Ferris Industries 5900751, 5900761 manual Troubleshooting the Mower, Rider Troubleshooting

Page 35

Troubleshooting, Adjustment & Service

RIDER TROUBLESHOOTING CONTINUED.

PROBLEM

CAUSE

REMEDY

Engine runs, but rider will

1.

Hydraulic release valve(s)

1. Turn valve(s) clockwise to close.

not drive.

 

in “open” position.

 

 

 

2.

Belt is broken.

2.

See Drive Belt Replacement.

 

3.

Drive belt slips.

3.

See problem and cause below.

 

4.

Brake is not fully released.

4.

See authorized service dealer

 

 

 

 

 

Rider drive belt slips.

1.

Pulleys or belt greasy or oily.

1.

Clean as required.

 

2.

Tension too loose.

2.

Adjust spring tension.

 

 

 

 

See Drive Belt Replacement

 

3.

Belt stretched or worn.

3.

Replace belt.

 

 

 

 

 

Brake will not hold.

1.

Brake is incorrectly adjusted.

1.

See Brake Adjustment.

 

2.

Brake pads worn.

2. Replace with new brake pads.

 

 

 

 

 

Rider steers or handles poorly.

1.

Steering linkage is loose.

1.

Check and tighten any loose connections.

 

2.

Improper tire inflation.

2.

See Regular Maintenance Section.

 

 

 

 

 

TROUBLESHOOTING THE MOWER

PROBLEM

CAUSE

REMEDY

Mower will not raise.

1.

Lift linkage not properly attached

1.

See authorized service dealer for repair.

 

 

or damaged.

 

 

 

 

 

 

 

Engine stalls easily with

1.

Engine speed too slow.

1.

Set to full throttle.

mower engaged.

2.

Ground speed too fast.

2. Decrease Ground Speed.

 

3.

Cutting height set too low.

3.

Cut tall grass at maximum cutting

 

 

 

 

height during first pass.

 

4.

Discharge chute jamming

4.

Cut grass with discharge pointing toward

 

 

with cut grass.

 

previously cut area.

 

 

 

 

Excessive mower vibration.

1.

Blade mounting bolts are loose.

1. Tighten to 70 ft.lbs. (94 N.m.).

 

2.

Mower blades, arbors,

2.

Check and replace as necessary.

 

 

or pulleys are bent.

 

 

 

3.

Mower blades are out

3. Remove, sharpen, and balance blades.

 

 

of balance.

 

See Maintenance Section.

 

4.

Belt installed incorrectly.

4.

Reinstall Correctly.

 

 

 

 

 

Excessive belt wear or breakage.

1.

Bent or rough pulleys.

1.

Repair or replace.

 

2.

Using incorrect belt.

2.

Replace with correct belt.

 

 

 

 

 

Mower drive belt slips

1.

Idler pulley spring broken or not

1.

Repair or replace as needed.

or fails to drive.

 

properly attached.

 

 

 

2.

Mower drive belt broken.

2.

Replace drive belt.

 

 

 

 

 

Mower does not engage.

1.

Electrical wiring damage.

1.

Locate & repair damaged wire.

 

2.

PTO clutch not adjusted

2. See PTO Clutch Adjustment section

 

3.

Battery voltage too low.

3.

Recharge battery and check alternator.

 

 

 

 

See Battery Maintenance section.

