Husqvarna 96045002101 Before Starting the Engine, Check Engine OIL Level, ADD Gasoline

Page 12

OPERATION

BEFORE STARTING THE ENGINE

CHECK ENGINE OIL LEVEL

The engine in your tractor has been shipped, from the factory, already filled with summer weight oil.

•Check engine oil with tractor on level ground.

•Remove oil fill cap/dipstick and wipe clean, reinsert the dipstick and screw cap tight, wait for a few seconds, remove and read oil level. If necessary, add oil until “FULL” mark on dipstick is reached. Do not overfill.

•For cold weather operation you should change oil for easier starting (See “OIL VISCOSITY CHART” in the Maintenance section of this manual).

•To change engine oil, see the Maintenance section in this manual.

ADD GASOLINE

•Fill fuel tank to bottom of filler neck. Do not overfill. Use fresh, clean, regular unleaded gasoline with a minimum of 87 octane. (Use of leaded gasoline will increase carbon and lead oxide deposits and reduce valve life). Do not mix oil with gasoline. Purchase fuel in quantities that can be used within 30 days to assure fuel freshness.

CAUTION: Wipe off any spilled oil or fuel. Do not store, spill or use gasoline near an open flame.

IMPORTANT: WHEN OPERATING IN TEMPERATURES BELOW 32°F(0°C), USE FRESH, CLEAN WINTER GRADE GASOLINE TO HELP INSURE GOOD COLD WEATHER STARTING.

CAUTION: Alcohol blended fuels (called gasohol or using ethanol or methanol) can attract moisture which leads to separation and formation of acids during storage. Acidic gas can damage the fuel system of an engine while in storage. To avoid engine problems, the fuel system should be emptied before storage of 30 days or longer. Drain the gas tank, start the engine and let it run until the fuel lines and carburetor are empty. Use fresh fuel next season. See Storage Instructions for additional information. Never use engine or carburetor cleaner products in the fuel tank or permanent damage may occur.

TO START ENGINE (See Fig. 3)

When starting the engine for the first time or if the engine has run out of fuel, it will take extra cranking time to move fuel from the tank to the engine.

•Be sure freewheel control is in the transmission engaged position.

•Sit on seat in operating position, depress brake pedal and set parking brake.

•Move attachment clutch to “DISENGAGED” position.

•Move throttle control to choke position.

NOTE: Before starting, read the warm and cold starting procedures below.

•Insert key into ignition and turn key clockwise to “START” position and release key as soon as engine starts. Do not run starter continuously for more than fifteen seconds per minute. If the engine does not start after several at- tempts, move throttle control to fast position, wait a few minutes and try again. If engine still does not start, move the throttle control back to the choke position and retry.

WARM WEATHER STARTING (50° F and above)

•When engine starts, move the throttle control to the fast position.

•The attachments and ground drive can now be used. If the engine does not accept the load, restart the engine and allow it to warm up for one minute using the choke as described above.

COLD WEATHER STARTING (50° F and below)

•When engine starts, allow engine to run with the throttle control in the choke position until the engine runs rough- ly, then move throttle control to fast position. This may require an engine warm-up period from several seconds to several minutes, depending on the temperature.

AUTOMATIC TRANSMISSION WARM UP

•Before driving the unit in cold weather, the transmission should be warmed up as follows:

•Be sure the tractor is on level ground.

•Release the parking brake and let the brake slowly return to operating position.

•Allow one minute for transmission to warm up. This can be done during the engine warm up period.

•Theattachmentscanalsobeusedduringtheenginewarm- up period after the transmission has been warmed up.

NOTE: If at a high altitude (above 3000 feet) or in cold temperatures (below 32° F) the carburetor fuel mixture may need to be adjusted for best engine performance. See “TO ADJUST CARBURETOR” in the Service and Adjustments section of this manual.

