Husqvarna 532 43 00-01 Service and Adjustments, To Remove Mower See Fig, To Install Mower

Page 21

SERVICE AND ADJUSTMENTS

WARNING: TO AVOID SERIOUS INJURY, BEFORE PERFORMING ANY SERVICE OR ADJUSTMENTS:

•Depress brake pedal fully and set parking brake.

•Place motion control lever in neutral position.

•Place attachment clutch in “DISENGAGED” position.

•Turn ignition key to “STOP” and remove key.

•Make sure the blades and all moving parts have completely stopped.

•Disconnect spark plug wire from spark plug and place wire where it cannot come in contact with plug.

TO REMOVE MOWER (See Fig. 32)

•Place attachment clutch in “DISENGAGED” position.

•Lower attachment lift lever to its lowest position.

•Disengage belt tension rod (K) from lock bracket (L).

CAUTION: Belt tension rod is spring loaded. Have a tight grip on rod and release slowly.

•Remove mower belt from electric clutch pulley (M).

•Disconnect front link (E) from mower - remove retainer spring and washer.

•Gotoeithersideofmoweranddisconnectmowersuspen- sion arm (A) from chassis and rear lift link (C) from rear mowerbracket(D)-removeretainerspringsandwashers.

•Go to other side of mower and disconnect the suspen- sion arm and rear lift link.

CAUTION: After rear lift links are discon- nected, the attachment lift lever will be spring loaded. Have a tight grip on lift lever when changing position of the lever.

•From right side of mower, disconnect anti-sway bar (S) from right rear mower bracket (D) - remove retainer spring and washer and pull mower toward you until the bar falls from the hole in bracket.

•Turn tractor steering wheel to the left as far as it will go.

•Slide mower out from under right side of tractor.

TO INSTALL MOWER

Follow procedure described in “INSTALL MOWER AND DRIVE BELT” in the Assembly section of this manual.

TO REPLACE MOWER BLADE DRIVE BELT (See Fig. 33)

MOWER DRIVE BELT REMOVAL

•Park tractor on a level surface. Engage parking brake.

•Lower attachment lift lever to its lowest position.

•Disengage belt tension rod (K) from lock bracket (L).

CAUTION: Belt tension rod is spring loaded. Have a firm grip on rod and release slowly.

•Remove screws (P) from mandrel covers (Q) and remove covers.

•Removeanydirtorgrassclippingswhichmayhaveaccu- mulated around mandrels and entire upper deck surface.

•Remove belt from electric clutch pulley (M), both man- drel pulleys (R) and all idler pulleys (V).

MOWER DRIVE BELT INSTALLATION

•Install belt around all mandrel pulleys (R) and around idler pulleys (V) as shown.

•Install belt onto electric clutch pulley (M).

IMPORTANT: Check belt for proper routing in all mower pulley grooves.

•Reassemble mandrel covers (Q). Securely tighten all screws.

•Engage belt tension rod (K) on locking bracket (L).

CAUTION: Belt tension rod is spring loaded. Have a firm grip on rod and release slowly.

•Raise attachment lift lever to highest position.

 

L

 

 

B

M

 

 

 

 

 

 

F

 

 

 

 

 

 

 

 

 

 

 

 

E

K

 

 

 

A

 

 

 

 

 

 

 

H

 

 

 

 

 

 

C

D

S

 

 

 

 

 

C

D

 

 

 

 

 

 

 

 

 

 

 

Fig. 32

 

21

 

 

 

 

 

 

P

P

 

 

 

L

M

P

 

Q

 

K

R

Q

R

V

 

 

R

 

