Husqvarna 96045002101 owner manual Front Wheel TOE-IN/CAMBER, To Remove Wheel for Repairs See Fig

Page 22

SERVICE AND ADJUSTMENTS

FRONT WHEEL TOE-IN/CAMBER

Your new tractor front wheel toe-in and camber is set at the factory and is normal. The front wheel toe-in and camber are not adjustable. If damage has occurred to affect the factory set front wheel toe-in or camber, contact a qualified service center.

TO REMOVE WHEEL FOR REPAIRS (See Fig. 32)

•Block up axle securely.

•Remove axle cover, retaining ring and washers to allow wheel removal (rear wheel contains a square key - Do not lose).

•Repair tire and reassemble.

•On rear wheels only: align grooves in rear wheel hub and axle. Insert square key.

•Replace washers and snap retaining ring securely in axle groove.

•Replace axle cover.

NOTE: To seal tire punctures and prevent flat tires due to slow leaks, tire sealant may be purchased from your local parts dealer. Tire sealant also prevents tire dry rot and corrosion.

WASHERS

RETAINING

RING

AXLE COVER

SQUARE KEY (REAR

WHEEL ONLY)

FIG. 32

TO START ENGINE WITH A WEAK BATTERY (See Fig. 33)

WARNING: Lead-acid batteries gen- erate explosive gases. Keep sparks, flame and smoking materials away from batteries. Always wear eye protection when around batteries.

If your battery is too weak to start the engine, it should be recharged. (See "BATTERY" in the MAINTENANCE sec- tion of this manual).

If “jumper cables” are used for emergency starting, follow this procedure:

IMPORTANT: YOUR TRACTOR IS EQUIPPED WITH A 12 VOLT SYSTEM. THE OTHER VEHICLE MUST ALSO BE A 12 VOLT SYSTEM. DO NOT USE YOUR TRACTOR BATTERY TO START OTHER VEHICLES.

TO ATTACH JUMPER CABLES -

•Connect one end of the RED cable to the POSITIVE

(+)terminal of each battery(A-B), taking care not to short against tractor chassis.

•Connect one end of the BLACK cable to the NEGATIVE (-) terminal (C) of fully charged battery.

•Connect the other end of the BLACK cable (D) to good chassis ground, away from fuel tank and battery.

TO REMOVE CABLES, REVERSE ORDER -

•BLACK cable first from chassis and then from the fully charged battery.

•RED cable last from both batteries.

WEAK OR DEAD

FULLY CHARGED

BATTERY

BATTERY

FIG. 33

REPLACING BATTERY (See Fig. 34)

WARNING: Do not short battery termi- nals by allowing a wrench or any other object to contact both terminals at the same time. Before connecting battery, remove metal bracelets, wristwatch bands, rings, etc. Positive terminal must be connected first to prevent sparking from accidental grounding.

•Lift seat pan to raised position.

•Disconnect BLACK battery cable first then RED battery cable and carefully remove battery from tractor.

•Install new battery with terminals in same position as old battery.

SEAT PAN

 

TERMINAL

NUT

COVER

BOLT

 

POSITIVE

NEGATIVE

(RED)

(BLACK)

CABLE

CABLE

02603

 

