Husqvarna 372XP, 365 manual Air Injection centrifugal cleaning, Heated handles, Winter use

Page 33

MAINTENANCE

”Air Injection” centrifugal cleaning

Centrifugal cleaning means the following: All air to the carburettor passes through the starter. Dirt and dust is centrifuged out by the cooling fan.

IMPORTANT! In order to maintain operation of the centrifugal cleaning system it must be regularly maintained.

•Clean the air intake to the starter, the fins on the flywheel, the space around the flywheel, inlet pipe and carburettor compartment.

Heated handles

(362XPG, 372XPG)

On models with the model code XPG/G both the front handle bar and the rear handle are equipped with electrical heating coils.These are supplied with electricity from a generator built into the chain saw.

When the red mark on the switch is visible, the heating is on.

Electrical carburettor heating

(362XPG, 372XPG)

This machine is equipped with an electronically controlled carburettor heater.

Applications

The carburettor heater is used in the following temperature range: ±0ºC or colder. During high humidity, icing of the carburettor can occur earlier than specified.

The carburettor heater only heats the carburettor when the 3- way switch is set to position ”II”.

The switch is off in position ”0”, supplies current to the handle heater in position ”I”, supplies current to the carburettor in position ”II”.

CAUTION! The carburettor heater reaches maximum temperature after about 3 minutes. It is therefore important that the machine is not run for longer with the heater switched on. If the switch is left on for too long the carburettor will overheat and lead to running problems or starting problems.

Winter use

During cold weather and under powder snow conditions, operating problems can arise due to:

•Too low engine temperature.

•Icing of the air filter and carburettor. Special measures are therefore often required:

•Partly mask the air inlet on the starter to increase the working temperature of the engine.

Temperature -5°C or colder:

For running the machine in cold weather or powder snow, a special cover is available, which is mounted on the starter housing.This reduces the intake of cold air and prevents large amounts of snow from being sucked in.

CAUTION! If the special winterising kit has been fitted or any measures have been taken to increase the temperature these changes must be reversed before the machine is used in normal temperature conditions. Otherwise there is a risk of overheating, resulting in severe damage to the engine.

IMPORTANT! Any maintenance other than that described in this manual must be carried out by your servicing dealer (retailer).

English – 33

Page 32 Page 34
Image 33
Page 32 Page 34
Contents 362XP 365 372XP Key to symbols KEY to SymbolsContents Safety Instructions Machine′s safety equipmentPersonal protective equipment Chain brake and front hand guard Throttle lock Stop switchChain catcher Right hand guardChecking brake band wear MufflerChecking the front hand guard Checking the inertia brake releaseThrottle lock Stop switchChain catcher Right hand guardGeneral rules Cutting equipmentCutting equipment designed to minimise kickback MufflerSome terms that describe the bar and chain ChainGeneral information on sharpening cutting teeth Sharpening your chain and adjusting raker clearanceSharpening cutting teeth With a badly sharpened chainSetting the raker clearance General advice on setting raker clearanceTensioning the chain If the raker clearance is too largeChain oil Lubricating cutting equipmentFilling with chain oil Checking chain lubricationNeedle bearing lubrication Lubricating the bar tip sprocketChecking wear on cutting equipment Chain drive sprocketHow to avoid kickback What is kickback?Do not let go of the handles General safety precautions Fuel safety StartingTransport and storage General working instructions Basic safety rulesBasic cutting technique GeneralCutting TermsLimbing Tree felling techniqueSafe distance Felling directionFelling Directional cutsFelling cut Freeing a tree that has fallen badly General adviceCutting the trunk into logs Freeing a trapped treeWhat is what on the chain saw? What is WHAT?Fitting the bar and chain AssemblyFitting a spike bumper Working with the chainFuel Fuel HandlingMin 3 m 10ft FuellingStarting and stopping Starting and StoppingCold engine Warm engineStopping Carburettor MaintenanceStarter Correctly adjusted carburettorHigh speed jet H Changing a broken or worn starter cordSpark plug Air filterTensioning the recoil spring Changing a broken recoil springWhen making adjustments Adjustment of the oil pumpMuffler Needle bearing lubricationHeated handles Air Injection centrifugal cleaningElectrical carburettor heating Winter useWeekly maintenance Daily maintenanceMonthly maintenance Below you will find some general maintenance instructionsTechnical data Technical DataBar Chain Bar and chain combinationsEC-declaration of conformity Applies to Europe onlyEN292-2, Cispr 121997, EN608 ´z+H4¶6j¨ Page 1140206-26 ´z+H4¶6j¨ ´z+H4¶6j¨
Related manuals
Manual 4 pages 16.24 Kb

372XP, 365 specifications

The Husqvarna 365 and 372XP chainsaws are powerful and versatile tools designed for both professional loggers and serious homeowners. Known for their robust construction and reliability, these models offer a perfect blend of performance and user-friendly features.

The Husqvarna 365 is equipped with a 70.7 cc engine that delivers impressive power, making it suitable for demanding cutting tasks. This chainsaw is designed for all-day use, ensuring that operators can tackle large trees and tough woods without losing momentum. The engine utilizes Smart Start technology, which allows for easier starting with minimal effort. This innovation reduces the resistance in the starter cord by up to 40%, enabling rapid and hassle-free ignition.

On the other hand, the Husqvarna 372XP boasts a slightly larger 72.2 cc engine, making it one of the most powerful saws in the market. Specifically tailored for professionals, this chainsaw excels in heavy-duty applications and has the ability to handle extreme workloads. Both models are designed with a high RPM, ensuring smooth cutting performance and efficient chip flow, which contributes to cleaner cuts and enhanced productivity.

A significant feature of these chainsaws is their ergonomic design, which includes a comfortable handle for better grip and control during operation. The chainsaws also feature an adjustable oil pump that allows users to customize the oil flow for the chain and bar, which helps minimize wear and prolongs the lifespan of the saw.

Safety is paramount with both the 365 and 372XP models. They are equipped with a chain brake system that automatically stops the chain in the event of kickback, ensuring user protection. Furthermore, the low vibration technology significantly reduces vibrations experienced by the operator, promoting comfort during prolonged use.

In terms of maintenance, both chainsaws come with a quick-release air filter that makes it easy to access and clean, ensuring optimal engine performance over time. The built-in fuel pump facilitates easier starting after long periods of inactivity, making these tools reliable for various cutting tasks.

In summary, the Husqvarna 365 and 372XP chainsaws stand out for their powerful engines, user-friendly features, and advanced safety technologies. They are engineered to meet the high demands of professional users while also being accessible for those who need a reliable chainsaw for home use. Whether for felling trees or limbing, these models deliver excellence in performance and durability.
Top Page Image Contents