Husqvarna 96045000407 owner manual To Level Mower

Page 20

SERVICE AND ADJUSTMENTS

TO LEVEL MOWER

Make sure tires are properly inflated to the PSI shown on tires. If tires are over or under inflated, it may affect the appearance of your lawn and lead you to think the mower is not adjusted properly.

VISUAL SIDE-TO-SIDE ADJUSTMENT (See Fig. 23)

With all tires properly inflated and if your lawn appears unevenly cut, determine which side of mower is cutting lower.

NOTE: As desired, you can raise the low side of mower or lower the high side.

Go to side of mower you wish to adjust.

With a 3/4" or adjustable wrench, turn lift link adjust- ment nut (A) to the left to lower the mower, or, to the right to raise the mower.

 

A

Turn nut right

Turn nut left

to raise mower

to lower mower

FIG. 23

NOTE: Each full turn of adjustment nut will change mower height about 3/16".

Test your adjustment by mowing some uncut grass and visually checking the appearance. Readjust, if necessary, until you are satisfied with the results.

PRECISION SIDE-TO-SIDE ADJUSTMENT (See Fig. 24)

With all tires properly inflated, park tractor on level ground or driveway.

CAUTION: Blades are sharp. Protect your hands with gloves and/or wrap blade with heavy cloth.

Raise mower to its highest position.

At both sides of mower, position blade at side and measure the distance (A) from bottom edge of blade to the ground. The distance should be the same on both sides.

 

02966

A

A

FIG. 24

If adjustment is necessary, see steps in Visual Adjust- ment instructions above.

Recheck measurements, adjust if necessary until both sides are equal.

FRONT-TO-BACK ADJUSTMENT (See Figs. 25A and 25B) IMPORTANT: Deck must be level side-to-side.

To obtain the best cutting results, the mower blades should be adjusted so the front tip is 1/8" to 1/2" lower than the rear tip when the mower is in its highest position.

CAUTION: Blades are sharp. Protect your hands with gloves and/or wrap blade with heavy cloth.

Raise mower to highest position.

Position any blade so the tip is pointing straight forward. Measure distance (B) to the ground at front and rear tip of the blade.

If front tip of blade is not 1/8" to 1/2" lower than the rear tip, go to the front of tractor.

With an 11/16" or adjustable wrench, loosen jam nut A several turns to clear adjustment nut B.

With a 3/4" or adjustable wrench, turn front link adjust- ment nut (B) clockwise (ltighten) to raise the front of mower, or, counterclockwise (loosen) to lower the front mower.

02548

BB

FIG. 25A

B

A

Tighten adjust

Loosen adjust

nut B to raise

nut B to lower

mower

mower

02950

 

Loosen jam nut A first

 

FIG. 25B

NOTE: Each full turn of the adjustment nut will change mower height about 1/8".

Recheck measurements, adjust if necessary until front tip of blade is 1/8" to 1/2" lower than the rear tip.

Hold adjustment nut in position with wrench and tighten jam nut securely against adjustment nut.

20

Image 20
Contents YTH20K46 Safety Rules Safe Operation Practices for Ride-On MowersGeneral Operation II. Slope OperationService General ServiceIII. Children IV. TowingTable of Contents Assembly Unassembled PartsTo Remove Tractor from Carton Unpack CartonCheck Tire Pressure Check Deck LevelnessCheck for Proper Position of ALL Belts Check Brake SystemOperation Know Your Tractor HOW to USE Your Tractor Attachment Clutch Switch Disengaged EngagedTo SET Parking Brake See Fig Stopping See aTo Adjust Mower Cutting Height See Fig To Adjust Gauge Wheels See FigSystem Characteristics To Move Forward and Backward See FigTo Operate Mower See Fig Reverse Operation System ROS See FigTo Operate on Hills To Transport See FigsService REMINDER/HOUR Meter Before Starting the EngineCheck Engine OIL Level ADD GasolineMowing Tips Purge TransmissionMaintenance Lubrication ChartBattery TractorBlade Care Blade Removal See FigEngine BeltsTransaxle Cooling Transaxle Pump FluidCleaning Service and Adjustments To Install Mower See FigsTo Remove Mower See Fig Slide mower out from under right side of tractorInstall belt on engine pulley M To Level Mower Belt Installation To Replace Mower Blade Drive Belt See FigTo Check Brake To Replace Motion Drive Belt See FigTo Adjust Steering Wheel Alignment To Start Engine with a Weak Battery See FigFront Wheel TOE-IN/CAMBER To Remove Wheel for Repairs See FigTransmission Storage OtherFuel System Engine OILTroubleshooting Points Problem Cause CorrectionEngine dies when Schematic Tractor - Model Number YTH20K46 96045000407, Product no 45Electrical KEY Part Description Chassis 196 532 41 45-80Console Asm. Deck Lift 817 60Drive Drive 817 49Spark Arrester KIT EngineEngine Kohler Model No. SV620 Steering Assembly 532 19 Wheel, Steering Axle Cast Iron Decals Wheels and TiresSeat Assembly 532 40 Seat145 Mower Deck195 KEY Part NO. no Description Mower Lift 100Limited Warranty Husqvarna S Obligations Under the Warranty 532 42 20-52 07.30.08 AP

96045000407 specifications

The Husqvarna 96045000407, a powerful and versatile lawn mower, is designed to provide efficiency and superior cutting performance, making it an ideal choice for both residential and professional landscaping. This model features a robust engine that guarantees reliability and power for any mowing task, ensuring a clean and precise cut every time.

One of the standout features of the Husqvarna 96045000407 is its innovative cutting deck design. The mower is equipped with a 42-inch cutting deck that allows for wide, efficient coverage while mowing, reducing the time and effort needed to complete large areas. This deck is crafted from high-quality steel, ensuring durability and long-lasting performance. The adjustable cutting height options give users the flexibility to achieve their desired grass length, promoting a healthy and well-groomed lawn.

Incorporating advanced technology, the Husqvarna 96045000407 employs a robust and efficient engine that provides excellent torque and power, making it suitable for various terrains. The mower's ease of starting is a key feature, thanks to its air-cooled engine that also contributes to reduced emissions and fuel consumption, making it an environmentally friendly choice for lawn care enthusiasts.

Another significant advantage of the Husqvarna 96045000407 is its user-friendly design. With intuitive controls, operators can easily navigate and operate the mower without hassle. The ergonomically designed handle enhances comfort during prolonged use, allowing for better maneuverability. Additionally, this model includes large rear wheels that facilitate easy movement over uneven ground, improving stability and traction.

Versatility is further enhanced by the optional mulching kit, which allows for the clippings to be finely chopped and returned to the lawn as a natural fertilizer, promoting healthy growth. The Husqvarna 96045000407 is not just a mower; it’s a comprehensive lawn care solution tailored for those who demand quality and efficiency in their gardening tasks.

Overall, the Husqvarna 96045000407 stands out with its combination of power, durability, and advanced features. Whether you are a homeowner looking to maintain your lawn or a professional seeking a reliable mowing solution, this model is equipped with the technology and engineering to meet and exceed your expectations, making it a valuable addition to any landscaping toolkit.