FIG. 34

22

Page 21 Page 23
Image 22
Page 21 Page 23
Contents YTH21K46 General Operation Safety RulesSafe Operation Practices for Ride-On Mowers II. Slope OperationIII. Children ServiceGeneral Service IV. TowingTable of Contents To Remove Tractor from Carton AssemblyUnassembled Parts Unpack CartonCheck for Proper Position of ALL Belts Check Tire PressureCheck Deck Levelness Check Brake SystemOperation Know Your Tractor To SET Parking Brake See Fig HOW to USE Your TractorAttachment Clutch Switch Disengaged Engaged Stopping See FigTo Move Forward and Backward See Fig To Adjust Mower Cutting Height See FigTo Adjust Gauge Wheels See Fig To USE Cruise Control J See FigReverse Operation System ROS See Fig Service REMINDER/HOUR MeterUsing the Reverse Operation System To Operate on HillsADD Gasoline Before Starting the EngineCheck Engine OIL Level To Start Engine See FigMowing Tips Purge TransmissionGeneral Recommendations MaintenanceMaintenance ScheduleBlade Care BatteryTractor Blade Removal See FigEngine IN-LINE Fuel Filter See Fig CleaningSpark Plugs Deck Washout Port See FigTo Install Mower See Fig Service and AdjustmentsTo Remove Mower See Fig Install belt on engine pulley M, in belt keepers G Visual SIDE-TO-SIDE Adjustment See Fig To Level MowerTo Check Brake Belt InstallationTo Replace Mower Blade Drive Belt See Fig To Replace Motion Drive Belt See FigFront Wheel TOE-IN/CAMBER To Start Engine with a Weak Battery See FigReplacing Battery See Fig To Remove Wheel for Repairs See FigTransmission Fuel System StorageOther Engine OILTroubleshooting Points Problem Cause CorrectionEngine continues Schematic Tractor - Model Number YTH21K46 96045002101, Product no 45Electrical KEY Part Description Chassis Tractor - Model Number YTH21K46 96045002101, Product no 45 Drive T2-AABC-1X2B-1GX1 30!2+ª!22%34%2ª+4 EngineEngine Kohler Model No. SV610-0212 Steering Assembly Tractor - Model Number YTH21K46 96045002101, Product no 45 Mower Deck KEY Part NO. no Description Mower Lift 8787 100 101Seat Assembly 532 42 SeatDecals Wheels and TiresSuggested Guide for Sighting Slopes for Safe Operation Only Ride UP and Down Hill Not Across Hill Degrees MAX06.23.10 JA

96045002101, 532 43 70-40 specifications

The Husqvarna 532 43 70-40,96045002101 is a standout lawn mower blade designed specifically for select Husqvarna lawn mower models. Known for its durability and precision cutting ability, this blade plays a vital role in maintaining a pristine lawn, contributing to overall landscaping health and aesthetic appeal.

This high-performance mower blade measures 21 inches in length, making it ideal for medium to large-sized lawns. One of its main features is the enhanced cutting edge, which delivers a sharp and precise cut, allowing grass to be trimmed cleanly. This results in a healthier lawn, as the cut grass blades are less prone to disease and desiccation.

Manufactured from high-quality steel, the Husqvarna 532 43 70-40,96045002101 is designed to withstand the rigors of frequent use while exhibiting resistance to wear and tear. This includes a corrosion-resistant coating that ensures longevity, even when exposed to various weather conditions and grass types. This blade is engineered for easy installation, featuring holes and dimensions that align perfectly with compatible Husqvarna mower models, making it user-friendly for both professionals and DIY enthusiasts.

In addition to its rugged construction, this mower blade incorporates advanced technologies that enhance overall mowing efficiency. The aerodynamic design allows for better airflow, facilitating grass discharge and promoting an even cut. This design also contributes to improved fuel efficiency, making mowing sessions less taxing on resources, whether gasoline for push mowers or battery life for electric mowers.

Another noteworthy characteristic of the Husqvarna 532 43 70-40,96045002101 is its compatibility with a range of Husqvarna mower models. This versatility ensures that users can easily find a replacement blade that fits their equipment, which helps to minimize downtime and maintain a consistent mowing schedule.

In conclusion, the Husqvarna 532 43 70-40,96045002101 lawn mower blade is an excellent choice for anyone looking to improve their lawn's health and appearance. Its quality construction, advanced cutting technologies, and compatibility make it a reliable option for effective lawn care. By investing in this blade, users can expect improved performance and a beautifully manicured lawn throughout the mowing season.
Top Page Image Contents