12

Page 11 Page 13
Image 12
Page 11 Page 13
Contents YTH21K46 Safety Rules Safe Operation Practices for Ride-On MowersGeneral Operation II. Slope OperationService General ServiceIII. Children IV. TowingTable of Contents Assembly Unassembled PartsTo Remove Tractor from Carton Unpack CartonCheck Tire Pressure Check Deck LevelnessCheck for Proper Position of ALL Belts Check Brake SystemOperation Know Your Tractor HOW to USE Your Tractor Attachment Clutch Switch Disengaged EngagedTo SET Parking Brake See Fig Stopping See FigTo Adjust Mower Cutting Height See Fig To Adjust Gauge Wheels See FigTo Move Forward and Backward See Fig To USE Cruise Control J See FigService REMINDER/HOUR Meter Using the Reverse Operation SystemReverse Operation System ROS See Fig To Operate on HillsBefore Starting the Engine Check Engine OIL LevelADD Gasoline To Start Engine See FigMowing Tips Purge TransmissionMaintenance MaintenanceGeneral Recommendations ScheduleBattery TractorBlade Care Blade Removal See FigEngine Cleaning Spark PlugsIN-LINE Fuel Filter See Fig Deck Washout Port See FigService and Adjustments To Install Mower See FigTo Remove Mower See Fig Install belt on engine pulley M, in belt keepers G Visual SIDE-TO-SIDE Adjustment See Fig To Level MowerBelt Installation To Replace Mower Blade Drive Belt See FigTo Check Brake To Replace Motion Drive Belt See FigTo Start Engine with a Weak Battery See Fig Replacing Battery See FigFront Wheel TOE-IN/CAMBER To Remove Wheel for Repairs See FigTransmission Storage OtherFuel System Engine OILTroubleshooting Points Problem Cause CorrectionEngine continues Schematic Tractor - Model Number YTH21K46 96045002101, Product no 45Electrical KEY Part Description Chassis Tractor - Model Number YTH21K46 96045002101, Product no 45 Drive T2-AABC-1X2B-1GX1 30!2+ª!22%34%2ª+4 EngineEngine Kohler Model No. SV610-0212 Steering Assembly Tractor - Model Number YTH21K46 96045002101, Product no 45 Mower Deck KEY Part NO. no Description Mower Lift 8787 100 101Seat Assembly 532 42 SeatDecals Wheels and TiresSuggested Guide for Sighting Slopes for Safe Operation Only Ride UP and Down Hill Not Across Hill Degrees MAX06.23.10 JA

96045002101, 532 43 70-40 specifications

The Husqvarna 532 43 70-40,96045002101 is a standout lawn mower blade designed specifically for select Husqvarna lawn mower models. Known for its durability and precision cutting ability, this blade plays a vital role in maintaining a pristine lawn, contributing to overall landscaping health and aesthetic appeal.

This high-performance mower blade measures 21 inches in length, making it ideal for medium to large-sized lawns. One of its main features is the enhanced cutting edge, which delivers a sharp and precise cut, allowing grass to be trimmed cleanly. This results in a healthier lawn, as the cut grass blades are less prone to disease and desiccation.

Manufactured from high-quality steel, the Husqvarna 532 43 70-40,96045002101 is designed to withstand the rigors of frequent use while exhibiting resistance to wear and tear. This includes a corrosion-resistant coating that ensures longevity, even when exposed to various weather conditions and grass types. This blade is engineered for easy installation, featuring holes and dimensions that align perfectly with compatible Husqvarna mower models, making it user-friendly for both professionals and DIY enthusiasts.

In addition to its rugged construction, this mower blade incorporates advanced technologies that enhance overall mowing efficiency. The aerodynamic design allows for better airflow, facilitating grass discharge and promoting an even cut. This design also contributes to improved fuel efficiency, making mowing sessions less taxing on resources, whether gasoline for push mowers or battery life for electric mowers.

Another noteworthy characteristic of the Husqvarna 532 43 70-40,96045002101 is its compatibility with a range of Husqvarna mower models. This versatility ensures that users can easily find a replacement blade that fits their equipment, which helps to minimize downtime and maintain a consistent mowing schedule.

In conclusion, the Husqvarna 532 43 70-40,96045002101 lawn mower blade is an excellent choice for anyone looking to improve their lawn's health and appearance. Its quality construction, advanced cutting technologies, and compatibility make it a reliable option for effective lawn care. By investing in this blade, users can expect improved performance and a beautifully manicured lawn throughout the mowing season.
Top Page Image Contents