Fig. 33

Page 20 Page 22
Image 21
Page 20 Page 22
Contents LGT2554 Safe Operation Practices for Ride-On Mowers Safety RulesGeneral Operation II. Slope OperationGeneral Service ServiceIII. Children IV. TowingTable of Contents Tools Required for Assembly AssemblyUnassembled Parts ToremovetractorfromcartonTo Install Mower and Drive Belt See Figs To Adjust Seat See FigSET Parking Brake Lever and Lower AT- Tachment Lift See Fig Assemble Front Gauge Wheel W to Front of Mower See FigInstall ANTI-SWAY BAR S if Equipped See Slide Mower Under Tractor See FigANTI-SWAY BAR S Attach Mower Side Suspension Arms a to Chassis See Fig Attach Rear Lift Links C See FigAttach Front Link E See Fig Check Tire Pressure Install Belt on Engine Clutch Pulley M SeeCheck Deck Levelness CheckforproperpositionofallbeltsOperation DPH AC J Know Your TractorTo SET Parking BRAKESee Fig HOW to USE Your TractorStopping See Fig To USE Throttle Control See FigTo Adjust Mower Cutting Height See Fig To Adjust Gauge Wheels See FigTo Move Forward and Backward See Fig To Operate MowerReverse Operation System ROS See Fig Service REMINDER/HOUR MeterTo Operate on Hills To Transport SeeCheck Engine OIL Level Before Starting the EngineADD Gasoline To Start Engine See FigPurge Transmission Mowing TipsMaintenance MaintenanceGeneral Recommendations ScheduleTractor BatteryBlade Care Blade Removal See FigEngine Cleaning IN-LINE Fuel Filter See FigDeck Washout Port See Fig To Install Mower Service and AdjustmentsTo Remove Mower See Fig To Replace Mower Blade Drive Belt See FigTo Level Mower To Check Brake To Replace Motion Drive Belt See FigFront Wheel TOE-IN/CAMBER To Remove Wheel See FigTo Start Engine with a Weak Battery See Fig Transaxle Motion Control Lever Neutral Adjustment See FigTo Attach Jumper Cables To Remove CABLES, Reverse OrderTransmission Other StorageFuel System Engine OILProblem Cause Correction Battery will not To run when operFires when turn Engine continuesDecals Wheels and TiresKEY Part Description SCH12 SchematicElectrical KEY Part Description Chassis 873 90 532 40Drive 532 42 874 4930!2+ª!22%34%2ª+4 Engine532 42 Seat Seat AssemblySteering Assembly 532 41 Wheel, Steering 532 19 Mower Deck 532 40 31-25 Deck Weldment Mower Mower Lift Only Ride UP and Down Hill Not Across Hill Degrees MAX Suggested Guide for Sighting Slopes for Safe OperationLimitations and Exclusions HOW to Obtain Service Consumer Wheeled Warranty Chart 06.21.10 JA

532 43 00-01, 96045001502 specifications

The Husqvarna 96045001502,532 43 00-01 is an advanced lawn mower designed for homeowners seeking efficiency, durability, and exceptional cutting performance. This model stands out for its robust features and innovative technologies that make lawn maintenance a breeze.

One of the key features of the Husqvarna 96045001502 is its powerful engine. Equipped with a reliable and efficient gasoline engine, it delivers optimal performance and allows the mower to tackle various terrain types effortlessly. The engine is designed to provide consistent power, ensuring that the mower can handle thick grass and tough conditions without compromising on its cutting capability.

The cutting deck is another highlight of this model. The Husqvarna lawn mower boasts a wide cutting deck that ensures a clean and even cut across the lawn. This feature minimizes the number of passes needed to achieve a well-manicured appearance, saving valuable time while enhancing lawn aesthetics. Furthermore, the deck's design promotes efficient grass discharge, ensuring that clippings are evenly distributed across the lawn or can be easily collected for mulching purposes.

In terms of ergonomics, the Husqvarna 96045001502 is designed with user comfort in mind. The adjustable handlebar system allows users of different heights to find a comfortable grip, reducing fatigue during prolonged use. Additionally, the mower is lightweight yet sturdy, making it easy to maneuver around obstacles and navigate through tight spaces in the yard.

Safety is also a priority with this mower. It comes equipped with features such as automatic blade stop technology, which ensures the blades come to a halt instantly when the user releases the handle. This mechanism reduces the risk of accidents, making it a safe choice for families and inexperienced users alike.

The Husqvarna 96045001502,532 43 00-01 incorporates several innovative technologies that enhance its performance. The Air Injection system, for example, helps to keep the air filter clean longer by separating large debris from the airflow. This extends the life of the engine and maintains performance over time.

In summary, the Husqvarna 96045001502,532 43 00-01 is an exceptional lawn mower that combines power, efficiency, and user-friendly features. With its durable construction, ergonomic design, and advanced technologies, it stands out as a top choice for homeowners looking to maintain a beautiful, healthy lawn with ease.
Top Page Image Contents