Marantz M-CR603 manual Setting the others Other, Auto standby, Firmware update, Screen saver

Page 36

ENGLISH

Symbols used to indicate buttons in this guide

Button located on both the main unit and the remote control

BUTTON

Button only on the main unit <BUTTON>

Button only on the remote control [BUTTON]

u/i <ENTER>

p

Setting the others [Other]

Auto standby

With the Auto standby ON, this unit will automatically enter the standby mode after about 30 continuous minutes of stop mode with no operation.

• The default setting is “OFF”.

1 Press [MENU].

Turns on the Menu settings mode and the Menu appears on the display. (vpage 26 “Menu map”)

2Use ui to select “Other”-“Auto Standby”, then press [ENTER/MEMO], <ENTER> or p.

3Use ui to select “On”, then press [ENTER/MEMO],

<ENTER> or p.

The setting is entered.

NOTE

In the following situations, the Auto standby function does not operate.

During CD playback or pause.

When an iPod or USB memory device is connected to the USB port on the unit.

When the input source is “TUNER”, “AUX2” or “AUX3”.

When the input source is “AUX1” and a devices connected to the AUX1 jack.

When the input source is “M-XPort” and an RX101 wireless receiver is connected to M-XPort.

When the input source is “AUX4” and a signal is input.

When the input source is “INTERNET RADIO”, “MUSIC SERVER” or “ONLINE MUSIC”, and a ethernet cable is connected to NETWORK connector.

Firmware update

• In order to use these functions, you must have the correct system requirements and settings for a broadband Internet connection (vpage 8).

• Perform the firmware update operation after at least 2 minutes has elapsed since turning this unit’s power ON.

1 Press [MENU].

Turns on the Menu settings mode and the Menu appears on the display. (vpage 26 “Menu map”)

2Use ui to select “Other”-“Firmware Update”, then press [ENTER/MEMO], <ENTER> or p.

[Selectable items]

Check for Update : Check for firmware updates. You can also check approximately how long it will take to complete an update.

Start : Execute the update process.

If updating fails, the set automatically retries, but if updating is still not possible, one of the messages shown below is displayed. If the display reads as shown below, check the settings and network environment, then update again.

Display

Description

Updating fail

Updating failed.

Login failed

Failure to log into server.

Server is busy

Server is busy. Wait a while then try again.

Connection fail

Failure in connecting to server.

Download fail

Downloading of the firmware has failed.

[MENU]

u [ENTER/MEMO]

p

i

Screen saver

Use the following procedure to set the screen saver.

1 Press [MENU].

Turns on the Menu settings mode and the Menu appears on the display. (vpage 26 “Menu map”)

Add New Feature

In order to use these functions, you must have the correct system requirements and settings for a broadband Internet connection (vpage 8).

Perform the add new feature operation after at least 2 minutes has elapsed since turning this unit’s power ON.

2Use ui to select “Other”-“Screen Saver”, then press [ENTER/MEMO], <ENTER> or p.

“Screen Saver”menu appears.

3Use ui to select “ON” , then press [ENTER/ MEMO], <ENTER> or p.

1 Press [MENU].

Turns on the Menu settings mode and the Menu appears on the display. (vpage 26 “Menu map”)

2Use ui to select “Other”-“Add new Feature”, then press [ENTER/MEMO], <ENTER> or p.

32

Image 36
Contents CR603 Page Compliance Information Important Notice do not Modify this ProductFor Canadian customers Avertissements Advertencias Contents Accessories Main featuresGetting started About this guideCleaning discs DiscsDiscs playable on this unit Loading discsAbout the remote control Operating range of the remote controlInserting the batteries Connecting the speaker cables This section explains how to connect speakers, recordingConnections Equipment, antennas and networkConnecting a TV CD recorder / MD recorderProtection circuit Cables used for connectionsConnecting an antenna NAM loop antenna assemblyNUsing the AM loop antenna Suspending on a wall Standing aloneConnecting an iPod Required systemNBroadband internet connection Modem RouterNSetting up the iPod stand NSetting your iPod on the iPod standIPod stand NIf the iPod stand becomes detachedConnecting a portable player Connecting the power cord USBMemory Device Portable AudioTurning the power on Setting the current time Auto Adjust 12-Hour DisplayTurning the power off Basic operationsInput source switching Adjusting the toneAdjusting the master volume Muting the soundCD playback Switching the display MP3 and WMA files playbackPlaying tracks in the desired order Program playback MP3 and WMA files playbackNTo switch the folder or file during playback Folder NSwitching the displayNSetting random playback FileTuning in Broadcast Stations Automatically presetting FM stations Auto presetTuner playback Presetting FM/AM stations manually Listening to preset stationsCalling stations reqistered in Preset List Deleting stations registered in Preset ListDisconnecting the iPod IPod playbackBefore playing a USB or an iPod Playing an iPodUSB memory device playback Playing files stored on USB memory devicesNUSB operation During playback, press DisplayNetwork audio playback Listening to internet radioNRecently played internet radio stations NRegistering internet radio stations as your favoritesListening to Napster NInternet radio operationNPlaying files that have been registered in your favorites NMusic server operationListening to Pandora NRegistering tracks in my Napster libraryNNapster operation Press ENTER/MEMO, Enter or pListening to Rhapsody Listening to tracks registered in my library NTrack menuSearch from the similar music Registering tracks in my libraryFavorite function Listening to AUXPlaying portable audio player Press FavoriteAdvanced operations Menu mapRemote control connection Setting the remote controlPress Input and op to select to , or press RX101Setting the timer Timer Setting the timerNSetting the timer to on or off NTo change the setting while setting the timerAdjusting the clock automatically Clock Setting the Time ZoneSetting the Summer Time Auto AdjustSetting the network Network Network connectingNetwork connecting DHCP=Off Proxy Settings Network Standby Update NotificationUpgrade Notification Friendly Name EditSetting the others Other Firmware updateAdd New Feature Auto standbySetting speaker output NListening to music using BI-AMPConnecting the speaker cables What is Bi-Amp?Setting AMP characteristics Adjusting the audio level balance between speakers a and BDB, 0 dB, +6 dB ResponseAuto power on Resetting the microprocessorOther functions Inputting charactersInformation Part names and functionsFront panel Rear panel Remote control E rNButtons that work with CDs NButtons that work with the tunerWReverse-skip/Forward-skip buttons EFast-reverse/Fast-forward buttonsNButtons that work with iPods or USBs NButtons that work with NetworkQReverse-skip/Forward-skip buttons YENTER/Memory buttonMP3 and WMA IPodUSB memory MP3 and WMA formatsNetwork audio NAbout the internet radio functionNMusic server NAbout Napster NAbout PandoraExplanation terms A2DPDlna FlacTroubleshooting Symptom Cause CountermeasureGInternet radio/Music server/iPod/USB/memory deviceH Specifications GRhapsodyHIndex Dimensions / Dimensions / Dimensioni