Ferris Industries 5900761, 5900751 manual Deck Lift ROD Timing Adjustment, Check Lift Rod Timing

Page 42

Troubleshooting, Adjustment & Service

DECK LIFT ROD TIMING

ADJUSTMENT

1. Park machine on a flat, level surface. Disengage the PTO, stop the engine and engage the parking brake. Rear tires must be inflated to 15 psi (1,03

bar); front tires to 25 psi (1,72 bar).

Troubleshooting

2.To check the deck lift rod timing, measure and record the distance between the lift pivots and the rod pivots. Repeat for other side of unit. See Figure 39.

3.If the measurements are equal, skip to Step 5. If the measurements are NOT equal (greater than 1/8” (3,17mm) difference), adjustment is required, continue with Step 4.

4.Lock the deck lift pedal in the 5” (12,7 cm) position. Remove the cutting height adjustment pin and lower the mower deck.

5.To ensure that the deck is in the lowest position, push the pedal by hand towards the rear of the unit and install the height adjustment pin in the 3” (7.6cm) position to hold in place. See Figure 40.

6.Block up the mower deck until all hanger chains are slack. See Figure 41.

7.Refer to Figure 42. To adjust the inner lift rod, loosen the jam nut on the front ball joint then remove the 1/2” hardware fastening the ball joint the the lift pivot arm. Turn the ball joint clockwise to shorten the distance between the rod pivots or counterclockwise to lengthen the distance between the rod pivots. Reinstall the ball joint on the lift pivot arm and secure with the 1/2” hardware previously removed. Tighten the jam nut against the lift rod.

8.Remove blocks from under the mower deck.

9.Remove the the cutting height adjustment pin from in front of the deck lift pedal arm. Lift mower deck and reinstall adjustment pin in desired mowing height.

Figure 39. Check Lift Rod Timing

Figure 40. Deck Lift Pedal & Pin Position

Figure 41.

2 x 4 Locations

Figure 42. Adjust Lift Rod Timing

40

www.ferrisindustries.com

Image 42
Contents Briggs & Stratton Power Products Group, LLC DescriptionModel Number Date Purchased Table of Contents Operating Safety Slope Operation Roll Bar Use Fuel and Maintenance Operation TrainingPreparation Children Slope OperationTowed Equipment RIDE-ON Units EmissionsService and Maintenance Ignition System Gasoline ModelsRoll BAR Instructions Operational WarningsInspection and Maintenance of the Roll BAR Seat Belt Identification Numbers IdentificationSafety Decals Safety Interlock System North American Safety IconsOperational Safety Checks Control Functions Seat Adjustment LeverIgnition Switch Ground Speed Control LeversParking Brake PTO Power Take Off SwitchHour Meter / Maintenance Reminder Throttle ControlGeneral Operating Safety Checks Before StartingStarting the Engine Stopping the RiderPushing the Rider by Hand Forward Travel Practice Zero Turn Driving PracticeSmooth Travel Reverse Travel PracticeExecuting Turns Practice Turning Around a Corner Practice Turning In PlaceExecuting an End-Of-Row Zero Turn TurningHeight of Grass MowingMowing Recommendations Tall Grass Requires Incremental CuttingMowing Patterns When and How Often to MowMowing Methods Proper Broadcast MowingAttaching a Trailer Proper MulchingTo raise the roll bar Raise & Lower the Roll BARTo lower the roll bar Keep roll bar in the raised position and use seat beltTemporary Storage 30 Days Or Less StorageStarting After Long Term Storage Long Term Storage Longer Than 30 DaysEngine Maintenance Safety ItemsRider Maintenance Before Every Spring Each 100 250 Fall Use HoursFuel Filter Check Tire PressuresChecking / Adding Fuel Change OIL & FilterCheck Hydraulic OIL Level Change Hydraulic OIL FilterChange Interval Every 250 Hours Filter Part Number Oil LubricationGrease Lubricating the Front CastersBattery Maintenance Cleaning the Battery and Cables Air Cooled ModelsServicing the Mower Blades Removing the Mower BladeInspecting the Mower Blades Reinstalling the Mower Blades Sharpening the Mower BladeBalancing the Mower Blades Troubleshooting Warning Troubleshooting the RiderTroubleshooting the Mower Rider TroubleshootingTroubleshooting Common Cutting Problems StreakingSeat Adjustment Ground Speed Control Lever AdjustmentSpeed Balancing Adjustment Adjustment Linkage Rod Neutral AdjustmentRETURN-TO-NEUTRAL Adjustment RH side shownParking Brake Adjustment Parking Brake Adjustment Brake Spring Adjustment NutRear Suspension Adjustment To adjust the spring pre-loadTo adjust the upper mounting position Mowing Height Adjustment Foot Pedal AdjustmentTo adjust pedal position Deck Lift ROD Timing Adjustment Check Lift Rod TimingDeck Leveling Adjustment Deck Lift SpringHydraulic Pump Drive Belt Replacement Mower Belt Replacement Mower PTO Belt Idler Arm Stationary Idler PulleyCharging a Completely Discharged Battery Battery ServiceChecking Battery Voltage Jump Starting With Auxiliary Booster BatteryThis HOOK-UP for Negative Ground Vehicles Make Certain Vehicles do not TouchJump Starting Chassis DimensionsEngine TransmissionsFerris Limited Warranty Belts and Blades TractorMower Deck

5900761, 5900751 specifications

Ferris Industries has long been recognized for its innovative approach to outdoor power equipment, and the models 5900751 and 5900761 exemplify this commitment to quality and performance. With features tailored for both residential and commercial use, these products showcase advanced technologies that enhance user experience and operational efficiency.

The Ferris Industries 5900751 model stands out with its robust build and powerful engine, designed to tackle a variety of mowing tasks effortlessly. This model is equipped with a reliable commercial-grade engine that provides ample power to tackle even the most challenging terrains. The cutting deck, optimized for superior grass clipping management, ensures a clean and even cut, making it ideal for maintaining professional-looking lawns.

Similarly, the 5900761 brings its own unique set of features that make it a formidable choice for larger properties or commercial settings. One of its standout characteristics is the durable construction that helps resist wear and tear over time. With a larger cutting deck and an efficient powertrain, this model is designed to cover more ground in less time, boosting productivity significantly.

Both models incorporate Ferris's patented suspension technology. The advanced suspension system reduces operator fatigue, allowing for longer mowing sessions with greater comfort. This technology also improves traction and stability on uneven surfaces, ensuring a smoother ride regardless of the landscape.

In terms of technology, both the 5900751 and 5900761 feature user-friendly controls that enhance maneuverability. The intuitive dashboard displays vital information, providing operators with insights into performance metrics at a glance. Additionally, the ease of maintenance is a focal point, with accessible components that streamline service tasks, ensuring that downtime is minimized.

The ergonomic design of the handles and seat enhances user comfort and control, allowing for effortless navigation around obstacles. Safety features such as a reliable braking system and roll-over protection further ensure that operators can work with confidence.

In summary, Ferris Industries models 5900751 and 5900761 are powerful and efficient solutions for anyone looking to invest in reliable outdoor power equipment. With their durable design, advanced suspension technology, and user-focused features, these models continue to set the standard for excellence in the industry. Whether for personal use or professional landscaping, Ferris delivers equipment that meets the demands of any task with exceptional performance.