Ferris Industries 5900761, 5900751 manual Hydraulic Pump Drive Belt Replacement

Page 44

Troubleshooting, Adjustment & Service

HYDRAULIC PUMP DRIVE BELT REPLACEMENT

1.Park the tractor on a smooth, level surface such as a concrete floor. Disengage the PTO, engage the parking brake, turn off the engine, and remove the ignition key.

2.Remove the PTO drive belt (see MOWER BELT REPLACEMENT for removal instructions).

3.Remove the hardware that secures the clutch anchor pad to the PTO clutch.

4.Loosen the nut towards the front of the machine on the spring anchor hook (G, Figure 46) to release the majority of the belt tension. Use caution and remove the nut to completely release the tension.

5.Remove the old belt and replace it with a new one. Make sure the V-side of the belt runs in the grooves of the crankshaft pulley and pump pulleys (B & C).

6.Reinstall the anchor hook (G) into the anchor tab and loosely fasten the nut. Adjust the anchor hook until a measurement of 8-3/8” (21,2 cm) is achieved from the outside if the spring hooks. Tighten nut.

7.Reinstall the clutch anchor pad to the PTO clutch and secure with the hardware previously removed.

8.Reinstall the PTO drive belt.

 

B

 

 

D

A

8 3/8

E

 

(21,2 cm)

 

 

C

 

C

 

 

 

F

G

Figure 46. Hydraulic Pump Drive Belt

Replacement

A.Pump Drive Belt

B.Crankshaft Pulley

C.Pump Pulley

D.Idler Pulley

E.Idler Arm

F.Spring

G.Spring Anchor Hook

Troubleshooting

42

www.ferrisindustries.com

Image 44
Contents Model Number Briggs & Stratton Power Products Group, LLCDescription Date Purchased Table of Contents Operating Safety Slope Operation Roll Bar Use Fuel and Maintenance Preparation OperationTraining Slope Operation Towed Equipment RIDE-ON UnitsChildren EmissionsService and Maintenance Ignition System Gasoline ModelsRoll BAR Instructions Operational WarningsInspection and Maintenance of the Roll BAR Seat Belt Identification Numbers IdentificationSafety Decals Operational Safety Checks Safety Interlock SystemNorth American Safety Icons Seat Adjustment Lever Ignition SwitchControl Functions Ground Speed Control LeversPTO Power Take Off Switch Hour Meter / Maintenance ReminderParking Brake Throttle ControlGeneral Operating Safety Checks Before StartingPushing the Rider by Hand Starting the EngineStopping the Rider Zero Turn Driving Practice Smooth TravelForward Travel Practice Reverse Travel PracticePractice Turning Around a Corner Practice Turning In Place Executing an End-Of-Row Zero TurnExecuting Turns TurningMowing Mowing RecommendationsHeight of Grass Tall Grass Requires Incremental CuttingWhen and How Often to Mow Mowing MethodsMowing Patterns Proper Broadcast MowingAttaching a Trailer Proper MulchingRaise & Lower the Roll BAR To lower the roll barTo raise the roll bar Keep roll bar in the raised position and use seat beltStorage Starting After Long Term StorageTemporary Storage 30 Days Or Less Long Term Storage Longer Than 30 DaysSafety Items Rider MaintenanceEngine Maintenance Before Every Spring Each 100 250 Fall Use HoursCheck Tire Pressures Checking / Adding FuelFuel Filter Change OIL & FilterChange Interval Every 250 Hours Filter Part Number Check Hydraulic OIL LevelChange Hydraulic OIL Filter Lubrication GreaseOil Lubricating the Front CastersBattery Maintenance Cleaning the Battery and Cables Air Cooled ModelsInspecting the Mower Blades Servicing the Mower BladesRemoving the Mower Blade Balancing the Mower Blades Reinstalling the Mower BladesSharpening the Mower Blade Troubleshooting Warning Troubleshooting the RiderTroubleshooting the Mower Rider TroubleshootingTroubleshooting Common Cutting Problems StreakingSpeed Balancing Adjustment Seat AdjustmentGround Speed Control Lever Adjustment Neutral Adjustment RETURN-TO-NEUTRAL AdjustmentAdjustment Linkage Rod RH side shownParking Brake Adjustment Parking Brake Adjustment Brake Spring Adjustment NutTo adjust the upper mounting position Rear Suspension AdjustmentTo adjust the spring pre-load To adjust pedal position Mowing Height AdjustmentFoot Pedal Adjustment Deck Lift ROD Timing Adjustment Check Lift Rod TimingDeck Leveling Adjustment Deck Lift SpringHydraulic Pump Drive Belt Replacement Mower Belt Replacement Mower PTO Belt Idler Arm Stationary Idler PulleyBattery Service Checking Battery VoltageCharging a Completely Discharged Battery Jump Starting With Auxiliary Booster BatteryJump Starting This HOOK-UP for Negative Ground VehiclesMake Certain Vehicles do not Touch Dimensions EngineChassis TransmissionsFerris Limited Warranty Mower Deck Belts and BladesTractor

5900761, 5900751 specifications

Ferris Industries has long been recognized for its innovative approach to outdoor power equipment, and the models 5900751 and 5900761 exemplify this commitment to quality and performance. With features tailored for both residential and commercial use, these products showcase advanced technologies that enhance user experience and operational efficiency.

The Ferris Industries 5900751 model stands out with its robust build and powerful engine, designed to tackle a variety of mowing tasks effortlessly. This model is equipped with a reliable commercial-grade engine that provides ample power to tackle even the most challenging terrains. The cutting deck, optimized for superior grass clipping management, ensures a clean and even cut, making it ideal for maintaining professional-looking lawns.

Similarly, the 5900761 brings its own unique set of features that make it a formidable choice for larger properties or commercial settings. One of its standout characteristics is the durable construction that helps resist wear and tear over time. With a larger cutting deck and an efficient powertrain, this model is designed to cover more ground in less time, boosting productivity significantly.

Both models incorporate Ferris's patented suspension technology. The advanced suspension system reduces operator fatigue, allowing for longer mowing sessions with greater comfort. This technology also improves traction and stability on uneven surfaces, ensuring a smoother ride regardless of the landscape.

In terms of technology, both the 5900751 and 5900761 feature user-friendly controls that enhance maneuverability. The intuitive dashboard displays vital information, providing operators with insights into performance metrics at a glance. Additionally, the ease of maintenance is a focal point, with accessible components that streamline service tasks, ensuring that downtime is minimized.

The ergonomic design of the handles and seat enhances user comfort and control, allowing for effortless navigation around obstacles. Safety features such as a reliable braking system and roll-over protection further ensure that operators can work with confidence.

In summary, Ferris Industries models 5900751 and 5900761 are powerful and efficient solutions for anyone looking to invest in reliable outdoor power equipment. With their durable design, advanced suspension technology, and user-focused features, these models continue to set the standard for excellence in the industry. Whether for personal use or professional landscaping, Ferris delivers equipment that meets the demands of any task with exceptional performance.