Husqvarna 96045002101, 532 43 70-40 owner manual Storage, Other, Fuel System, Engine OIL, Cylinders

Page 24

STORAGE

Immediately prepare your tractor for storage at the end of the season or if the tractor will not be used for 30 days or more.

WARNING: Never store the tractor with gasoline in the tank inside a building where fumes may reach an open flame or spark. Allow the engine to cool before storing in any enclosure.

TRACTOR

Remove mower from tractor for winter storage. When mower is to be stored for a period of time, clean it thoroughly, remove all dirt, grease, leaves, etc. Store in a clean, dry area.

Clean entire tractor (See “CLEANING” in the Mainte- nance section of this manual).

Inspect and replace belts, if necessary (See belt re- placement instructions in the Service and Adjustments section of this manual).

Lubricate as shown in the Maintenance section of this manual.

Be sure that all nuts, bolts and screws are securely fastened. Inspect moving parts for damage, breakage and wear. Replace if necessary.

Touch up all rusted or chipped paint surfaces; sand lightly before painting.

BATTERY

Fully charge the battery for storage.

After a period of time in storage, battery may require recharging.

To help prevent corrosion and power leakage during long periods of storage, battery cables should be dis- connected and battery cleaned thoroughly (See “TO CLEAN BATTERY AND TERMINALS” in the Mainte- nance section of this manual).

After cleaning, leave cables disconnected and place cables where they cannot come in contact with battery terminals.

If battery is removed from tractor for storage, do not store battery directly on concrete or damp surfaces.

ENGINE

FUEL SYSTEM

IMPORTANT: IT IS IMPORTANT TO PREVENT GUM DEPOSITS FROM FORMING IN ESSENTIAL FUEL SYSTEM PARTS SUCH AS CARBURETOR, FUEL FILTER, FUEL HOSE, OR TANK DURING STORAGE. ALSO, EXPERIENCE INDICATES THAT ALCOHOL BLENDED FUELS (CALLED GASOHOL OR USING ETHANOL OR METHANOL) CAN ATTRACT MOISTURE WHICH LEADS TO SEPARATION AND FORMATION OF ACIDS DURING STORAGE. ACIDIC GAS CAN DAMAGE THE FUEL SYSTEM OF AN ENGINE WHILE IN STORAGE.

Empty the fuel tank by starting the engine and let it run until the fuel lines and carburetor are empty.

Never use engine or carburetor cleaner products in the fuel tank or permanent damage may occur.

Use fresh fuel next season.

NOTE: Fuel stabilizer is an acceptable alternative in mini- mizing the formation of fuel gum deposits during storage. Add stabilizer to gasoline in fuel tank or storage container. Always follow the mix ratio found on stabilizer container. Run engine at least 10 minutes after adding stabilizer to allow the stabilizer to reach the carburetor. Do not empty the gas tank and carburetor if using fuel stabilizer.

ENGINE OIL

Drain oil (with engine warm) and replace with clean engine oil. (See “ENGINE” in the Maintenance section of this manual).

CYLINDER(S)

Remove spark plug(s).

Pour one ounce of oil through spark plug hole(s) into cylinder(s).

Turn ignition key to “START” position for a few seconds to distribute oil.

Replace with new spark plug(s).

OTHER

Do not store gasoline from one season to another.

Replace your gasoline can if your can starts to rust. Rust and/or dirt in your gasoline will cause problems.

If possible, store your tractor indoors and cover it to give protection from dust and dirt.

Cover your tractor with a suitable protective cover that does not retain moisture. Do not use plastic. Plastic cannot breathe which allows condensation to form and will cause your tractor to rust.

IMPORTANT: NEVER COVER TRACTOR WHILE ENGINE AND EXHAUST AREAS ARE STILL WARM.

