Husqvarna 96045001502, 532 43 00-01 Transaxle Motion Control Lever Neutral Adjustment See Fig

Page 24

SERVICE AND ADJUSTMENTS

TRANSAXLE MOTION CONTROL LEVER NEUTRAL ADJUSTMENT (See Fig. 40)

The motion control lever has been preset at the factory and adjustment should not be necessary.

•Loosen adjustment bolt in front of the right rear wheel, and lightly tighten.

•Start engine and move motion control lever until tractor does not move forward or backward.

•Hold motion control lever in that position and turn engine off.

•While holding motion control lever in place, loosen the adjustment bolt.

•Move motion control lever to the neutral (lock gate) position.

•Tighten adjustment bolt securely.

NOTE: If additional clearance is needed to get to adjustment bolt, move mower deck height to the lowest position.

After above adjustment is made, if the tractor still creeps forward or backward while motion control lever is in neutral position, follow these steps:

•Loosen the adjustment bolt.

•Move the motion control lever 1/4 to 1/2 inch in the direction it is trying to creep.

•Tighten adjustment bolt securely.

•Start engine and test.

•If tractor still creeps, repeat above steps until satisfied.

MOTION CONTROL

NEUTRAL

LEVER

LOCK

 

GATE

 

ADJUSTMENT

 

BOLT

FIG. 40

TO START ENGINE WITH A WEAK BATTERY (See Fig. 41)

WARNING: Lead-acid batteries gen- erate explosive gases. Keep sparks, flame and smoking materials away from batteries. Always wear eye protection when around batteries.

If your battery is too weak to start the engine, it should be recharged. (See "BATTERY" in the MAINTENANCE sec- tion of this manual).

If “jumper cables” are used for emergency starting, follow this procedure:

IMPORTANT: YOUR TRACTOR IS EQUIPPED WITH A 12 VOLT SYSTEM. THE OTHER VEHICLE MUST ALSO BE A 12 VOLT SYSTEM. DO NOT USE YOUR TRACTOR BATTERY TO START OTHER VEHICLES.

TO ATTACH JUMPER CABLES -

•Connect one end of the RED cable to the POSITIVE

(+)terminal of each battery(A-B), taking care not to short against tractor chassis.

•Connect one end of the BLACK cable to the NEGATIVE (-) terminal (C) of fully charged battery.

•Connect the other end of the BLACK cable (D) to good chassis ground, away from fuel tank and battery.

TO REMOVE CABLES, REVERSE ORDER -

•BLACK cable first from chassis and then from the fully charged battery.

•RED cable last from both batteries.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

WEAK OR DEAD

 

 

 

 

 

 

 

FULLY CHARGED

BATTERY

 

 

 

 

 

 

 

BATTERY

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Fig. 41

24

Page 23 Page 25
Image 24
Page 23 Page 25
Contents LGT2554 Safety Rules Safe Operation Practices for Ride-On MowersGeneral Operation II. Slope OperationService General ServiceIII. Children IV. TowingTable of Contents Assembly Tools Required for AssemblyUnassembled Parts ToremovetractorfromcartonTo Adjust Seat See Fig To Install Mower and Drive Belt See FigsSET Parking Brake Lever and Lower AT- Tachment Lift See Fig Assemble Front Gauge Wheel W to Front of Mower See FigInstall ANTI-SWAY BAR S if Equipped See Slide Mower Under Tractor See FigANTI-SWAY BAR S Attach Mower Side Suspension Arms a to Chassis See Fig Attach Rear Lift Links C See FigAttach Front Link E See Fig Install Belt on Engine Clutch Pulley M See Check Tire PressureCheck Deck Levelness CheckforproperpositionofallbeltsOperation Know Your Tractor DPH AC JHOW to USE Your Tractor To SET Parking BRAKESee FigStopping See Fig To USE Throttle Control See FigTo Adjust Gauge Wheels See Fig To Adjust Mower Cutting Height See FigTo Move Forward and Backward See Fig To Operate MowerService REMINDER/HOUR Meter Reverse Operation System ROS See FigTo Operate on Hills To Transport SeeBefore Starting the Engine Check Engine OIL LevelADD Gasoline To Start Engine See FigMowing Tips Purge TransmissionMaintenance MaintenanceGeneral Recommendations ScheduleBattery TractorBlade Care Blade Removal See FigEngine Cleaning IN-LINE Fuel Filter See FigDeck Washout Port See Fig Service and Adjustments To Install MowerTo Remove Mower See Fig To Replace Mower Blade Drive Belt See FigTo Level Mower To Replace Motion Drive Belt See Fig To Check BrakeFront Wheel TOE-IN/CAMBER To Remove Wheel See FigTransaxle Motion Control Lever Neutral Adjustment See Fig To Start Engine with a Weak Battery See FigTo Attach Jumper Cables To Remove CABLES, Reverse OrderTransmission Storage OtherFuel System Engine OILProblem Cause Correction To run when oper Battery will notFires when turn Engine continuesDecals Wheels and TiresKEY Part Description Schematic SCH12Electrical KEY Part Description Chassis 532 40 873 90Drive 874 49 532 42Engine 30!2+ª!22%34%2ª+4Seat Assembly 532 42 SeatSteering Assembly 532 41 Wheel, Steering 532 19 Mower Deck 532 40 31-25 Deck Weldment Mower Mower Lift Suggested Guide for Sighting Slopes for Safe Operation Only Ride UP and Down Hill Not Across Hill Degrees MAXLimitations and Exclusions HOW to Obtain Service Consumer Wheeled Warranty Chart 06.21.10 JA

532 43 00-01, 96045001502 specifications

The Husqvarna 96045001502,532 43 00-01 is an advanced lawn mower designed for homeowners seeking efficiency, durability, and exceptional cutting performance. This model stands out for its robust features and innovative technologies that make lawn maintenance a breeze.

One of the key features of the Husqvarna 96045001502 is its powerful engine. Equipped with a reliable and efficient gasoline engine, it delivers optimal performance and allows the mower to tackle various terrain types effortlessly. The engine is designed to provide consistent power, ensuring that the mower can handle thick grass and tough conditions without compromising on its cutting capability.

The cutting deck is another highlight of this model. The Husqvarna lawn mower boasts a wide cutting deck that ensures a clean and even cut across the lawn. This feature minimizes the number of passes needed to achieve a well-manicured appearance, saving valuable time while enhancing lawn aesthetics. Furthermore, the deck's design promotes efficient grass discharge, ensuring that clippings are evenly distributed across the lawn or can be easily collected for mulching purposes.

In terms of ergonomics, the Husqvarna 96045001502 is designed with user comfort in mind. The adjustable handlebar system allows users of different heights to find a comfortable grip, reducing fatigue during prolonged use. Additionally, the mower is lightweight yet sturdy, making it easy to maneuver around obstacles and navigate through tight spaces in the yard.

Safety is also a priority with this mower. It comes equipped with features such as automatic blade stop technology, which ensures the blades come to a halt instantly when the user releases the handle. This mechanism reduces the risk of accidents, making it a safe choice for families and inexperienced users alike.

The Husqvarna 96045001502,532 43 00-01 incorporates several innovative technologies that enhance its performance. The Air Injection system, for example, helps to keep the air filter clean longer by separating large debris from the airflow. This extends the life of the engine and maintains performance over time.

In summary, the Husqvarna 96045001502,532 43 00-01 is an exceptional lawn mower that combines power, efficiency, and user-friendly features. With its durable construction, ergonomic design, and advanced technologies, it stands out as a top choice for homeowners looking to maintain a beautiful, healthy lawn with ease.
Top Page Image Contents