Husqvarna 966616701, PZ29D CE manual Battery, For cleaning, For replacing

Page 40

MAINTENANCE

Battery

The mower is equipped with a maintenance free battery and does not need servicing. However, periodic charging of the battery with an automotive type battery charger will extend its life.

Keep battery and terminals clean.

Keep battery bolts tight.

See chart for charging times.

WARNING!

Always wear eye protection when around batteries.

Battery Removal

Corrosion and dirt on the battery and terminals can cause the battery to “leak” power.

1.Lift the seat and rotate fully forward until supported by the seat rod.

2.Loosen the two wingnuts attached to the side “J” bolts just enough that the battery mount bracket slides down off the battery.

3.Using two ½" wrenches disconnect BLACK battery cable then RED battery cable.

4.Carefully remove the battery from the mower.

For cleaning

5.Rinse the battery with plain water and dry.

6.Clean terminals and battery cable ends with wire brush until shiny.

For replacing

7.Install new battery with terminals in the same position as the old battery.

8.Connect RED battery cable first to positive (+) battery terminal.

9.Connect BLACK grounding cable to negative (-) battery terminal.

10.Slide mount bracket back up over battery and retighten wingnuts.

11.Lower seat.

STANDARD

STATE

APPROXIMATE BATTERY CHARGING TIME*

 

 

TO FULL CHARGE AT 80OF / 27OC

BATTERY

OF

 

 

 

 

 

Maximum Rate at:

 

 

 

 

 

 

CHARGE

 

 

 

 

 

50 Amps

30 Amps

20 Amps

10 Amps

 

 

 

 

 

 

 

 

12.6V

100%

- FULL CHARGE -

 

 

 

 

 

 

12.4V

75%

20 min.

35 min.

48 min.

90 min.

 

 

 

 

 

 

12.2V

50%

45 min.

75 min.

95 min.

180 min.

 

 

 

 

 

 

12.0V

25%

65 min.

115 min.

145 min.

280 min.

 

 

 

 

 

 

11.8V

0%

85 min.

150 min.

195 min.

370 min.

 

 

 

 

 

 

*Charging time depends on battery capacity,

condition, age, temperature and efficiency of charger

IMPORTANT INFORMATION

Do not attempt to open or remove caps or covers. Adding or checking level of electrolyte is not necessary.

Always use two wrenches for the terminal screws.

WARNING!

Do not short battery terminals by allowing a wrench or any other object to contact both terminals at the same time. Before connecting battery, remove metal bracelets, wristwatch bands, rings, etc.

Positive terminal must be connected first to prevent sparks from accidental grounding.

1

2

8065-020

1.Mount bracket

2.Battery bracket

Battery cleaning and installation

40

Image 40
Contents Operator Manual 2011 HTC. All rights reserved Orangeburg, SC Contents Page Introduction Good Service Manufacturing NumberSymbols and Decals Important InformationRemove key before Performing any Safety Instructions SafetyGeneral Operation Never take passengers Personal Safety Equipment Slope OperationBe extra cautious when driving on slopes Safe Handling of Diesel Fuel General Maintenance Risk of sparking Transport Rollover Protection System Rops Spark ArrestorControls Control LocationsMotion Control Levers Blade Switch Parking BrakeHour Meter Tracking KnobIgnition Switch Battery Voltage Coolant TemperatureControl Module Oil PressureSeat Adjustments Cutting Height PedalsFuel Shut Off Valve FusesPump Release Valves Fuel Tanks Training OperationSteering Roll Bar and Safety Belt Before StartingStarting the Engine Set the throttle Turn the key to RUN and observe glow plug light Jumper Cables Use Weak BatteryTo remove cables, reverse order Running Operating on Hills Stopping the Engine Mowing Tips Moving Machine By Hand Pump Release ValvesMaintenance Engine and RadiatorMaintenance For cleaning BatteryFor replacing Fuel Filter Safety SystemTire Pressures Parking brake adjustment Height Adjustment Drive Lever AdjustmentAlignment Deck Belt Deck Belt InstallationDeck Belt Removal Pump Belt Belt Removal/InstallationReplacing Pump Belt Reinstallation Clutch BeltBelts RemovalCutting Blades Adjusting the Mower Deck Leveling DeckRemoval and Installation Caster WheelsAnti-scalp Rollers Deck Lift SpringUse protective glasses when cleaning and washing CleaningHardware Lubrication Schedule LubricationGeneral Wheel and Deck Zerks Front Wheel MountFront Wheel Bearings Deck SpindleHydraulic Drive Fluid and Filter ChangeTransmission Purging Procedures Troubleshooting Guide Problem CauseTroubleshooting Guide Storage ServiceWinter Storage Wiring Diagram Technical Data Torque SpecificationsHex Head Cap Screws Standard HardwareEngine TransmissionDimension Combi Deck Flat Deck FrameVibrations Noise EmissionsConformity Certificates Conformity Certificates For Model Listed BelowUSA requirements EU Declaration of Conformity InformationService Journal Delivery ServiceAfter 10 hours Daily Service Hour Service Service Journal Service Journal At Least Once Each Year Service Journal Page 115 404727 Rev B Original Instructions 2011-11-30

PZ29D CE, 966616701 specifications

The Husqvarna 966616701, PZ29D CE, stands out as a premier choice among professional-grade zero-turn mowers, designed to cater to the needs of both landscape professionals and avid homeowners. Known for its powerful performance and innovative technology, the PZ29D CE showcases impressive features that enhance efficiency and durability.

At the heart of the PZ29D CE is a robust engine capable of delivering high power output, allowing users to tackle tough mowing tasks with ease. Typically equipped with a reliable Kawasaki engine, this mower ensures consistent performance, reducing downtime and enhancing productivity. The engine’s design focuses on fuel efficiency without compromising power, which is crucial for extensive mowing applications.

One of the standout features of the Husqvarna PZ29D CE is its cutting deck. The mower often features a wide cutting deck that ranges from 52 to 60 inches, depending on the specific model. This breadth of cutting gets the job done quickly, allowing operators to cover large areas in a short time. Additionally, the deck design often incorporates advanced air flow technology that can produce a clean and even cut, even in varied grass conditions.

The zero-turn capability of the PZ29D CE enhances maneuverability significantly, allowing for tight turns and easy navigation around obstacles. This feature is essential for professional landscapers who need to maintain precision while working around trees, flower beds, and fences. The intuitive controls make it easy for users to handle the mower, ensuring a smooth operational experience.

Comfort is also a priority in the design of the PZ29D CE. The plush, adjustable seat provides ample support during long hours of mowing, while the ergonomic control layout minimizes fatigue for the operator. This design consideration is vital for those who rely on their equipment for extended periods.

Additionally, the Husqvarna PZ29D CE incorporates features for improved safety, including roll-over protection systems and safety switches that engage when the operator leaves the seat.

In conclusion, the Husqvarna 966616701, PZ29D CE, combines powerful performance, advanced cutting technology, and operator comfort, making it a reliable and efficient choice for those seeking a high-performing zero-turn mower. Whether for commercial landscaping or residential maintenance, this model exemplifies the very best in lawn care technology.