24

Image 24
Contents YTH21K46 Safety Rules Safe Operation Practices for Ride-On MowersGeneral Operation II. Slope OperationService General ServiceIII. Children IV. TowingTable of Contents Assembly Unassembled PartsTo Remove Tractor from Carton Unpack CartonCheck Tire Pressure Check Deck LevelnessCheck for Proper Position of ALL Belts Check Brake SystemOperation Know Your Tractor HOW to USE Your Tractor Attachment Clutch Switch Disengaged EngagedTo SET Parking Brake See Fig Stopping See FigTo Adjust Mower Cutting Height See Fig To Adjust Gauge Wheels See FigTo Move Forward and Backward See Fig To USE Cruise Control J See FigService REMINDER/HOUR Meter Using the Reverse Operation SystemReverse Operation System ROS See Fig To Operate on HillsBefore Starting the Engine Check Engine OIL LevelADD Gasoline To Start Engine See FigMowing Tips Purge TransmissionMaintenance MaintenanceGeneral Recommendations ScheduleBattery TractorBlade Care Blade Removal See FigEngine Cleaning Spark PlugsIN-LINE Fuel Filter See Fig Deck Washout Port See FigService and Adjustments To Install Mower See FigTo Remove Mower See Fig Install belt on engine pulley M, in belt keepers G Visual SIDE-TO-SIDE Adjustment See Fig To Level MowerBelt Installation To Replace Mower Blade Drive Belt See FigTo Check Brake To Replace Motion Drive Belt See FigTo Start Engine with a Weak Battery See Fig Replacing Battery See FigFront Wheel TOE-IN/CAMBER To Remove Wheel for Repairs See FigTransmission Storage OtherFuel System Engine OILTroubleshooting Points Problem Cause CorrectionEngine continues Schematic Tractor - Model Number YTH21K46 96045002101, Product no 45Electrical KEY Part Description Chassis Tractor - Model Number YTH21K46 96045002101, Product no 45 Drive T2-AABC-1X2B-1GX1 30!2+ª!22%34%2ª+4 EngineEngine Kohler Model No. SV610-0212 Steering Assembly Tractor - Model Number YTH21K46 96045002101, Product no 45 Mower Deck KEY Part NO. no Description Mower Lift 8787 100 101Seat Assembly 532 42 SeatDecals Wheels and TiresSuggested Guide for Sighting Slopes for Safe Operation Only Ride UP and Down Hill Not Across Hill Degrees MAX06.23.10 JA

96045002101, 532 43 70-40 specifications

The Husqvarna 532 43 70-40,96045002101 is a standout lawn mower blade designed specifically for select Husqvarna lawn mower models. Known for its durability and precision cutting ability, this blade plays a vital role in maintaining a pristine lawn, contributing to overall landscaping health and aesthetic appeal.

This high-performance mower blade measures 21 inches in length, making it ideal for medium to large-sized lawns. One of its main features is the enhanced cutting edge, which delivers a sharp and precise cut, allowing grass to be trimmed cleanly. This results in a healthier lawn, as the cut grass blades are less prone to disease and desiccation.

Manufactured from high-quality steel, the Husqvarna 532 43 70-40,96045002101 is designed to withstand the rigors of frequent use while exhibiting resistance to wear and tear. This includes a corrosion-resistant coating that ensures longevity, even when exposed to various weather conditions and grass types. This blade is engineered for easy installation, featuring holes and dimensions that align perfectly with compatible Husqvarna mower models, making it user-friendly for both professionals and DIY enthusiasts.

In addition to its rugged construction, this mower blade incorporates advanced technologies that enhance overall mowing efficiency. The aerodynamic design allows for better airflow, facilitating grass discharge and promoting an even cut. This design also contributes to improved fuel efficiency, making mowing sessions less taxing on resources, whether gasoline for push mowers or battery life for electric mowers.

Another noteworthy characteristic of the Husqvarna 532 43 70-40,96045002101 is its compatibility with a range of Husqvarna mower models. This versatility ensures that users can easily find a replacement blade that fits their equipment, which helps to minimize downtime and maintain a consistent mowing schedule.

In conclusion, the Husqvarna 532 43 70-40,96045002101 lawn mower blade is an excellent choice for anyone looking to improve their lawn's health and appearance. Its quality construction, advanced cutting technologies, and compatibility make it a reliable option for effective lawn care. By investing in this blade, users can expect improved performance and a beautifully manicured lawn throughout the mowing season.