Husqvarna 532 43 70-40, 96045002101 owner manual Mowing Tips, Purge Transmission

Page 13

OPERATION

PURGE TRANSMISSION

CAUTION: Never engage or disengage freewheel lever while the engine is running.

To ensure proper operation and performance, it is recom- mended that the transmission be purged before operating tractor for the first time. This procedure will remove any trapped air inside the transmission which may have devel- oped during shipping of your tractor.

IMPORTANT: SHOULD YOUR TRANSMISSION REQUIRE REMOVAL FOR SERVICE OR REPLACEMENT, IT SHOULD BE PURGED AFTER REINSTALLATION BEFORE OPERATING THE TRACTOR.

•Place tractor safely on a level surface - that is clear and open - with engine off and parking brake set.

•Disengage transmission by placing freewheel control in freewheeling position (See “TO TRANSPORT” in this section of manual).

•Sitting in the tractor seat, start engine. After the en- gine is running, move throttle control to slow position. Disengage parking brake

CAUTION: At any time, there may be movement of the drive wheels.

•Depress forward drive pedal to full forward position, hold for five (5) seconds and release pedal. Depress reverse drive pedal to full reverse position, hold for five

(5) seconds and release pedal. Repeat this procedure three (3) times.

•Shut off engine and set parking brake.

•Engage transmission by placing freewheel control in engaged position (See “TO TRANSPORT” in this sec- tion of manual).

•Sitting in the tractor seat, start engine. After the engine is running, move throttle control to half (1/2) speed. Disengage parking brake.

•Drive tractor forward for approximately five feet then backwards for five feet. Repeat this driving procedure three times.

Your transmission is now purged and now ready for normal operation.

MOWING TIPS

•Mower should be properly leveled for best mowing performance. See “TO LEVEL MOWER HOUSING” in the Service and Adjustments section of this manual.

•The left hand side of mower should be used for trim- ming.

•Drive so that clippings are discharged onto the area that has been cut. Have the cut area to the right of the machine. This will result in a more even distribution of clippings and more uniform cutting.

•When mowing large areas, start by turning to the right so that clippings will discharge away from shrubs, fences, driveways, etc. After one or two rounds, mow in the opposite direction making left hand turns until finished (See Fig. 13).

FIG. 13

•If grass is extremely tall, it should be mowed twice to reduce load and possible fire hazard from dried clip- pings. Make first cut relatively high; the second to the desired height.

•Do not mow grass when it is wet. Wet grass will plug mower and leave undesirable clumps. Allow grass to dry before mowing.

•Always operate engine at full throttle when mow- ing to assure better mowing performance and proper discharge of material. Regulate ground speed by se- lecting a low enough gear to give the mower cutting performance as well as the quality of cut desired.

•When operating attachments, select a ground speed that will suit the terrain and give best performance of the attachment being used.

13

Page 12 Page 14
Image 13
Page 12 Page 14
Contents YTH21K46 Safe Operation Practices for Ride-On Mowers Safety RulesGeneral Operation II. Slope OperationGeneral Service ServiceIII. Children IV. TowingTable of Contents Unassembled Parts AssemblyTo Remove Tractor from Carton Unpack CartonCheck Deck Levelness Check Tire PressureCheck for Proper Position of ALL Belts Check Brake SystemOperation Know Your Tractor Attachment Clutch Switch Disengaged Engaged HOW to USE Your TractorTo SET Parking Brake See Fig Stopping See FigTo Adjust Gauge Wheels See Fig To Adjust Mower Cutting Height See FigTo Move Forward and Backward See Fig To USE Cruise Control J See FigUsing the Reverse Operation System Service REMINDER/HOUR MeterReverse Operation System ROS See Fig To Operate on HillsCheck Engine OIL Level Before Starting the EngineADD Gasoline To Start Engine See FigPurge Transmission Mowing TipsMaintenance MaintenanceGeneral Recommendations ScheduleTractor BatteryBlade Care Blade Removal See FigEngine Spark Plugs CleaningIN-LINE Fuel Filter See Fig Deck Washout Port See FigTo Install Mower See Fig Service and AdjustmentsTo Remove Mower See Fig Install belt on engine pulley M, in belt keepers G To Level Mower Visual SIDE-TO-SIDE Adjustment See FigTo Replace Mower Blade Drive Belt See Fig Belt InstallationTo Check Brake To Replace Motion Drive Belt See FigReplacing Battery See Fig To Start Engine with a Weak Battery See FigFront Wheel TOE-IN/CAMBER To Remove Wheel for Repairs See FigTransmission Other StorageFuel System Engine OILProblem Cause Correction Troubleshooting PointsEngine continues Tractor - Model Number YTH21K46 96045002101, Product no 45 SchematicElectrical KEY Part Description Chassis Tractor - Model Number YTH21K46 96045002101, Product no 45 Drive T2-AABC-1X2B-1GX1 Engine 30!2+ª!22%34%2ª+4Engine Kohler Model No. SV610-0212 Steering Assembly Tractor - Model Number YTH21K46 96045002101, Product no 45 Mower Deck KEY Part NO. no Description 8787 100 101 Mower Lift532 42 Seat Seat AssemblyWheels and Tires DecalsOnly Ride UP and Down Hill Not Across Hill Degrees MAX Suggested Guide for Sighting Slopes for Safe Operation06.23.10 JA

96045002101, 532 43 70-40 specifications

The Husqvarna 532 43 70-40,96045002101 is a standout lawn mower blade designed specifically for select Husqvarna lawn mower models. Known for its durability and precision cutting ability, this blade plays a vital role in maintaining a pristine lawn, contributing to overall landscaping health and aesthetic appeal.

This high-performance mower blade measures 21 inches in length, making it ideal for medium to large-sized lawns. One of its main features is the enhanced cutting edge, which delivers a sharp and precise cut, allowing grass to be trimmed cleanly. This results in a healthier lawn, as the cut grass blades are less prone to disease and desiccation.

Manufactured from high-quality steel, the Husqvarna 532 43 70-40,96045002101 is designed to withstand the rigors of frequent use while exhibiting resistance to wear and tear. This includes a corrosion-resistant coating that ensures longevity, even when exposed to various weather conditions and grass types. This blade is engineered for easy installation, featuring holes and dimensions that align perfectly with compatible Husqvarna mower models, making it user-friendly for both professionals and DIY enthusiasts.

In addition to its rugged construction, this mower blade incorporates advanced technologies that enhance overall mowing efficiency. The aerodynamic design allows for better airflow, facilitating grass discharge and promoting an even cut. This design also contributes to improved fuel efficiency, making mowing sessions less taxing on resources, whether gasoline for push mowers or battery life for electric mowers.

Another noteworthy characteristic of the Husqvarna 532 43 70-40,96045002101 is its compatibility with a range of Husqvarna mower models. This versatility ensures that users can easily find a replacement blade that fits their equipment, which helps to minimize downtime and maintain a consistent mowing schedule.

In conclusion, the Husqvarna 532 43 70-40,96045002101 lawn mower blade is an excellent choice for anyone looking to improve their lawn's health and appearance. Its quality construction, advanced cutting technologies, and compatibility make it a reliable option for effective lawn care. By investing in this blade, users can expect improved performance and a beautifully manicured lawn throughout the mowing season.
Top Page Image Contents