Exmark M216KA, M216KASP manual Operation, Controls, Starting the Engine, Stopping the Engine

Page 14

3.Fill the fuel tank with unleaded gasoline to within 1/4 to 1/2 inch (6 to 13 mm) from the top of the tank. Do not fill into the filler neck.

Important Do not fill the tank more than 1/4 inch

(6 mm) from the top of the tank because the gasoline must have room to expand.

4.Install the fuel tank cap and wipe up any spilled gasoline.

Operation

Note: Determine the left and right sides of the machine from the normal operating position.

Each time before you mow, make sure that the self-propel drive and the blade control bail operate properly. When you release the blade control bail, the blade and self-propel drive should stop. If they do not, contact an Authorized Service Dealer.

Caution

This machine produces sound levels in excess of 85dBA at the operator's ear and can cause hearing loss through extended periods of exposure.

Wear hearing protection when operating this machine.

Controls

The blade control bail, starter handle, and throttle control are on the upper handle as shown in Figure 9.

2

3

1

222

Figure 9

1. Blade control bail

3. Throttle control

2. Starter handle

Starting the Engine

1.Connect the wire to the spark plug (Fig. 10).

1

m-7280

Figure 10

1.Spark-plug wire

2.Open the fuel valve (Fig. 8).

3.Move the throttle control to the (Choke) position

(Fig. 9).

4.Move the ground speed control to the (Neutral) position (Fig. 11).

1

224

Figure 11

1. Ground speed control

5.Pull the starter handle (Fig. 8) lightly until you feel resistance, then pull it sharply.

6.Regulate the throttle and the ground speed control as desired when the engine starts.

Note: If the engine fails to start after 3 pulls, repeat steps 3 through 6.

Stopping the Engine

1.Release the blade control bail and move the throttle

control to the (Off) position.

2.Disconnect the wire from the spark plug if you do not use the lawn mower or if you leave it unattended.

10

Image 14
Contents M216KA / M216KASP Potential Hazard Exmark Parts PLUS Program Operators Manual Contents General Lawn Mower Safety SpecificationsSafety IntroductionPreparation OperationGeneral Operation Exmark Lawn Mower SafetyMaintenance and Storage Safety and Instruction Decals Assembly Installing the HandleInstalling the Discharge Tunnel Plug Installing the Starter RopeInstalling the Fuel Tank and the Fuel Line Oil Capacity Before StartingFilling the Crankcase with Oil Never buy more than a 30-day supply Filling the Fuel Tank with GasolineKeep it out of the reach of children GasolineStarting the Engine OperationControls Stopping the EngineOperating the Blade and the Self-Propel Drive Using the Discharge Tunnel PlugAdjusting the Cutting Height Mowing with the Grass Bag Using the Grass BagInstalling the Grass Bag Removing the Grass BagCutting Leaves Operating TipsCutting Grass Maintenance Recommended Maintenance ScheduleWashing Method Cleaning the Underside of the Lawn Mower HousingChecking the Engine Oil Level Scraping MethodChanging the Engine Oil Cleaning the Discharge Tunnel and PlugServicing the Air Filter Removing the Blade Maintaining the Cutting BladeInspecting the Blade Installing the Blade Emptying the Fuel Tank and Cleaning the Fuel FilterCleaning under the Belt Cover Sharpening the BladeAdjusting the Self-propel Drive Lubricating the Pivot ArmsServicing the Spark Plug Changing the Oil FilterHand-push Model only Adjusting the Blade Brake CableLubricating the Gear Case Preparing the Fuel System StorageServicing the Wheels Removing the WheelsGeneral Information AccessoriesPreparing the Engine Removing the Lawn Mower from StorageTroubleshooting Problem Possible Causes Corrective ActionProblem Possible Causes Corrective Action Limited Warranty Exmark Turf Equipment Conditions and Products CoveredDescription Work Done Service Done By DateSee Exmarks Complete Line of Products for Turf Care