Husqvarna 966614001, 967004001, PZ5430, PZ5426FX Rollover Protection System Rops, Spark Arrestors

Page 17

SAFETY

Rollover Protection System (ROPS)

The ROPS increases the basic weight of the unit by 73 lbs/33 kg.

Do not use ROPS as a lifting, attaching or anchoring point.

Do not use ROPS for wrecking or towing.

Do not exceed Max GVW: 2822 lbs/1283 kg.

Read machine’s operator manual before each use.

Securely fasten the seat belt if the unit has a ROPS.

Where possible, avoid operating the unit near ditches, embankments and holes.

Reduce speed when turning, crossing slopes and on rough, slick or muddy surfaces.

Stay off slopes too steep for safe operation.

Watch where you are going, especially at row ends, on roads and around trees.

Do not permit others to ride.

Operate the mower smoothly - no jerky turns, starts or stops.

When mower is stopped, set brakes securely and use park brake.

If any part of ROPS is damaged, the entire ROPS must be replaced.

Check all bolts including seat belt for correct torque before each use.

Check ROPS structure for damage before each use.

ROPS bar is NOT intended for use in sub zero temperatures.

WARNING!

The rollover protection system's capabilities may be impaired by damage if the mower is overturned or if alteration to the ROPS occurs. If these conditions take place, the total structure MUST be replaced.

WARNING!

This mower is equipped with an internal combustion engine and should not be used on or near any unimproved forested, bush covered or grassy lands unless the engine's system is equipped with a spark arrester meeting applicable local or state laws (if any). If a spark arrestor is used, it should be maintained

in effective working order by the operator.

Spark Arrestors

A spark arrester is standard equipment on the unit and is attached to the engine muffler. Clean the interior screen regularly, depending on usage and conditions.

To clean, remove the clamp securing the tail pipe. Remove the tail pipe and slide the spark arrestor screen out of the muffler. Clean carbon from the screen with a soft brush or cloth.

Replace screen and reattach the tail pipe, orienting the tail pipe either horizontally or upwards, away from grassy surfaces.

8011-514

Regularly clean spark arrestor screen

17

Image 17
Contents Operator Manual All rights reserved Contents Page Introduction Manufacturing Number Good ServiceXxxx xxxxxx xxxxx xxxx Xxxxxx xxxxxxxxx. xx xxxxxxxx Symbols and DecalsRemove key before Performing any General Operation SafetySafety Instructions Never take passengers Slope Operation Personal Safety EquipmentBe extra cautious when driving on slopes Safe Handling of Gasoline General Maintenance Risk of sparking Transport Spark Arrestors Rollover Protection System RopsControl Locations ControlsMotion Control Levers Throttle Control Blade SwitchParking Brake Ignition Switch Hour Meter Choke ControlFuses Cutting Height Pedals Tracking KnobFuel Shut Off Valve Seat Adjustment LeverSeat should not be adjusted while unit is in motion Fuel Tank Steering OperationTraining Before Starting Roll Bar and Safety BeltStarting the Engine Set the throttle Open the fuel tank valve Set the engine speed To remove cables, reverse order Weak BatteryJumper Cables Use Running Operating on Hills Mowing Tips Stopping the Engine Bypass Valves Moving Machine By HandMaintenance Maintenance For replacing BatteryFor cleaning Tire Pressures Safety SystemFuel Filter Parking brake adjustment Measure gap Deck Belt Removal Deck Belt InstallationDeck Belt Pump Belt Belt InstallationBelts Replacing Pump BeltCutting Blades Leveling Deck Adjusting the Mower DeckCaster Wheels Removal and InstallationAnti-scalp Rollers Deck Lift SpringHardware CleaningUse protective glasses when cleaning and washing General LubricationLubrication Schedule Cables Wheel and Deck ZerksFront Wheel Mount Front Wheel BearingsFluid and Filter Change Hydraulic DriveTransmission Purging Procedures Problem Cause TroubleshootingTroubleshooting Winter Storage ServiceStorage Wiring Diagram Transmission Technical DataPZ 5426FX PZ5430 Engine PZ 5426FX PZ5430 Frame DimensionMetric Standard Hardware Torque SpecificationsStandard Hardware USA requirements Conformity CertificatesDelivery Service Service JournalAfter 10 hours Daily Service Hour Service Service Journal Service Journal At Least Once Each Year Service Journal Service Journal Page 115 461527 Rev B 2011-12-2