Ferris Industries 5900751, 5900761 manual Mowing Height Adjustment, Foot Pedal Adjustment

Page 41

Troubleshooting, Adjustment & Service

MOWING HEIGHT ADJUSTMENT

The cutting height adjustment pin (A, Figure 37) controls the mower cutting height. The cutting height is adjustable between 1-3/4” (4,4 cm) and 5” (12,7 cm) in 1/4” (0,64 cm) increments.

1.Depress the deck lift foot pedal (B) until it locks into the 5” (12,7 cm) position.

2.Place the cutting height adjustment pin in the desired cutting height.

3.Depress the deck lift foot pedal then push the lock lever (C) towards the right to release the lock.

4.Release the deck lift foot pedal until it comes to rest against the cutting height adjustment pin.

 

C

B

A

 

FOOT PEDAL ADJUSTMENT

The deck lift foot pedal can be adjusted to accommodate the operator’s height for optimal comfort.

To adjust pedal position:

1.Remove the foot pedal (A, Figure 38) from the pedal mount tab (B).

2.Remove the pedal mount hardware (C) and rotate the tab 180 degrees.

3.Reinstall the pedal mount hardware and tighten securely.

4.Reinstall the foot pedal on the pedal mount tab in the proper orientation as shown in Figure 38.

Figure 37. Mowing Height Adjustment

A.Cutting Height Adjustment Pin

B.Deck Lift Foot Pedal

C.Deck Lift Lock lever

B

AC

Figure 38. Foot Pedal Adjustment

A.Deck Lift Foot Pedal

B.Pedal Mount Tab

C.Pedal Mount Hardware

Troubleshooting

39

Page 40 Page 42
Image 41
Page 40 Page 42
Contents Model Number Briggs & Stratton Power Products Group, LLCDescription Date Purchased Table of Contents Operating Safety Slope Operation Roll Bar Use Fuel and Maintenance Preparation OperationTraining Towed Equipment RIDE-ON Units Slope OperationChildren EmissionsIgnition System Gasoline Models Service and MaintenanceOperational Warnings Roll BAR InstructionsInspection and Maintenance of the Roll BAR Seat Belt Identification Identification NumbersSafety Decals Operational Safety Checks Safety Interlock SystemNorth American Safety Icons Ignition Switch Seat Adjustment LeverControl Functions Ground Speed Control LeversHour Meter / Maintenance Reminder PTO Power Take Off SwitchParking Brake Throttle ControlChecks Before Starting General Operating SafetyPushing the Rider by Hand Starting the EngineStopping the Rider Smooth Travel Zero Turn Driving PracticeForward Travel Practice Reverse Travel PracticeExecuting an End-Of-Row Zero Turn Practice Turning Around a Corner Practice Turning In PlaceExecuting Turns TurningMowing Recommendations MowingHeight of Grass Tall Grass Requires Incremental CuttingMowing Methods When and How Often to MowMowing Patterns Proper Broadcast MowingProper Mulching Attaching a TrailerTo lower the roll bar Raise & Lower the Roll BARTo raise the roll bar Keep roll bar in the raised position and use seat beltStarting After Long Term Storage StorageTemporary Storage 30 Days Or Less Long Term Storage Longer Than 30 DaysRider Maintenance Safety ItemsEngine Maintenance Before Every Spring Each 100 250 Fall Use HoursChecking / Adding Fuel Check Tire PressuresFuel Filter Change OIL & FilterChange Interval Every 250 Hours Filter Part Number Check Hydraulic OIL LevelChange Hydraulic OIL Filter Grease LubricationOil Lubricating the Front CastersCleaning the Battery and Cables Air Cooled Models Battery MaintenanceInspecting the Mower Blades Servicing the Mower BladesRemoving the Mower Blade Balancing the Mower Blades Reinstalling the Mower BladesSharpening the Mower Blade Troubleshooting the Rider Troubleshooting WarningRider Troubleshooting Troubleshooting the MowerStreaking Troubleshooting Common Cutting ProblemsSpeed Balancing Adjustment Seat AdjustmentGround Speed Control Lever Adjustment RETURN-TO-NEUTRAL Adjustment Neutral AdjustmentAdjustment Linkage Rod RH side shownParking Brake Adjustment Brake Spring Adjustment Nut Parking Brake AdjustmentTo adjust the upper mounting position Rear Suspension AdjustmentTo adjust the spring pre-load To adjust pedal position Mowing Height AdjustmentFoot Pedal Adjustment Check Lift Rod Timing Deck Lift ROD Timing AdjustmentDeck Lift Spring Deck Leveling AdjustmentHydraulic Pump Drive Belt Replacement Mower PTO Belt Idler Arm Stationary Idler Pulley Mower Belt ReplacementChecking Battery Voltage Battery ServiceCharging a Completely Discharged Battery Jump Starting With Auxiliary Booster BatteryJump Starting This HOOK-UP for Negative Ground VehiclesMake Certain Vehicles do not Touch Engine DimensionsChassis TransmissionsFerris Limited Warranty Mower Deck Belts and BladesTractor

5900761, 5900751 specifications

Ferris Industries has long been recognized for its innovative approach to outdoor power equipment, and the models 5900751 and 5900761 exemplify this commitment to quality and performance. With features tailored for both residential and commercial use, these products showcase advanced technologies that enhance user experience and operational efficiency.

The Ferris Industries 5900751 model stands out with its robust build and powerful engine, designed to tackle a variety of mowing tasks effortlessly. This model is equipped with a reliable commercial-grade engine that provides ample power to tackle even the most challenging terrains. The cutting deck, optimized for superior grass clipping management, ensures a clean and even cut, making it ideal for maintaining professional-looking lawns.

Similarly, the 5900761 brings its own unique set of features that make it a formidable choice for larger properties or commercial settings. One of its standout characteristics is the durable construction that helps resist wear and tear over time. With a larger cutting deck and an efficient powertrain, this model is designed to cover more ground in less time, boosting productivity significantly.

Both models incorporate Ferris's patented suspension technology. The advanced suspension system reduces operator fatigue, allowing for longer mowing sessions with greater comfort. This technology also improves traction and stability on uneven surfaces, ensuring a smoother ride regardless of the landscape.

In terms of technology, both the 5900751 and 5900761 feature user-friendly controls that enhance maneuverability. The intuitive dashboard displays vital information, providing operators with insights into performance metrics at a glance. Additionally, the ease of maintenance is a focal point, with accessible components that streamline service tasks, ensuring that downtime is minimized.

The ergonomic design of the handles and seat enhances user comfort and control, allowing for effortless navigation around obstacles. Safety features such as a reliable braking system and roll-over protection further ensure that operators can work with confidence.

In summary, Ferris Industries models 5900751 and 5900761 are powerful and efficient solutions for anyone looking to invest in reliable outdoor power equipment. With their durable design, advanced suspension technology, and user-focused features, these models continue to set the standard for excellence in the industry. Whether for personal use or professional landscaping, Ferris delivers equipment that meets the demands of any task with exceptional performance.
Top Page Image Contents