Husqvarna 96045001900 owner manual Tractor, Blade Care, Brake Operation, Tires, Battery

Page 15

MAINTENANCE

TRACTOR

Always observe safety rules when performing any main- tenance.

BLADE CARE

For best results mower blades must be sharp. Replace worn, bent or damaged blades.

BRAKE OPERATION

If tractor requires more than five (5) feet to stop at highest speed in highest gear on a level, dry concrete or paved surface, then brake must be serviced. (See “TO CHECK BRAKE” in the Service and Adjustments section of this manual).

TIRES

•Maintain proper air pressure in all tires (See PSI on tires).

•Keep tires free of gasoline, oil, or insect control chemi- cals which can harm rubber.

•Avoid stumps, stones, deep ruts, sharp objects and other hazards that may cause tire damage.

NOTE: To seal tire punctures and prevent flat tires due to slow leaks, tire sealant may be purchased from your local parts dealer. Tire sealant also prevents tire dry rot and corrosion.

OPERATOR PRESENCE SYSTEM AND REVERSE OP- ERATION SYSTEM (ROS) (See Fig. 14)

Be sure operator presence and reverse operation systems are working properly. If your tractor does not function as described, repair the problem immediately.

•The engine should not start unless the brake pedal is fully depressed, and the attachment clutch control is in the disengaged position.

CHECK OPERATOR PRESENCE SYSTEM

•When the engine is running, any attempt by the operator to leave the seat without first setting the parking brake should shut off the engine.

•When the engine is running and the attachment clutch is engaged, any attempt by the operator to leave the seat should shut off the engine.

•The attachment clutch should never operate unless the operator is in the seat.

ROS "ON" Position

Engine "ON" Position

(Normal Operating)

 

02828

Fig. 14

CHECK REVERSE OPERATION (ROS) SYSTEM

• When the engine is running with the ignition switch in the engine "ON" position and the attachment clutch engaged, any attempt by the operator to shift into reverse should shut off the engine.

• When the engine is running with the ignition switch in the ROS "ON" position and the attachment clutch en- gaged, any attempt by the operator to shift into reverse should NOT shut off the engine.

15

CAUTION: Use only a replacement blade approved by the manufacturer of your tractor. Using a blade not approved by the manufacturer of your tractor is hazardous, could damage your tractor and void your warranty.

BLADE REMOVAL (See Fig. 15)

•Raise mower to highest position to allow access to blades.

NOTE: Protect your hands with gloves and/or wrap blade with heavy cloth.

•Remove blade bolt by turning counterclockwise.

•Install new blade with stamped "GRASS SIDE" facing the ground.

IMPORTANT: To ensure proper assembly, center hole in blade must align with star on mandrel assembly.

•Install and tighten blade bolt securely (45-55 Ft. Lbs. torque).

IMPORTANT: Special blade bolt is heat treated.

 

Blade

Blade Bolt

Mandrel

(Special)

Assembly

 

Star

 

Center Hole

Fig. 15

BATTERY

Your tractor has a battery charging system which is sufficient for normal use. However, periodic charging of the battery with an automotive charger will extend its life.

•Keep battery and terminals clean.

•Keep battery bolts tight.

•Keep small vent holes open.

•Recharge at 6-10 amperes for 1 hour.

NOTE: The original equipment battery on your tractor is maintenance free. Do not attempt to open or remove caps or covers. Adding or checking level of electrolyte is not necessary.

