Husqvarna 966616701, PZ29D CE manual Parking brake adjustment

Page 42

MAINTENANCE

Parking Brake

Visually check that no damage is found on the lever, links, or switch belonging to the parking brake. Perform a standstill test and check that there is sufficient braking action.

WARNING!

Faulty adjustment result in reduced braking ability and can cause an accident.

IMPORTANT INFORMATION

The machine must be standing still when applying the parking brake.

Parking Brake Adjustments

1.Using a jack stand, raise the rear of the mower up off the ground. Make sure the machine is securely supported.

2.Remove the rear tire assemblies.

3.Release the park brake.

4.Loosen the jam nuts from rear of the brake bracket approximately ½" (13mm).

5.Loosen the nyloc nut until the threads on the linkage are flush with the end of the nut.

6.Engage the park brake lever.

7.Pull forward on the linkage until it stops against the brake on the wheel motor. Be sure the linkage is not stopping against the jam nuts.

8.Tighten the nyloc nut against spring until the spring no longer rotates freely.

9.Turn the jam nuts until the front nut is 1/8" to 3/16" from the brake bracket.

10.Tighten the rear jam nut against the front nut.

11.Tighten the nyloc nut against the spring and brake bracket until the gap set in Step 9 is closed.

12.Repeat the above steps on other side of the unit.

13.Disengage and reengage the brake lever to test braking.

14.Reinstall the drive tire assemblies.

15.Remove jack and jack stands.

8065-006

Parking brake

2

1/8 - 3/16"

 

4

3

 

 

1

 

8065-078

1.Jam nuts

2.Brake bracket

3.Nyloc nut

4.Brake linkage

Parking brake adjustment

42

Image 42
Contents Operator Manual 2011 HTC. All rights reserved Orangeburg, SC Contents Page Introduction Good Service Manufacturing NumberSymbols and Decals Important InformationRemove key before Performing any Safety Safety InstructionsGeneral Operation Never take passengers Personal Safety Equipment Slope OperationBe extra cautious when driving on slopes Safe Handling of Diesel Fuel General Maintenance Risk of sparking Transport Rollover Protection System Rops Spark ArrestorControls Control LocationsMotion Control Levers Blade Switch Parking BrakeHour Meter Tracking KnobIgnition Switch Control Module Battery VoltageCoolant Temperature Oil PressureSeat Adjustments Cutting Height PedalsFuses Fuel Shut Off ValvePump Release Valves Fuel Tanks Operation TrainingSteering Roll Bar and Safety Belt Before StartingStarting the Engine Set the throttle Turn the key to RUN and observe glow plug light Weak Battery Jumper Cables UseTo remove cables, reverse order Running Operating on Hills Stopping the Engine Mowing Tips Moving Machine By Hand Pump Release ValvesMaintenance Engine and RadiatorMaintenance Battery For cleaningFor replacing Safety System Fuel FilterTire Pressures Parking brake adjustment Drive Lever Adjustment Height AdjustmentAlignment Deck Belt Installation Deck BeltDeck Belt Removal Belt Removal/Installation Pump BeltReplacing Pump Belt Belts ReinstallationClutch Belt RemovalCutting Blades Adjusting the Mower Deck Leveling DeckAnti-scalp Rollers Removal and InstallationCaster Wheels Deck Lift SpringCleaning Use protective glasses when cleaning and washingHardware Lubrication Lubrication ScheduleGeneral Front Wheel Bearings Wheel and Deck ZerksFront Wheel Mount Deck SpindleHydraulic Drive Fluid and Filter ChangeTransmission Purging Procedures Troubleshooting Guide Problem CauseTroubleshooting Guide Service StorageWinter Storage Wiring Diagram Hex Head Cap Screws Technical DataTorque Specifications Standard HardwareEngine TransmissionVibrations DimensionCombi Deck Flat Deck Frame Noise EmissionsUSA requirements Conformity CertificatesConformity Certificates For Model Listed Below EU Declaration of Conformity InformationService Journal Delivery ServiceAfter 10 hours Daily Service Hour Service Service Journal Service Journal At Least Once Each Year Service Journal Page 115 404727 Rev B Original Instructions 2011-11-30

PZ29D CE, 966616701 specifications

The Husqvarna 966616701, PZ29D CE, stands out as a premier choice among professional-grade zero-turn mowers, designed to cater to the needs of both landscape professionals and avid homeowners. Known for its powerful performance and innovative technology, the PZ29D CE showcases impressive features that enhance efficiency and durability.

At the heart of the PZ29D CE is a robust engine capable of delivering high power output, allowing users to tackle tough mowing tasks with ease. Typically equipped with a reliable Kawasaki engine, this mower ensures consistent performance, reducing downtime and enhancing productivity. The engine’s design focuses on fuel efficiency without compromising power, which is crucial for extensive mowing applications.

One of the standout features of the Husqvarna PZ29D CE is its cutting deck. The mower often features a wide cutting deck that ranges from 52 to 60 inches, depending on the specific model. This breadth of cutting gets the job done quickly, allowing operators to cover large areas in a short time. Additionally, the deck design often incorporates advanced air flow technology that can produce a clean and even cut, even in varied grass conditions.

The zero-turn capability of the PZ29D CE enhances maneuverability significantly, allowing for tight turns and easy navigation around obstacles. This feature is essential for professional landscapers who need to maintain precision while working around trees, flower beds, and fences. The intuitive controls make it easy for users to handle the mower, ensuring a smooth operational experience.

Comfort is also a priority in the design of the PZ29D CE. The plush, adjustable seat provides ample support during long hours of mowing, while the ergonomic control layout minimizes fatigue for the operator. This design consideration is vital for those who rely on their equipment for extended periods.

Additionally, the Husqvarna PZ29D CE incorporates features for improved safety, including roll-over protection systems and safety switches that engage when the operator leaves the seat.

In conclusion, the Husqvarna 966616701, PZ29D CE, combines powerful performance, advanced cutting technology, and operator comfort, making it a reliable and efficient choice for those seeking a high-performing zero-turn mower. Whether for commercial landscaping or residential maintenance, this model exemplifies the very best in lawn care technology.