

 

 

 

With Oil Filter

 

30 ounces (0.88 L)

 

 

 

Without Oil Filter

 

24 ounces (0.70 L)

 

 

 

Note: When the crankcase is empty, pour about 3/4 of the crankcase capacity of oil in the crankcase, then follow the procedure in this section.

To add oil:

1.Move the lawn mower to a level surface.

2.Clean around the dipstick (Fig. 7).

3.Remove the dipstick by rotating the cap counterclockwise and pulling it out.

4.Wipe the dipstick clean with a clean cloth.

5.Insert the dipstick into the filler neck, then remove it.

Note: To ensure an accurate oil level reading, you must fully install the dipstick.

6.Read the oil level on the dipstick (Fig. 7).

7.If the oil level reading is below the Add mark on the dipstick, slowly pour only enough oil into the filler hole to raise the oil level to the Full mark on the dipstick.

Important Do not overfill the crankcase with oil and run the engine; engine damage will result. Drain the excess oil until the oil level on the dipstick reads Full.

8.Insert the dipstick into the filler neck and rotate the cap clockwise until it is tight.

8

Image 12
Contents M216KA / M216KASP Potential Hazard Exmark Parts PLUS Program Operators Manual Contents Specifications SafetyGeneral Lawn Mower Safety IntroductionPreparation OperationExmark Lawn Mower Safety Maintenance and StorageGeneral Operation Safety and Instruction Decals Assembly Installing the HandleInstalling the Starter Rope Installing the Fuel Tank and the Fuel LineInstalling the Discharge Tunnel Plug Before Starting Filling the Crankcase with OilOil Capacity Filling the Fuel Tank with Gasoline Keep it out of the reach of childrenNever buy more than a 30-day supply GasolineOperation ControlsStarting the Engine Stopping the EngineUsing the Discharge Tunnel Plug Adjusting the Cutting HeightOperating the Blade and the Self-Propel Drive Using the Grass Bag Installing the Grass BagMowing with the Grass Bag Removing the Grass BagOperating Tips Cutting GrassCutting Leaves Maintenance Recommended Maintenance ScheduleCleaning the Underside of the Lawn Mower Housing Checking the Engine Oil LevelWashing Method Scraping MethodCleaning the Discharge Tunnel and Plug Servicing the Air FilterChanging the Engine Oil Maintaining the Cutting Blade Inspecting the BladeRemoving the Blade Emptying the Fuel Tank and Cleaning the Fuel Filter Cleaning under the Belt CoverInstalling the Blade Sharpening the BladeAdjusting the Self-propel Drive Lubricating the Pivot ArmsServicing the Spark Plug Changing the Oil FilterAdjusting the Blade Brake Cable Lubricating the Gear CaseHand-push Model only Storage Servicing the WheelsPreparing the Fuel System Removing the WheelsAccessories Preparing the EngineGeneral Information Removing the Lawn Mower from StorageTroubleshooting Problem Possible Causes Corrective ActionProblem Possible Causes Corrective Action Limited Warranty Exmark Turf Equipment Conditions and Products CoveredDescription Work Done Service Done By DateSee Exmarks Complete Line of Products for Turf Care