Husqvarna 13 manual Maintenance schedule, Daily Maintenance interval Hours Nance 100

Page 23

MAINTENANCE

Maintenance schedule

The following is a list of the maintenance which should be conducted on the machine. For the items which are not described in these instructions go to an authorised service workshop.

 

 

Daily

Maintenance interval

Maintenance

Page

mainte-

 

in hours

 

nance

25

50

100

 

 

before start

 

 

 

 

 

 

Check the engine’s oil level

37

●

 

 

 

Check the engine’s cooling air inlet

30

●

 

 

 

Check the fuel pump’s air filter

28

●

 

 

 

Check the steering wires

24

●

 

 

 

Check the brakes

25

●

 

 

 

Check the battery

28

●

 

 

 

Check the safety system

29

●

 

 

 

Check screws and nuts

–

❍

 

 

 

Check for fuel and oil leakage

–

❍

 

 

 

Change the engine oil 1)

37

 

●

 

 

Clean the air filter’s pre-filter (foam plastic) 2)

27

 

●

 

 

Check the cutting unit

31

 

●

 

 

Check the tyre pressures (60 kPa)

30

 

●

 

 

Lubricating the belt adjuster 3)

38

 

●

 

 

Lubricate joints and shafts 3)

39

 

●

 

 

Adjust the brakes – Rider 11 and Rider 11 Bio

25

 

●

 

 

Check the V-belts

–

 

❍

 

 

Check the transmission’s cooling flanges –

–

 

❍

 

 

Rider 13 and Rider 13 Bio

 

 

 

 

 

Check the transmission’s oil level – Rider 13 and

39

 

 

●

 

Rider 13 Bio

 

 

 

 

 

Adjust the brakes – Rider 13 and Rider 13 Bio

25

 

 

●

 

Check and adjust the throttle wire

26

 

 

●

 

Clean the cooling flanges on the engine and

–

 

 

❍

 

transmission 2,4)

 

 

 

 

 

Replace the air filter’s pre-filter and paper filter 2)

27

 

 

 

●

Replace the fuel filter

26

 

 

 

●

Replace the plug

28

 

 

 

●

 

 

 

 

 

 

1)First change after 5 hours. 2) During dusty conditions cleaning and replacement should be more frequent. 3) For daily use of the machine lubrication should be conducted twice a week. 4) Conducted by authorised service workshop.

● = Described in these instructions.

❍= Not described in these instructions.

WARNING!

No service procedures must be conducted on the engine or cutting unit unless:

•

The engine is switched off.

• The parking brake is applied.

 

 

•

The ignition key is removed.

• The cutting unit is disengaged.

 

 

•The ignition cable is removed from the plug.

English – 21

Page 22 Page 24
Image 23
Page 22 Page 24
Contents Rider 11 Rider 13 Rider 11 Bio Rider 13 Bio Svenska Contents Towing IntroduktionDear customer Travel and transport on public roadsSerial number Safety InstructionsGood service Slope Explanation of SymbolsGeneral use Safety instructionsKeep children away from the area to be mowed Proceed as follows Driving on slopesChildren MaintenanceDo not smoke when carrying out maintenance Transport Location of the controls PresentationPresentation Brake pedal / Parking brake Presentation Rider 11 / 11 BIOThrottle and Choke lever Clutch pedalParking brake Presentation Rider 13/13 BIOSpeed limiter Lift lever for cutting unit Cutting unitFuelling Lever for adjustment of cutting heightSee safety instructions SeatFor Rider 11 and Rider 11 Bio Set the gear DrivingBefore starting Starting the engineWarm engine Cold engineFor Rider 11 and Rider 11 Bio Driving the machineFor Rider 13 and Rider 13 Bio Cutting tips Release lever Rider 13 and Rider 13 Bio Hill start, manual gearboxStopping the engine Daily Maintenance interval Hours Nance 100 MaintenanceMaintenance schedule Front hood Rider 11 and Rider Dismantling of the machine hoodsEngine hood Left-hand fender Right-hand fenderChecking and adjustment of the steering wires Checking the brake Rider 11 Rider 11 Bio Adjusting the brake Rider 11 and Rider 11 BioCheck and adjust the brakes on Rider 13 and Rider 13 Bio Poorly adjusted brakes can result in reduced braking powerReplacement of the fuel filter Checking and adjustment of the throttle wireReplacing the air filter Do not use compressed air to clean the paper filterFitting the wrong spark plug type can damage the engine Check the level of the battery acidProcedures on contact with acid Checking of the fuel pump’s air filterInspecting the safety system Check the engine’s cooling air intake Checking the tyre pressureChecking the cutting unit’s parallelism 6008-026H Placing in service position Maintenance Rider 11 BIO/13 BIOService position for BioClip 6017-221 6017-222 Take care not to get your hand trapped Restoring from service positionReplacing the break-pin BioClip Checking the bladesChanging the oil LubricationCheck the engine’s oil level General lubrication Lubrication of belt tensionerLubrication of front wheel bearings Lubrication Rider 11 and Rider 11 BioProblem Procedure Trouble Shooting ScheduleWinter storage ServiceStorage Technical Data Electrical system Rider 13 Bio Dimensions Rider 11 BioEU declaration of conformity Only applies to Europe EU-DECLARATION of ConformityWork done Servicejournal Rider 11/13Pre-delivery service After first 5 hoursWork done Date, mileage, stamp, sign ServicejournalServicejournal ´+H$r¶6C¨ Page 114 00

13, 11, 13, 11 Bio, 13 Bio specifications

Husqvarna is a brand synonymous with quality and innovation in the realm of outdoor power equipment, and the 11 and 13 series are prime examples of their commitment to excellence. The 11 and 13 models, including the 11 Bio and 13 Bio versions, showcase the brand's focus on performance, efficiency, and environmentally friendly practices. Both series are designed to cater to the needs of professionals and homeowners alike, making them versatile options for various landscaping and maintenance tasks.

The Husqvarna 11 series is characterized by its lightweight design and ease of use. These models include powerful engines that provide exceptional cutting performance, ensuring that tasks such as trimming, mowing, and edging are completed efficiently. One of the standout features of the 11 series is its ergonomic design, which reduces operator fatigue and enhances comfort during extended use. The intuitive controls make adjustments straightforward, helping users to focus on their work rather than struggling with complicated machinery.

On the other hand, the Husqvarna 13 series builds upon the strengths of the 11 series with increased power and advanced technology. The 13 models come equipped with a more potent engine, allowing for deeper, more efficient cutting. These units also feature improved fuel efficiency, which translates to lower running costs and fewer emissions. The Bio variants of both series, specifically the 11 Bio and 13 Bio, emphasize sustainability without sacrificing performance. These models incorporate specialized cutting systems designed to reduce waste and promote better mulching capabilities, making them ideal for environmentally conscious users.

Both series include advanced filtration systems that ensure longer engine life and reduced maintenance intervals. Integrated safety features are also paramount, with automatic shutdown functions and improved visibility for the operator. Furthermore, the durability of Husqvarna’s construction means these machines can withstand the rigors of daily use, making them a worthwhile investment for any user.

In conclusion, the Husqvarna 11 and 13 series, including the Bio variants, stand out in the market for their thoughtful design and innovative technology. These models demonstrate Husqvarna's dedication to creating efficient, powerful, and environmentally friendly equipment that meets the diverse needs of users everywhere. Whether you are a professional landscaper or a dedicated homeowner, the Husqvarna 11 and 13 series deliver performance, reliability, and sustainability.
Top Page Image Contents