Husqvarna 96045001900 Before Starting the Engine, Check Engine OIL Level, ADD Gasoline

Page 12

OPERATION

BEFORE STARTING THE ENGINE

CHECK ENGINE OIL LEVEL

The engine in your tractor has been shipped, from the factory, already filled with summer weight oil.

•Check engine oil with tractor on level ground.

•Remove oil fill cap/dipstick and wipe clean, reinsert the dipstick and screw cap tight, wait for a few seconds, remove and read oil level. If necessary, add oil until “FULL” mark on dipstick is reached. Do not overfill.

•For cold weather operation you should change oil for easier starting (See “OIL VISCOSITY CHART” in the Maintenance section of this manual).

•To change engine oil, see the Maintenance section in this manual.

ADD GASOLINE

•Fill fuel tank to bottom of filler neck. Do not overfill. Use fresh, clean, regular unleaded gasoline with a minimum of 87 octane. (Use of leaded gasoline will increase carbon and lead oxide deposits and reduce valve life). Do not mix oil with gasoline. Purchase fuel in quantities that can be used within 30 days to assure fuel freshness.

CAUTION: Wipe off any spilled oil or fuel. Do not store, spill or use gasoline near an open flame.

IMPORTANT: WHEN OPERATING IN TEMPERATURES BELOW32°F(0°C), USE FRESH, CLEAN WINTER GRADE GASOLINE TO HELP ENSURE GOOD COLD WEATHER STARTING.

CAUTION: Alcohol blended fuels (called gasohol or using ethanol or methanol) can attract moisture which leads to separation and formation of acids during storage. Acidic gas can damage the fuel system of an engine while in storage. To avoid engine problems, the fuel system should be emptied before storage of 30 days or longer. Drain the gas tank, start the engine and let it run until the fuel lines and carburetor are empty. Use fresh fuel next season. See Storage Instructions for additional information. Never use engine or carburetor cleaner products in the fuel tank or permanent damage may occur.

TO START ENGINE (See Fig. 3)

When starting the engine for the first time or if the engine has run out of fuel, it will take extra cranking time to move fuel from the tank to the engine.

•Be sure freewheel control is in the transmission engaged position.

•Sit on seat in operating position, depress brake pedal and set parking brake.

•Move attachment clutch to “DISENGAGED” position.

•Move throttle control to fast position

•Pull choke control out for a cold engine start attempt. For a warm engine start attempt the choke control may not be needed.

NOTE: Before starting, read the warm and cold starting procedures below.

•Insert key into ignition and turn key clockwise to “START” position and release key as soon as engine starts. Do not run starter continuously for more than fifteen seconds per minute. If the engine does not start after several attempts, push choke control in, wait a few minutes and try again. If engine still does not start, pull the choke control out and retry.

WARM WEATHER STARTING (50° F and above)

•When engine starts, slowly push choke control in until the engine begins to run smoothly. If the engine starts to run roughly, pull the choke control out slightly for a few seconds and then continue to push the control in slowly.

•The attachments and ground drive can now be used. If the engine does not accept the load, restart the engine and allow it to warm up for one minute using the choke as described above.

COLD WEATHER STARTING (50° F and below)

•When engine starts, slowly push choke control in until the engine begins to run smoothly. Continue to push the choke control in small steps allowing the engine to accept small changes in speed and load, until the choke control is fully in. If the engine starts to run roughly, pull the choke control out slightly for a few seconds and then continue to push the control in slowly. This may require an engine warm-up period from several seconds to several minutes, depending on the temperature.

AUTOMATIC TRANSMISSION WARM UP

•Before driving the unit in cold weather, the transmission should be warmed up as follows:

•Be sure the tractor is on level ground.

•Release the parking brake and let the brake slowly return to operating position.

•Allow one minute for transmission to warm up. This can be done during the engine warm up period.

•The attachments can be used during the engine warm-up period after the transmission has been warmed up and may require the choke control be pulled out slightly.

NOTE: If at a high altitude (above 3000 feet) or in cold temperatures (below 32 F) the carburetor fuel mixture may need to be adjusted for best engine performance. See “TO ADJUST CARBURETOR” in the Service and Adjustments section of this manual.