Troubleshooting

33

Page 34 Page 36
Image 35
Page 34 Page 36
Contents Model Number Briggs & Stratton Power Products Group, LLCDescription Date Purchased Table of Contents Operating Safety Slope Operation Roll Bar Use Fuel and Maintenance Preparation OperationTraining Emissions Slope OperationTowed Equipment RIDE-ON Units ChildrenIgnition System Gasoline Models Service and MaintenanceOperational Warnings Roll BAR InstructionsInspection and Maintenance of the Roll BAR Seat Belt Identification Identification NumbersSafety Decals Operational Safety Checks Safety Interlock SystemNorth American Safety Icons Ground Speed Control Levers Seat Adjustment LeverIgnition Switch Control FunctionsThrottle Control PTO Power Take Off SwitchHour Meter / Maintenance Reminder Parking BrakeChecks Before Starting General Operating SafetyPushing the Rider by Hand Starting the EngineStopping the Rider Reverse Travel Practice Zero Turn Driving PracticeSmooth Travel Forward Travel PracticeTurning Practice Turning Around a Corner Practice Turning In PlaceExecuting an End-Of-Row Zero Turn Executing TurnsTall Grass Requires Incremental Cutting MowingMowing Recommendations Height of GrassProper Broadcast Mowing When and How Often to MowMowing Methods Mowing PatternsProper Mulching Attaching a TrailerKeep roll bar in the raised position and use seat belt Raise & Lower the Roll BARTo lower the roll bar To raise the roll barLong Term Storage Longer Than 30 Days StorageStarting After Long Term Storage Temporary Storage 30 Days Or LessBefore Every Spring Each 100 250 Fall Use Hours Safety ItemsRider Maintenance Engine MaintenanceChange OIL & Filter Check Tire PressuresChecking / Adding Fuel Fuel FilterChange Interval Every 250 Hours Filter Part Number Check Hydraulic OIL LevelChange Hydraulic OIL Filter Lubricating the Front Casters LubricationGrease OilCleaning the Battery and Cables Air Cooled Models Battery MaintenanceInspecting the Mower Blades Servicing the Mower BladesRemoving the Mower Blade Balancing the Mower Blades Reinstalling the Mower BladesSharpening the Mower Blade Troubleshooting the Rider Troubleshooting WarningRider Troubleshooting Troubleshooting the MowerStreaking Troubleshooting Common Cutting ProblemsSpeed Balancing Adjustment Seat AdjustmentGround Speed Control Lever Adjustment RH side shown Neutral AdjustmentRETURN-TO-NEUTRAL Adjustment Adjustment Linkage RodParking Brake Adjustment Brake Spring Adjustment Nut Parking Brake AdjustmentTo adjust the upper mounting position Rear Suspension AdjustmentTo adjust the spring pre-load To adjust pedal position Mowing Height AdjustmentFoot Pedal Adjustment Check Lift Rod Timing Deck Lift ROD Timing AdjustmentDeck Lift Spring Deck Leveling AdjustmentHydraulic Pump Drive Belt Replacement Mower PTO Belt Idler Arm Stationary Idler Pulley Mower Belt ReplacementJump Starting With Auxiliary Booster Battery Battery ServiceChecking Battery Voltage Charging a Completely Discharged BatteryJump Starting This HOOK-UP for Negative Ground VehiclesMake Certain Vehicles do not Touch Transmissions DimensionsEngine ChassisFerris Limited Warranty Mower Deck Belts and BladesTractor

5900761, 5900751 specifications

Ferris Industries has long been recognized for its innovative approach to outdoor power equipment, and the models 5900751 and 5900761 exemplify this commitment to quality and performance. With features tailored for both residential and commercial use, these products showcase advanced technologies that enhance user experience and operational efficiency.

The Ferris Industries 5900751 model stands out with its robust build and powerful engine, designed to tackle a variety of mowing tasks effortlessly. This model is equipped with a reliable commercial-grade engine that provides ample power to tackle even the most challenging terrains. The cutting deck, optimized for superior grass clipping management, ensures a clean and even cut, making it ideal for maintaining professional-looking lawns.

Similarly, the 5900761 brings its own unique set of features that make it a formidable choice for larger properties or commercial settings. One of its standout characteristics is the durable construction that helps resist wear and tear over time. With a larger cutting deck and an efficient powertrain, this model is designed to cover more ground in less time, boosting productivity significantly.

Both models incorporate Ferris's patented suspension technology. The advanced suspension system reduces operator fatigue, allowing for longer mowing sessions with greater comfort. This technology also improves traction and stability on uneven surfaces, ensuring a smoother ride regardless of the landscape.

In terms of technology, both the 5900751 and 5900761 feature user-friendly controls that enhance maneuverability. The intuitive dashboard displays vital information, providing operators with insights into performance metrics at a glance. Additionally, the ease of maintenance is a focal point, with accessible components that streamline service tasks, ensuring that downtime is minimized.

The ergonomic design of the handles and seat enhances user comfort and control, allowing for effortless navigation around obstacles. Safety features such as a reliable braking system and roll-over protection further ensure that operators can work with confidence.

In summary, Ferris Industries models 5900751 and 5900761 are powerful and efficient solutions for anyone looking to invest in reliable outdoor power equipment. With their durable design, advanced suspension technology, and user-focused features, these models continue to set the standard for excellence in the industry. Whether for personal use or professional landscaping, Ferris delivers equipment that meets the demands of any task with exceptional performance.
Top Page Image Contents