Page 14 Page 16
Image 15
Page 14 Page 16
Contents YTH2348 II. Slope Operation Safety RulesSafe Operation Practices for Ride-On Mowers General OperationService III. ChildrenIV. Towing Table of Contents To Remove Tractor from Carton AssemblyTools Required for Assembly Unassembled PartsCheck Brake System Check Tire PressureCheck Deck Levelness Check for Proper Position of ALL BeltsOperation Reverse Operation System ROS on Position Know Your TractorTo USE Throttle Control D See Fig HOW to USE Your TractorTo SET Parking Brake See Fig StoppingTo USE Cruise Control J See Fig To Adjust Mower Cutting Height See FigTo Adjust Gauge Wheels See Fig To Move Forward and Backward See FigTo Operate on Hills Service REMINDER/HOUR MeterUsing the Reverse Operation System Reverse Operation System ROS See FigTo Start Engine See Fig Before Starting the EngineCheck Engine OIL Level ADD GasolinePurge Transmission Mowing TipsLubrication Chart MaintenanceBrake Operation BatteryTractor Blade CareTransaxle Pump Fluid EngineBelts Transaxle CoolingCleaning Service and Adjustments To Install Mower See FigsTo Remove Mower See Fig First Install ANTI-SWAY BAR S LBF To Level Mower Mower Drive Belt Installation To Replace Mower Blade Drive Belt See FigMower Drive Belt Removal Front Wheel TOE-IN/CAMBER Belt InstallationTo Replace Motion Drive Belt See Fig To Check BrakeTo Attach Jumper Cables To Start Engine with a Weak BatteryReplacing Battery See Fig To Remove Wheel for Repairs See FigTo Replace Headlight Bulb To Adjust Throttle Control CableTo Adjust Choke Control To Adjust CarburetorEngine OIL StorageOther Fuel SystemTroubleshooting Points Engine dies when Tractor Model NO. YTH2348 96045001900, Product no 45 SchematicElectrical KEY Part Description Chassis Tractor Model NO. YTH2348 96045001900, Product no 45 197 196 DriveTractor Model NO. YTH2348 96045001900, Product no 45 Spark Arrester KIT Engine1837 Engine Power Rating Information Steering Assembly 532 40 Seat Seat AssemblyMower Deck 532 40 Deck Weldment Mower Mower Lift Wheels and Tires DecalsService Notes Service Notes Service Notes Suggested Guide for Sighting Slopes for Safe Operation Warranty Statement

96045001900 specifications

The Husqvarna 96045001900 is a versatile and robust chainsaw designed to meet the demands of both professionals and enthusiasts in the field of forestry and landscaping. Its powerful engine and advanced features make it an ideal choice for various cutting tasks, whether for maintenance, tree felling, or pruning.

One of the standout features of this chainsaw is its high-performance engine. The Husqvarna 96045001900 is equipped with a reliable and efficient 50.2cc engine, which delivers exceptional power and speed. This engine not only provides the necessary torque for cutting through tough materials but also ensures that users can complete their tasks with minimal effort.

The chainsaw boasts a lightweight design, which enhances maneuverability without sacrificing durability. Weighing in at just about 11 lbs, it allows users to handle it with ease during extended periods of operation. The ergonomic handle contributes to this comfort, offering a secure grip that reduces fatigue, especially during larger jobs.

Another essential aspect of the Husqvarna 96045001900 is its advanced air filtration system. This feature helps in maintaining engine performance by keeping dust and debris out of the engine, thereby prolonging its lifespan and reducing maintenance needs. In addition, the chainsaw is designed with an automatic oiling system, ensuring that the chain is consistently lubricated for optimal performance.

The chainsaw also incorporates Husqvarna’s unique X-Torq technology, which reduces fuel consumption and minimizes exhaust emissions. This environmentally friendly innovation not only contributes to lower operating costs but also meets stringent emission regulations, making it suitable for use in eco-sensitive areas.

Safety features are paramount in the design of the Husqvarna 96045001900. It comes equipped with a chain brake that stops the chain immediately in case of kickback, ensuring user safety. Furthermore, the front hand guard and throttle lockout prevent accidental starts and provide additional protection while operating the saw.

In conclusion, the Husqvarna 96045001900 is a high-quality chainsaw that excels in power, efficiency, and safety. With its powerful engine, lightweight construction, advanced air filtration, and cutting-edge technologies, it stands out as a top choice for anyone looking to tackle tough cutting jobs with ease and confidence. Whether for professional forestry work or home landscaping projects, this chainsaw delivers performance and reliability that make it a worthy investment.
Top Page Image Contents