12

Page 11 Page 13
Image 12
Page 11 Page 13
Contents YTH2348 Safety Rules Safe Operation Practices for Ride-On MowersGeneral Operation II. Slope OperationService III. ChildrenIV. Towing Table of Contents Assembly Tools Required for AssemblyUnassembled Parts To Remove Tractor from CartonCheck Tire Pressure Check Deck LevelnessCheck for Proper Position of ALL Belts Check Brake SystemOperation Know Your Tractor Reverse Operation System ROS on PositionHOW to USE Your Tractor To SET Parking Brake See FigStopping To USE Throttle Control D See FigTo Adjust Mower Cutting Height See Fig To Adjust Gauge Wheels See FigTo Move Forward and Backward See Fig To USE Cruise Control J See FigService REMINDER/HOUR Meter Using the Reverse Operation SystemReverse Operation System ROS See Fig To Operate on HillsBefore Starting the Engine Check Engine OIL LevelADD Gasoline To Start Engine See FigMowing Tips Purge TransmissionMaintenance Lubrication ChartBattery TractorBlade Care Brake OperationEngine BeltsTransaxle Cooling Transaxle Pump FluidCleaning Service and Adjustments To Install Mower See FigsTo Remove Mower See Fig First Install ANTI-SWAY BAR S LBF To Level Mower Mower Drive Belt Installation To Replace Mower Blade Drive Belt See FigMower Drive Belt Removal Belt Installation To Replace Motion Drive Belt See FigTo Check Brake Front Wheel TOE-IN/CAMBERTo Start Engine with a Weak Battery Replacing Battery See FigTo Remove Wheel for Repairs See Fig To Attach Jumper CablesTo Adjust Throttle Control Cable To Adjust Choke ControlTo Adjust Carburetor To Replace Headlight BulbStorage OtherFuel System Engine OILTroubleshooting Points Engine dies when Schematic Tractor Model NO. YTH2348 96045001900, Product no 45Electrical KEY Part Description Chassis Tractor Model NO. YTH2348 96045001900, Product no 45 Drive 197 196Tractor Model NO. YTH2348 96045001900, Product no 45 Spark Arrester KIT Engine1837 Engine Power Rating Information Steering Assembly Seat Assembly 532 40 SeatMower Deck 532 40 Deck Weldment Mower Mower Lift Decals Wheels and TiresService Notes Service Notes Service Notes Suggested Guide for Sighting Slopes for Safe Operation Warranty Statement

96045001900 specifications

The Husqvarna 96045001900 is a versatile and robust chainsaw designed to meet the demands of both professionals and enthusiasts in the field of forestry and landscaping. Its powerful engine and advanced features make it an ideal choice for various cutting tasks, whether for maintenance, tree felling, or pruning.

One of the standout features of this chainsaw is its high-performance engine. The Husqvarna 96045001900 is equipped with a reliable and efficient 50.2cc engine, which delivers exceptional power and speed. This engine not only provides the necessary torque for cutting through tough materials but also ensures that users can complete their tasks with minimal effort.

The chainsaw boasts a lightweight design, which enhances maneuverability without sacrificing durability. Weighing in at just about 11 lbs, it allows users to handle it with ease during extended periods of operation. The ergonomic handle contributes to this comfort, offering a secure grip that reduces fatigue, especially during larger jobs.

Another essential aspect of the Husqvarna 96045001900 is its advanced air filtration system. This feature helps in maintaining engine performance by keeping dust and debris out of the engine, thereby prolonging its lifespan and reducing maintenance needs. In addition, the chainsaw is designed with an automatic oiling system, ensuring that the chain is consistently lubricated for optimal performance.

The chainsaw also incorporates Husqvarna’s unique X-Torq technology, which reduces fuel consumption and minimizes exhaust emissions. This environmentally friendly innovation not only contributes to lower operating costs but also meets stringent emission regulations, making it suitable for use in eco-sensitive areas.

Safety features are paramount in the design of the Husqvarna 96045001900. It comes equipped with a chain brake that stops the chain immediately in case of kickback, ensuring user safety. Furthermore, the front hand guard and throttle lockout prevent accidental starts and provide additional protection while operating the saw.

In conclusion, the Husqvarna 96045001900 is a high-quality chainsaw that excels in power, efficiency, and safety. With its powerful engine, lightweight construction, advanced air filtration, and cutting-edge technologies, it stands out as a top choice for anyone looking to tackle tough cutting jobs with ease and confidence. Whether for professional forestry work or home landscaping projects, this chainsaw delivers performance and reliability that make it a worthy investment.
Top Page Image Contents