Husqvarna 532 43 00-01 To Move Forward and Backward See Fig, To Adjust Gauge Wheels See Fig

Page 13

OPERATION

TO MOVE FORWARD AND BACKWARD (See Fig. 19)

The direction and speed of movement is controlled by the motion control lever. (J)

J

Fig. 19

•Start tractor with motion control lever in neutral position.

•Release parking brake.

•Slowly move motion control lever to desired position.

TO ADJUST GAUGE WHEELS (See Fig. 21)

Gauge wheels are properly adjusted when they are slightly off the ground when mower is at the desired cutting height in operating position. Gauge wheels then keep the deck in prop- er position to help prevent scalping in most terrain conditions.

NOTE: Adjust gauge wheels with tractor on a flat level surface.

•Adjustmowertodesiredcuttingheight(See“TOADJUST MOWER CUTTING HEIGHT” in this section of manual).

•With mower in desired height of cut position, gauge wheels should be assembled so they are slightly off the ground. Install gauge wheel in appropriate hole. Tighten securely.

•Repeat for all, installing gauge wheel in same adjust- ment hole.

TO ADJUST MOWER CUTTING HEIGHT (See Fig. 20)

The position of the attachment lift lever (A) determines the cutting height.

A

Fig. 20

•Put attachment lift lever in desired cutting height slot.

The cutting height range is approximately 1" to 4". The heights are measured from the ground to the blade tip with the engine not running. These heights are approximate and may vary depending upon soil conditions, height of grass and types of grass being mowed.

•The average lawn should be cut to approximately 2-1/2" during the cool season and to over 3" during hot months. For healthier and better looking lawns, mow often and after moderate growth.

•For best cutting performance, grass over 6 inches in height should be mowed twice. Make the first cut relatively high; the second to desired height.

13

Fig. 21

TO OPERATE MOWER

Your tractor is equipped with an operator presence sensing switch. Any attempt by the operator to leave the seat with the engine running and the attachment clutch engaged will shut off the engine. You must remain fully and centrally positioned in the seat to prevent the engine from hesitat- ing or cutting off when operating your equipment on rough, rolling terrain or hills.

•Select desired height of cut with attachment lift lever.

•Start mower blades by engaging attachment clutch control.

TO STOP MOWER BLADES

•Disengage attachment clutch control.

CAUTION: Do not operate the mower without either the entire grass catcher, on mowers so equipped, or the deflector shield (S) in place (See Fig. 22).

S

Fig. 22

Page 12 Page 14
Image 13
Page 12 Page 14
Contents LGT2554 Safe Operation Practices for Ride-On Mowers Safety RulesGeneral Operation II. Slope OperationGeneral Service ServiceIII. Children IV. TowingTable of Contents Tools Required for Assembly AssemblyUnassembled Parts ToremovetractorfromcartonTo Install Mower and Drive Belt See Figs To Adjust Seat See FigSET Parking Brake Lever and Lower AT- Tachment Lift See Fig Assemble Front Gauge Wheel W to Front of Mower See FigSlide Mower Under Tractor See Fig Install ANTI-SWAY BAR S if Equipped SeeANTI-SWAY BAR S Attach Rear Lift Links C See Fig Attach Mower Side Suspension Arms a to Chassis See FigAttach Front Link E See Fig Check Tire Pressure Install Belt on Engine Clutch Pulley M SeeCheck Deck Levelness CheckforproperpositionofallbeltsOperation DPH AC J Know Your TractorTo SET Parking BRAKESee Fig HOW to USE Your TractorStopping See Fig To USE Throttle Control See FigTo Adjust Mower Cutting Height See Fig To Adjust Gauge Wheels See FigTo Move Forward and Backward See Fig To Operate MowerReverse Operation System ROS See Fig Service REMINDER/HOUR MeterTo Operate on Hills To Transport SeeCheck Engine OIL Level Before Starting the EngineADD Gasoline To Start Engine See FigPurge Transmission Mowing TipsMaintenance MaintenanceGeneral Recommendations ScheduleTractor BatteryBlade Care Blade Removal See FigEngine IN-LINE Fuel Filter See Fig CleaningDeck Washout Port See Fig To Install Mower Service and AdjustmentsTo Remove Mower See Fig To Replace Mower Blade Drive Belt See FigTo Level Mower To Check Brake To Replace Motion Drive Belt See FigFront Wheel TOE-IN/CAMBER To Remove Wheel See FigTo Start Engine with a Weak Battery See Fig Transaxle Motion Control Lever Neutral Adjustment See FigTo Attach Jumper Cables To Remove CABLES, Reverse OrderTransmission Other StorageFuel System Engine OILProblem Cause Correction Battery will not To run when operFires when turn Engine continuesWheels and Tires DecalsKEY Part Description SCH12 SchematicElectrical KEY Part Description Chassis 873 90 532 40Drive 532 42 874 4930!2+ª!22%34%2ª+4 Engine532 42 Seat Seat AssemblySteering Assembly 532 41 Wheel, Steering 532 19 Mower Deck 532 40 31-25 Deck Weldment Mower Mower Lift Only Ride UP and Down Hill Not Across Hill Degrees MAX Suggested Guide for Sighting Slopes for Safe OperationLimitations and Exclusions HOW to Obtain Service Consumer Wheeled Warranty Chart 06.21.10 JA

532 43 00-01, 96045001502 specifications

The Husqvarna 96045001502,532 43 00-01 is an advanced lawn mower designed for homeowners seeking efficiency, durability, and exceptional cutting performance. This model stands out for its robust features and innovative technologies that make lawn maintenance a breeze.

One of the key features of the Husqvarna 96045001502 is its powerful engine. Equipped with a reliable and efficient gasoline engine, it delivers optimal performance and allows the mower to tackle various terrain types effortlessly. The engine is designed to provide consistent power, ensuring that the mower can handle thick grass and tough conditions without compromising on its cutting capability.

The cutting deck is another highlight of this model. The Husqvarna lawn mower boasts a wide cutting deck that ensures a clean and even cut across the lawn. This feature minimizes the number of passes needed to achieve a well-manicured appearance, saving valuable time while enhancing lawn aesthetics. Furthermore, the deck's design promotes efficient grass discharge, ensuring that clippings are evenly distributed across the lawn or can be easily collected for mulching purposes.

In terms of ergonomics, the Husqvarna 96045001502 is designed with user comfort in mind. The adjustable handlebar system allows users of different heights to find a comfortable grip, reducing fatigue during prolonged use. Additionally, the mower is lightweight yet sturdy, making it easy to maneuver around obstacles and navigate through tight spaces in the yard.

Safety is also a priority with this mower. It comes equipped with features such as automatic blade stop technology, which ensures the blades come to a halt instantly when the user releases the handle. This mechanism reduces the risk of accidents, making it a safe choice for families and inexperienced users alike.

The Husqvarna 96045001502,532 43 00-01 incorporates several innovative technologies that enhance its performance. The Air Injection system, for example, helps to keep the air filter clean longer by separating large debris from the airflow. This extends the life of the engine and maintains performance over time.

In summary, the Husqvarna 96045001502,532 43 00-01 is an exceptional lawn mower that combines power, efficiency, and user-friendly features. With its durable construction, ergonomic design, and advanced technologies, it stands out as a top choice for homeowners looking to maintain a beautiful, healthy lawn with ease.
Top Page Image Contents