Husqvarna 96045001900 To Replace Motion Drive Belt See Fig, To Check Brake, Belt Removal

Page 23

SERVICE AND ADJUSTMENTS

TO REPLACE MOTION DRIVE BELT (See Fig. 35)

Park the tractor on level surface. Engage parking brake. For assistance, there is a belt installation guide decal on bottom side of left footrest.

BELT REMOVAL -

•Remove mower (See “TO REMOVE MOWER” in this section of manual).

NOTE: Observe entire motion drive belt and position of all belt guides and keepers.

•Disconnect clutch wire harness (A).

•Remove anti-rotation link (B) on right side of tractor.

•Remove belt from stationary idler (C) and clutching idler (D).

•Remove belt from centerspan idler (E).

•Pull belt slack toward rear of tractor. Carefully remove belt upwards from transmission input pulley and over cooling fan blades (F).

•Remove belt downward from engine pulley and around electric clutch (G).

•Slide belt toward rear of tractor, off the steering plate

(H) and remove from tractor.

 

 

G

 

 

H

B

A

 

 

 

 

C

J

 

 

 

D

 

 

E

 

 

F

 

 

 

02953

 

 

electric

Fig. 35

BELT INSTALLATION -

•Install new belt from tractor rear to front, over the steer- ing plate (H) and above clutch brake pedal shaft (J).

•Pull belt toward front of tractor and roll belt around electric clutch and onto engine pulley (G).

•Pull belt toward rear of tractor. Carefully work belt down around transmission cooling fan and onto the input pulley (F). Be sure belt is inside the belt keeper.

•Install belt on centerspan idler (E).

•Install belt through stationary idler (C) and clutching idler (D).

•Reinstall anti-rotation link (B) on right side of tractor. Tighten securely.

•Reconnect clutch harness (A).

•Make sure belt is in all pulley grooves and inside all belt guides and keepers.

•Install mower (See “TO INSTALL MOWER” in this section of manual).

TO CHECK BRAKE

If tractor requires more than five (5) feet to stop at highest speed in highest gear on a level, dry concrete or paved surface, then brake must be serviced.

You may also check brake by:

•Park tractor on a level, dry concrete or paved surface, depress brake pedal all the way down and engage parking brake.

•Disengage transmission by placing freewheel control in “transmission disengaged” position. Pull freewheel control out and into the slot and release so it is held in the disengaged position.

The rear wheels must lock and skid when you try to manu- ally push the tractor forward. If the rear wheels rotate, then the brake needs to be serviced. Contact a qualified service center.

FRONT WHEEL TOE-IN/CAMBER

Your new tractor front wheel toe-in and camber is set at the factory and is normal. The front wheel toe-in and camber are not adjustable. If damage has occurred to affect the factory set front wheel toe-in or camber, contact a qualified service center.

23

Page 22 Page 24
Image 23
Page 22 Page 24
Contents YTH2348 II. Slope Operation Safety RulesSafe Operation Practices for Ride-On Mowers General OperationIV. Towing ServiceIII. Children Table of Contents To Remove Tractor from Carton AssemblyTools Required for Assembly Unassembled PartsCheck Brake System Check Tire PressureCheck Deck Levelness Check for Proper Position of ALL BeltsOperation Reverse Operation System ROS on Position Know Your TractorTo USE Throttle Control D See Fig HOW to USE Your TractorTo SET Parking Brake See Fig StoppingTo USE Cruise Control J See Fig To Adjust Mower Cutting Height See FigTo Adjust Gauge Wheels See Fig To Move Forward and Backward See FigTo Operate on Hills Service REMINDER/HOUR MeterUsing the Reverse Operation System Reverse Operation System ROS See FigTo Start Engine See Fig Before Starting the EngineCheck Engine OIL Level ADD GasolinePurge Transmission Mowing TipsLubrication Chart MaintenanceBrake Operation BatteryTractor Blade CareTransaxle Pump Fluid EngineBelts Transaxle CoolingCleaning To Remove Mower See Fig Service and AdjustmentsTo Install Mower See Figs First Install ANTI-SWAY BAR S LBF To Level Mower Mower Drive Belt Removal Mower Drive Belt InstallationTo Replace Mower Blade Drive Belt See Fig Front Wheel TOE-IN/CAMBER Belt InstallationTo Replace Motion Drive Belt See Fig To Check BrakeTo Attach Jumper Cables To Start Engine with a Weak BatteryReplacing Battery See Fig To Remove Wheel for Repairs See FigTo Replace Headlight Bulb To Adjust Throttle Control CableTo Adjust Choke Control To Adjust CarburetorEngine OIL StorageOther Fuel SystemTroubleshooting Points Engine dies when Tractor Model NO. YTH2348 96045001900, Product no 45 SchematicElectrical KEY Part Description Chassis Tractor Model NO. YTH2348 96045001900, Product no 45 197 196 DriveTractor Model NO. YTH2348 96045001900, Product no 45 1837 Spark Arrester KITEngine Engine Power Rating Information Steering Assembly 532 40 Seat Seat AssemblyMower Deck 532 40 Deck Weldment Mower Mower Lift Wheels and Tires DecalsService Notes Service Notes Service Notes Suggested Guide for Sighting Slopes for Safe Operation Warranty Statement

96045001900 specifications

The Husqvarna 96045001900 is a versatile and robust chainsaw designed to meet the demands of both professionals and enthusiasts in the field of forestry and landscaping. Its powerful engine and advanced features make it an ideal choice for various cutting tasks, whether for maintenance, tree felling, or pruning.

One of the standout features of this chainsaw is its high-performance engine. The Husqvarna 96045001900 is equipped with a reliable and efficient 50.2cc engine, which delivers exceptional power and speed. This engine not only provides the necessary torque for cutting through tough materials but also ensures that users can complete their tasks with minimal effort.

The chainsaw boasts a lightweight design, which enhances maneuverability without sacrificing durability. Weighing in at just about 11 lbs, it allows users to handle it with ease during extended periods of operation. The ergonomic handle contributes to this comfort, offering a secure grip that reduces fatigue, especially during larger jobs.

Another essential aspect of the Husqvarna 96045001900 is its advanced air filtration system. This feature helps in maintaining engine performance by keeping dust and debris out of the engine, thereby prolonging its lifespan and reducing maintenance needs. In addition, the chainsaw is designed with an automatic oiling system, ensuring that the chain is consistently lubricated for optimal performance.

The chainsaw also incorporates Husqvarna’s unique X-Torq technology, which reduces fuel consumption and minimizes exhaust emissions. This environmentally friendly innovation not only contributes to lower operating costs but also meets stringent emission regulations, making it suitable for use in eco-sensitive areas.

Safety features are paramount in the design of the Husqvarna 96045001900. It comes equipped with a chain brake that stops the chain immediately in case of kickback, ensuring user safety. Furthermore, the front hand guard and throttle lockout prevent accidental starts and provide additional protection while operating the saw.

In conclusion, the Husqvarna 96045001900 is a high-quality chainsaw that excels in power, efficiency, and safety. With its powerful engine, lightweight construction, advanced air filtration, and cutting-edge technologies, it stands out as a top choice for anyone looking to tackle tough cutting jobs with ease and confidence. Whether for professional forestry work or home landscaping projects, this chainsaw delivers performance and reliability that make it a worthy investment.
Top Page Image Contents