Husqvarna 11, 13, 11 Bio, 13 Bio Lubrication, Check the engine’s oil level, Changing the oil

Page 39

LUBRICATION

Check the engine’s oil level

Check the oil level in the engine when the machine is horizontal.

Raise the engine cover.

Release the dip stick and pull out. Wipe off the oil and insert again.

The dip stick must be fully screwed down.

Now release the dip stick again and pull out. Check the oil level.

The oil level should lie between the markings on dip stick. If the level approaches the ”ADD” mark, top up with oil to the ”FULL” mark.

The oil is filled in the same hole for the dip stick

Use engine oil SAE 30 or SAE 10W/30, class SF-CC.

The total oil volume in the engine is 1.4 litres.

Changing the oil

The oil should be changed for the first time after 5 hours of running time. Thereafter it should be changed every 25 hours of running time.

WARNING!

Engine oil can be very hot if it is drained off directly after the engine is stopped. Therefore allow the engine to cool down first.

1.Place a receptacle under the engine’s drain plug, located on the left-hand side of the engine.

2.Remove the dip stick and drain plug.

3.Let the oil run out into the receptacle.

4.Fit the drain plug and tighten.

5.Fill up with oil to the ”FULL” mark on the dip stick. The oil is filled in the same hole for the dip stick.

Use engine oil SAE 30 or SAE 10W/30, class SF-CC.

Use engine oil with min. API SF quality and SAE 30 or SAE 10W/30 viscosity grade. The oil volume in the engine is 1.4 litres.

6.Run the engine warm and then check that there is no leakage from the drain plug.

6008-005

 

ADD

FULL

ADD

FULL

 

 

 

6008-035

6008-027

IMPORTANT INFORMATION

Used engine oil is hazardous to health and environment and must in accordance with the law not be poured out on the ground or in the nature, and must be handed in to a workshop or other designated station for treatment. Avoid skin contact, wash with soap and water in the event of spillage.

English – 37

Page 38 Page 40
Image 39
Page 38 Page 40
Contents Rider 11 Rider 13 Rider 11 Bio Rider 13 Bio Svenska Contents Towing IntroduktionDear customer Travel and transport on public roadsSafety Instructions Good serviceSerial number Slope Explanation of SymbolsGeneral use Safety instructionsKeep children away from the area to be mowed Proceed as follows Driving on slopesChildren MaintenanceDo not smoke when carrying out maintenance Transport Presentation PresentationLocation of the controls Brake pedal / Parking brake Presentation Rider 11 / 11 BIOThrottle and Choke lever Clutch pedalPresentation Rider 13/13 BIO Speed limiterParking brake Lift lever for cutting unit Cutting unitFuelling Lever for adjustment of cutting heightSee safety instructions SeatFor Rider 11 and Rider 11 Bio Set the gear DrivingBefore starting Starting the engineWarm engine Cold engineDriving the machine For Rider 13 and Rider 13 BioFor Rider 11 and Rider 11 Bio Cutting tips Hill start, manual gearbox Stopping the engineRelease lever Rider 13 and Rider 13 Bio Maintenance Maintenance scheduleDaily Maintenance interval Hours Nance 100 Dismantling of the machine hoods Engine hoodFront hood Rider 11 and Rider Left-hand fender Right-hand fenderChecking and adjustment of the steering wires Checking the brake Rider 11 Rider 11 Bio Adjusting the brake Rider 11 and Rider 11 BioCheck and adjust the brakes on Rider 13 and Rider 13 Bio Poorly adjusted brakes can result in reduced braking powerReplacement of the fuel filter Checking and adjustment of the throttle wireReplacing the air filter Do not use compressed air to clean the paper filterFitting the wrong spark plug type can damage the engine Check the level of the battery acidProcedures on contact with acid Checking of the fuel pump’s air filterInspecting the safety system Check the engine’s cooling air intake Checking the tyre pressureChecking the cutting unit’s parallelism 6008-026H Maintenance Rider 11 BIO/13 BIO Service position for BioClipPlacing in service position 6017-221 6017-222 Take care not to get your hand trapped Restoring from service positionReplacing the break-pin BioClip Checking the bladesLubrication Check the engine’s oil levelChanging the oil General lubrication Lubrication of belt tensionerLubrication of front wheel bearings Lubrication Rider 11 and Rider 11 BioProblem Procedure Trouble Shooting ScheduleService StorageWinter storage Technical Data Electrical system Rider 13 Bio Dimensions Rider 11 BioEU declaration of conformity Only applies to Europe EU-DECLARATION of ConformityWork done Servicejournal Rider 11/13Pre-delivery service After first 5 hoursWork done Date, mileage, stamp, sign ServicejournalServicejournal ´+H$r¶6C¨ Page 114 00

13, 11, 13, 11 Bio, 13 Bio specifications

Husqvarna is a brand synonymous with quality and innovation in the realm of outdoor power equipment, and the 11 and 13 series are prime examples of their commitment to excellence. The 11 and 13 models, including the 11 Bio and 13 Bio versions, showcase the brand's focus on performance, efficiency, and environmentally friendly practices. Both series are designed to cater to the needs of professionals and homeowners alike, making them versatile options for various landscaping and maintenance tasks.

The Husqvarna 11 series is characterized by its lightweight design and ease of use. These models include powerful engines that provide exceptional cutting performance, ensuring that tasks such as trimming, mowing, and edging are completed efficiently. One of the standout features of the 11 series is its ergonomic design, which reduces operator fatigue and enhances comfort during extended use. The intuitive controls make adjustments straightforward, helping users to focus on their work rather than struggling with complicated machinery.

On the other hand, the Husqvarna 13 series builds upon the strengths of the 11 series with increased power and advanced technology. The 13 models come equipped with a more potent engine, allowing for deeper, more efficient cutting. These units also feature improved fuel efficiency, which translates to lower running costs and fewer emissions. The Bio variants of both series, specifically the 11 Bio and 13 Bio, emphasize sustainability without sacrificing performance. These models incorporate specialized cutting systems designed to reduce waste and promote better mulching capabilities, making them ideal for environmentally conscious users.

Both series include advanced filtration systems that ensure longer engine life and reduced maintenance intervals. Integrated safety features are also paramount, with automatic shutdown functions and improved visibility for the operator. Furthermore, the durability of Husqvarna’s construction means these machines can withstand the rigors of daily use, making them a worthwhile investment for any user.

In conclusion, the Husqvarna 11 and 13 series, including the Bio variants, stand out in the market for their thoughtful design and innovative technology. These models demonstrate Husqvarna's dedication to creating efficient, powerful, and environmentally friendly equipment that meets the diverse needs of users everywhere. Whether you are a professional landscaper or a dedicated homeowner, the Husqvarna 11 and 13 series deliver performance, reliability, and sustainability.
Top Page Image Contents