Husqvarna 365, 372XP manual Tensioning the chain, General advice on setting raker clearance

Page 12

SAFETY INSTRUCTIONS

•Always file cutting teeth from the inside face. Reduce the pressure on the return stroke. File all the teeth on one side first, then turn the chain saw over and file the teeth on the other side.

•File all the teeth to the same length. When the length of the cutting teeth is reduced to 4 mm (0.16") the chain is worn out and should be replaced.

General advice on setting raker clearance

•When you sharpen the cutting teeth you reduce the raker clearance (=cutting depth). To maintain optimal cutting performance you must file back the raker lip to the recommended height.

See the Technical data section to find the raker clearance for your particular chain.

•On a low-kickback cutting link the front edge of the raker lip is rounded. It is very important that you maintain this radius or bevel when you adjust the raker clearance.

•We recommend that you use our raker gauge to achieve the correct clearance and bevel on the raker lip.

WARNING! The risk of kickback is increased

!if the raker clearance is too large!

Setting the raker clearance

•Before setting the raker clearance the cutting teeth should be newly sharpened. We recommend that you adjust the raker clearance every third time you sharpen the chain.

NOTE! This recommendation assumes that the length of the cutting teeth is not reduced excessively.

•To adjust the raker clearance you will need a flat file and a raker gauge.

•Place the gauge over the raker lip.

•Place the file over the part of the lip that protrudes through the gauge and file off the excess. The clearance is correct when you no longer feel any resistance as you draw the file over the gauge.

Tensioning the chain

WARNING! A slack chain may jump off and

!cause serious or even fatal injury.

The more you use a chain the longer it becomes. It is therefore important to adjust the chain regularly to take up the slack.

Check the chain tension every time you refuel. NOTE! A new chain has a running-in period during which you should check the tension more frequently.

The position of the chain tensioning screw on our chain saws varies from model to model. See the What is what? section to find out where it is on your model.

Tension the chain as tightly as possible, but not so tight that you cannot pull it round freely by hand.

•Undo the bar nuts that hold the clutch cover/chain brake. Use the combination spanner. Then tighten the bar nuts by hand as tight as you can.

12 – English

Page 11 Page 13
Image 12
Page 11 Page 13
Contents 362XP 365 372XP KEY to Symbols Key to symbolsContents Safety Instructions Machine′s safety equipmentPersonal protective equipment Chain brake and front hand guard Stop switch Throttle lockChain catcher Right hand guardMuffler Checking brake band wearChecking the front hand guard Checking the inertia brake releaseStop switch Throttle lockChain catcher Right hand guardCutting equipment General rulesCutting equipment designed to minimise kickback MufflerChain Some terms that describe the bar and chainSharpening your chain and adjusting raker clearance General information on sharpening cutting teethSharpening cutting teeth With a badly sharpened chainGeneral advice on setting raker clearance Setting the raker clearanceTensioning the chain If the raker clearance is too largeLubricating cutting equipment Chain oilFilling with chain oil Checking chain lubricationLubricating the bar tip sprocket Needle bearing lubricationChecking wear on cutting equipment Chain drive sprocketHow to avoid kickback What is kickback?Do not let go of the handles General safety precautions Fuel safety StartingTransport and storage Basic safety rules General working instructionsBasic cutting technique GeneralTerms CuttingTree felling technique LimbingSafe distance Felling directionFelling Directional cutsFelling cut General advice Freeing a tree that has fallen badlyCutting the trunk into logs Freeing a trapped treeWhat is WHAT? What is what on the chain saw?Assembly Fitting the bar and chainFitting a spike bumper Working with the chainFuel Handling FuelFuelling Min 3 m 10ftStarting and Stopping Starting and stoppingCold engine Warm engineStopping Maintenance CarburettorCorrectly adjusted carburettor StarterHigh speed jet H Changing a broken or worn starter cordAir filter Spark plugTensioning the recoil spring Changing a broken recoil springAdjustment of the oil pump When making adjustmentsMuffler Needle bearing lubricationAir Injection centrifugal cleaning Heated handlesElectrical carburettor heating Winter useDaily maintenance Weekly maintenanceMonthly maintenance Below you will find some general maintenance instructionsTechnical Data Technical dataBar and chain combinations Bar ChainEC-declaration of conformity Applies to Europe onlyEN292-2, Cispr 121997, EN608 ´z+H4¶6j¨ Page 1140206-26 ´z+H4¶6j¨ ´z+H4¶6j¨
Related manuals
Manual 4 pages 16.24 Kb

372XP, 365 specifications

The Husqvarna 365 and 372XP chainsaws are powerful and versatile tools designed for both professional loggers and serious homeowners. Known for their robust construction and reliability, these models offer a perfect blend of performance and user-friendly features.

The Husqvarna 365 is equipped with a 70.7 cc engine that delivers impressive power, making it suitable for demanding cutting tasks. This chainsaw is designed for all-day use, ensuring that operators can tackle large trees and tough woods without losing momentum. The engine utilizes Smart Start technology, which allows for easier starting with minimal effort. This innovation reduces the resistance in the starter cord by up to 40%, enabling rapid and hassle-free ignition.

On the other hand, the Husqvarna 372XP boasts a slightly larger 72.2 cc engine, making it one of the most powerful saws in the market. Specifically tailored for professionals, this chainsaw excels in heavy-duty applications and has the ability to handle extreme workloads. Both models are designed with a high RPM, ensuring smooth cutting performance and efficient chip flow, which contributes to cleaner cuts and enhanced productivity.

A significant feature of these chainsaws is their ergonomic design, which includes a comfortable handle for better grip and control during operation. The chainsaws also feature an adjustable oil pump that allows users to customize the oil flow for the chain and bar, which helps minimize wear and prolongs the lifespan of the saw.

Safety is paramount with both the 365 and 372XP models. They are equipped with a chain brake system that automatically stops the chain in the event of kickback, ensuring user protection. Furthermore, the low vibration technology significantly reduces vibrations experienced by the operator, promoting comfort during prolonged use.

In terms of maintenance, both chainsaws come with a quick-release air filter that makes it easy to access and clean, ensuring optimal engine performance over time. The built-in fuel pump facilitates easier starting after long periods of inactivity, making these tools reliable for various cutting tasks.

In summary, the Husqvarna 365 and 372XP chainsaws stand out for their powerful engines, user-friendly features, and advanced safety technologies. They are engineered to meet the high demands of professional users while also being accessible for those who need a reliable chainsaw for home use. Whether for felling trees or limbing, these models deliver excellence in performance and durability.
Top Page Image Contents