Husqvarna PZ29D CE, 966616701 manual Winter Storage, Service

Page 57

STORAGE

Winter Storage

The machine should be readied for storage at the end of the mowing season or if it will not be in use for longer than 30 days.

Fuel allowed to stand for long periods of time (30 days or more) can leave sticky residues that can plug the injector and disrupt engine function.

Fuel stabilizers are an acceptable option as regards to the sticky residues that can occur during storage.

Add stabilizer to the fuel in the tank or in the storage container. Always use the mixing ratios specified by the manufacturer of the stabilizer. Run the engine for at least 10 minutes after adding the stabilizer so that it reaches the injector. Do not empty the fuel tank and the injector if a stabilizer has been added.

WARNING!

Never store an engine with fuel in the tank indoors or in poorly ventilated spaces where fuel vapor can come in contact with open flames, sparks, or a pilot light such as in a boiler, hot water tank, clothes drier, etc. Handle the fuel with care. It is very flammable and can cause serious personal injury and property damage. Drain the fuel into an approved container outdoors and far away from open flame. Never use diesel fuel for cleaning. Use

a degreaser and warm water.

To ready the machine for storage, follow these steps:

1.Thoroughly clean the machine, especially under the mower deck. Touch up damage to the paint and spray a thin layer of oil on the underside of the mower deck to avoid corrosion.

2.Inspect the machine for worn or damaged parts and tighten any nuts or screws that may have become loose.

3.Change the engine oil; dispose of properly.

4.Empty the fuel tanks or add a fuel stabilizer. Start the engine and allow it to run until the injector is drained of fuel or the stabilizer has reached the injector.

5.Lubricate all grease zerks, joints, and axles.

6.Remove the battery. Clean, charge, and store the battery in a cool place, but protect it from direct cold.

7.Store the machine in a clean, dry place and cover it for extra protection.

Service

When ordering spare parts, please specify the purchase year, model, type, and serial number.

Always use genuine Husqvarna spare parts.

An annual check-up at an authorized service workshop is a good way to ensure that the machine performs its best the following season.

57

Image 57
Contents Operator Manual 2011 HTC. All rights reserved Orangeburg, SC Contents Page Introduction Manufacturing Number Good ServiceImportant Information Symbols and DecalsRemove key before Performing any Safety Safety InstructionsGeneral Operation Never take passengers Slope Operation Personal Safety EquipmentBe extra cautious when driving on slopes Safe Handling of Diesel Fuel General Maintenance Risk of sparking Transport Spark Arrestor Rollover Protection System RopsControl Locations ControlsMotion Control Levers Parking Brake Blade SwitchTracking Knob Hour MeterIgnition Switch Coolant Temperature Battery VoltageControl Module Oil PressureCutting Height Pedals Seat AdjustmentsFuses Fuel Shut Off ValvePump Release Valves Fuel Tanks Operation TrainingSteering Before Starting Roll Bar and Safety BeltStarting the Engine Set the throttle Turn the key to RUN and observe glow plug light Weak Battery Jumper Cables UseTo remove cables, reverse order Running Operating on Hills Stopping the Engine Mowing Tips Pump Release Valves Moving Machine By HandEngine and Radiator MaintenanceMaintenance Battery For cleaningFor replacing Safety System Fuel FilterTire Pressures Parking brake adjustment Drive Lever Adjustment Height AdjustmentAlignment Deck Belt Installation Deck BeltDeck Belt Removal Belt Removal/Installation Pump BeltReplacing Pump Belt Clutch Belt ReinstallationBelts RemovalCutting Blades Leveling Deck Adjusting the Mower DeckCaster Wheels Removal and InstallationAnti-scalp Rollers Deck Lift SpringCleaning Use protective glasses when cleaning and washingHardware Lubrication Lubrication ScheduleGeneral Front Wheel Mount Wheel and Deck ZerksFront Wheel Bearings Deck SpindleFluid and Filter Change Hydraulic DriveTransmission Purging Procedures Problem Cause Troubleshooting GuideTroubleshooting Guide Service StorageWinter Storage Wiring Diagram Torque Specifications Technical DataHex Head Cap Screws Standard HardwareTransmission EngineCombi Deck Flat Deck Frame DimensionVibrations Noise EmissionsConformity Certificates For Model Listed Below Conformity CertificatesUSA requirements EU Declaration of Conformity InformationDelivery Service Service JournalAfter 10 hours Daily Service Hour Service Service Journal Service Journal At Least Once Each Year Service Journal Page 115 404727 Rev B Original Instructions 2011-11-30

PZ29D CE, 966616701 specifications

The Husqvarna 966616701, PZ29D CE, stands out as a premier choice among professional-grade zero-turn mowers, designed to cater to the needs of both landscape professionals and avid homeowners. Known for its powerful performance and innovative technology, the PZ29D CE showcases impressive features that enhance efficiency and durability.

At the heart of the PZ29D CE is a robust engine capable of delivering high power output, allowing users to tackle tough mowing tasks with ease. Typically equipped with a reliable Kawasaki engine, this mower ensures consistent performance, reducing downtime and enhancing productivity. The engine’s design focuses on fuel efficiency without compromising power, which is crucial for extensive mowing applications.

One of the standout features of the Husqvarna PZ29D CE is its cutting deck. The mower often features a wide cutting deck that ranges from 52 to 60 inches, depending on the specific model. This breadth of cutting gets the job done quickly, allowing operators to cover large areas in a short time. Additionally, the deck design often incorporates advanced air flow technology that can produce a clean and even cut, even in varied grass conditions.

The zero-turn capability of the PZ29D CE enhances maneuverability significantly, allowing for tight turns and easy navigation around obstacles. This feature is essential for professional landscapers who need to maintain precision while working around trees, flower beds, and fences. The intuitive controls make it easy for users to handle the mower, ensuring a smooth operational experience.

Comfort is also a priority in the design of the PZ29D CE. The plush, adjustable seat provides ample support during long hours of mowing, while the ergonomic control layout minimizes fatigue for the operator. This design consideration is vital for those who rely on their equipment for extended periods.

Additionally, the Husqvarna PZ29D CE incorporates features for improved safety, including roll-over protection systems and safety switches that engage when the operator leaves the seat.

In conclusion, the Husqvarna 966616701, PZ29D CE, combines powerful performance, advanced cutting technology, and operator comfort, making it a reliable and efficient choice for those seeking a high-performing zero-turn mower. Whether for commercial landscaping or residential maintenance, this model exemplifies the very best in lawn care technology.