Husqvarna 96045002101 To Move Forward and Backward See Fig, To USE Cruise Control J See Fig

Page 10

OPERATION

TO MOVE FORWARD AND BACKWARD (See Fig. 7)

The direction and speed of movement is controlled by the forward and reverse drive pedals.

•Start tractor and release parking brake.

•Slowly depress forward (K) or reverse (L) drive pedal to begin movement. Ground speed increases the further down the pedal is depressed.

TO USE CRUISE CONTROL (J) (See Fig. 7)

The cruise control feature can be used for forward travel only.

J

K

L

FIG. 7

SYSTEM CHARACTERISTICS

The cruise control should only be used while mowing or transporting on relatively smooth, straight surfaces. Other conditions such as trimming at slow speeds may cause the cruise control to disengage. Do not use the cruise control on slopes, rough terrian or while trimmimg or turning.

•With forward drive pedal depressed to desired speed, pull cruise control lever (J) up and hold while lifting your foot off the pedal, then release the lever.

To disengage the cruise control, depress the brake pedal or tap on forward drive pedal.

TO ADJUST MOWER CUTTING HEIGHT (See Fig. 8)

The position of the attachment lift lever (A) determines the cutting height.

A

FIG. 8

•Put attachment lift lever in desired cutting height slot.

The cutting height range is approximately 1" to 4". The heights are measured from the ground to the blade tip with the engine not running. These heights are approximate and may vary depending upon soil conditions, height of grass and types of grass being mowed.

•The average lawn should be cut to approximately 2-1/2 inches during the cool season and to over 3 inches during hot months. For healthier and better looking lawns, mow often and after moderate growth.

•For best cutting performance, grass over 6 inches in height should be mowed twice. Make the first cut relatively high; the second to desired height.

TO ADJUST GAUGE WHEELS (See Fig. 9)

Gauge wheels are properly adjusted when they are slightly off the ground when mower is at the desired cutting height in operating position. Gauge wheels then keep the deck in prop- er position to help prevent scalping in most terrain conditions.

NOTE: Adjust gauge wheels with tractor on a flat level surface.

•Adjustmowertodesiredcuttingheight(See“TOADJUST MOWER CUTTING HEIGHT” in this section of manual).

•Withmowerindesiredheightofcutposition,gaugewheels should be assembled so they are slightly off the ground. Install gauge wheel in appropriate hole. Tighten securely.

•Repeat for all, installing gauge wheel in same adjust- ment hole.

FIG. 9

TO OPERATE MOWER (See Fig. 10)

Your tractor is equipped with an operator presence sensing switch. Any attempt by the operator to leave the seat with the engine running and the attachment clutch engaged will shut off the engine. You must remain fully and centrally positioned in the seat to prevent the engine from hesitating or cutting off when operating your equipment on rough, rolling terrain or hills.

1.Select desired height of cut with attachment lift lever.

2.Start mower blades by engaging attachment clutch.

TO STOP MOWER BLADES - disengage attachment clutch control.

S

FIG. 10

10

Page 9 Page 11
Image 10
Page 9 Page 11
Contents YTH21K46 General Operation Safety RulesSafe Operation Practices for Ride-On Mowers II. Slope OperationIII. Children ServiceGeneral Service IV. TowingTable of Contents To Remove Tractor from Carton AssemblyUnassembled Parts Unpack CartonCheck for Proper Position of ALL Belts Check Tire PressureCheck Deck Levelness Check Brake SystemOperation Know Your Tractor To SET Parking Brake See Fig HOW to USE Your TractorAttachment Clutch Switch Disengaged Engaged Stopping See FigTo Move Forward and Backward See Fig To Adjust Mower Cutting Height See FigTo Adjust Gauge Wheels See Fig To USE Cruise Control J See FigReverse Operation System ROS See Fig Service REMINDER/HOUR MeterUsing the Reverse Operation System To Operate on HillsADD Gasoline Before Starting the EngineCheck Engine OIL Level To Start Engine See FigMowing Tips Purge TransmissionGeneral Recommendations MaintenanceMaintenance ScheduleBlade Care BatteryTractor Blade Removal See FigEngine IN-LINE Fuel Filter See Fig CleaningSpark Plugs Deck Washout Port See FigTo Install Mower See Fig Service and AdjustmentsTo Remove Mower See Fig Install belt on engine pulley M, in belt keepers G Visual SIDE-TO-SIDE Adjustment See Fig To Level MowerTo Check Brake Belt InstallationTo Replace Mower Blade Drive Belt See Fig To Replace Motion Drive Belt See FigFront Wheel TOE-IN/CAMBER To Start Engine with a Weak Battery See FigReplacing Battery See Fig To Remove Wheel for Repairs See FigTransmission Fuel System StorageOther Engine OILTroubleshooting Points Problem Cause CorrectionEngine continues Schematic Tractor - Model Number YTH21K46 96045002101, Product no 45Electrical KEY Part Description Chassis Tractor - Model Number YTH21K46 96045002101, Product no 45 Drive T2-AABC-1X2B-1GX1 30!2+ª!22%34%2ª+4 EngineEngine Kohler Model No. SV610-0212 Steering Assembly Tractor - Model Number YTH21K46 96045002101, Product no 45 Mower Deck KEY Part NO. no Description Mower Lift 8787 100 101Seat Assembly 532 42 SeatDecals Wheels and TiresSuggested Guide for Sighting Slopes for Safe Operation Only Ride UP and Down Hill Not Across Hill Degrees MAX06.23.10 JA

96045002101, 532 43 70-40 specifications

The Husqvarna 532 43 70-40,96045002101 is a standout lawn mower blade designed specifically for select Husqvarna lawn mower models. Known for its durability and precision cutting ability, this blade plays a vital role in maintaining a pristine lawn, contributing to overall landscaping health and aesthetic appeal.

This high-performance mower blade measures 21 inches in length, making it ideal for medium to large-sized lawns. One of its main features is the enhanced cutting edge, which delivers a sharp and precise cut, allowing grass to be trimmed cleanly. This results in a healthier lawn, as the cut grass blades are less prone to disease and desiccation.

Manufactured from high-quality steel, the Husqvarna 532 43 70-40,96045002101 is designed to withstand the rigors of frequent use while exhibiting resistance to wear and tear. This includes a corrosion-resistant coating that ensures longevity, even when exposed to various weather conditions and grass types. This blade is engineered for easy installation, featuring holes and dimensions that align perfectly with compatible Husqvarna mower models, making it user-friendly for both professionals and DIY enthusiasts.

In addition to its rugged construction, this mower blade incorporates advanced technologies that enhance overall mowing efficiency. The aerodynamic design allows for better airflow, facilitating grass discharge and promoting an even cut. This design also contributes to improved fuel efficiency, making mowing sessions less taxing on resources, whether gasoline for push mowers or battery life for electric mowers.

Another noteworthy characteristic of the Husqvarna 532 43 70-40,96045002101 is its compatibility with a range of Husqvarna mower models. This versatility ensures that users can easily find a replacement blade that fits their equipment, which helps to minimize downtime and maintain a consistent mowing schedule.

In conclusion, the Husqvarna 532 43 70-40,96045002101 lawn mower blade is an excellent choice for anyone looking to improve their lawn's health and appearance. Its quality construction, advanced cutting technologies, and compatibility make it a reliable option for effective lawn care. By investing in this blade, users can expect improved performance and a beautifully manicured lawn throughout the mowing season.
Top Page Image Contents