Husqvarna 372XP, 365 manual Directional cuts, Felling cut

Page 21

SAFETY INSTRUCTIONS

Remove any undergrowth from the base of the tree and check the area for obstacles (stones, branches, holes, etc.) so that you have a clear path of retreat when the tree starts to fall.

Your path of retreat should be roughly 135 degrees away from the intended felling direction.

Felling

Felling is done using three cuts. First you make the directional cuts, which consist of the top cut and the bottom cut, then you finish with the felling cut. By placing these cuts correctly you can control the felling direction very accurately.

Directional cuts

To make the directional cuts you begin with the top cut. Stand to the right of the tree and cut on the pull stroke.

Next make the bottom cut so that it finishes exactly at the end of the top cut.

The directional cuts should run 1/4 of the diameter through the trunk and the angle between the top cut and bottom cut should be 45°.

The line where the two cuts meet is called the directional cut line. This line should be perfectly horizontal and at right angles (90°) to the chosen felling direction.

Felling cut

The felling cut is made from the opposite side of the tree and it must be perfectly horizontal. Stand on the left side of the tree and cut on the pull stroke.

Make the felling cut about 3-5 cm (1.5-2 inches) above the bottom directional cut.

Set the spike bumper (if one is fitted) just behind the felling hinge. Use full throttle and advance the chain/bar slowly into the tree. Make sure the tree does not start to move in the opposite direction to your intended felling direction. Drive a wedge or breaking bar into the cut as soon as it is deep enough.

Finish the felling cut parallel with the directional cut line so that the distance between them is at least 1/10 of the trunk diameter. The uncut section of the trunk is called the felling hinge.

The felling hinge controls the direction that the tree falls in.

All control over the felling direction is lost if the felling hinge is too narrow or non-existent, or if the directional cuts and felling cut are badly placed.

When the felling cut and directional cut are complete the tree should start to fall by itself or with the aid of a felling wedge or breaking bar.

English – 21

Image 21
Contents 362XP 365 372XP Key to symbols KEY to SymbolsContents Safety Instructions Machine′s safety equipmentPersonal protective equipment Chain brake and front hand guard Throttle lock Stop switchChain catcher Right hand guardChecking brake band wear MufflerChecking the front hand guard Checking the inertia brake releaseThrottle lock Stop switchChain catcher Right hand guardGeneral rules Cutting equipmentCutting equipment designed to minimise kickback MufflerSome terms that describe the bar and chain ChainGeneral information on sharpening cutting teeth Sharpening your chain and adjusting raker clearanceSharpening cutting teeth With a badly sharpened chainSetting the raker clearance General advice on setting raker clearanceTensioning the chain If the raker clearance is too largeChain oil Lubricating cutting equipmentFilling with chain oil Checking chain lubricationNeedle bearing lubrication Lubricating the bar tip sprocketChecking wear on cutting equipment Chain drive sprocketHow to avoid kickback What is kickback?Do not let go of the handles General safety precautions Fuel safety StartingTransport and storage General working instructions Basic safety rulesBasic cutting technique GeneralCutting TermsLimbing Tree felling techniqueSafe distance Felling directionFelling Directional cutsFelling cut Freeing a tree that has fallen badly General adviceCutting the trunk into logs Freeing a trapped treeWhat is what on the chain saw? What is WHAT?Fitting the bar and chain AssemblyFitting a spike bumper Working with the chainFuel Fuel HandlingMin 3 m 10ft FuellingStarting and stopping Starting and StoppingCold engine Warm engineStopping Carburettor MaintenanceStarter Correctly adjusted carburettorHigh speed jet H Changing a broken or worn starter cordSpark plug Air filterTensioning the recoil spring Changing a broken recoil springWhen making adjustments Adjustment of the oil pumpMuffler Needle bearing lubricationHeated handles Air Injection centrifugal cleaningElectrical carburettor heating Winter useWeekly maintenance Daily maintenanceMonthly maintenance Below you will find some general maintenance instructionsTechnical data Technical DataBar Chain Bar and chain combinationsEC-declaration of conformity Applies to Europe onlyEN292-2, Cispr 121997, EN608 ´z+H4¶6j¨ Page 1140206-26 ´z+H4¶6j¨ ´z+H4¶6j¨
Related manuals
Manual 4 pages 16.24 Kb

372XP, 365 specifications

The Husqvarna 365 and 372XP chainsaws are powerful and versatile tools designed for both professional loggers and serious homeowners. Known for their robust construction and reliability, these models offer a perfect blend of performance and user-friendly features.

The Husqvarna 365 is equipped with a 70.7 cc engine that delivers impressive power, making it suitable for demanding cutting tasks. This chainsaw is designed for all-day use, ensuring that operators can tackle large trees and tough woods without losing momentum. The engine utilizes Smart Start technology, which allows for easier starting with minimal effort. This innovation reduces the resistance in the starter cord by up to 40%, enabling rapid and hassle-free ignition.

On the other hand, the Husqvarna 372XP boasts a slightly larger 72.2 cc engine, making it one of the most powerful saws in the market. Specifically tailored for professionals, this chainsaw excels in heavy-duty applications and has the ability to handle extreme workloads. Both models are designed with a high RPM, ensuring smooth cutting performance and efficient chip flow, which contributes to cleaner cuts and enhanced productivity.

A significant feature of these chainsaws is their ergonomic design, which includes a comfortable handle for better grip and control during operation. The chainsaws also feature an adjustable oil pump that allows users to customize the oil flow for the chain and bar, which helps minimize wear and prolongs the lifespan of the saw.

Safety is paramount with both the 365 and 372XP models. They are equipped with a chain brake system that automatically stops the chain in the event of kickback, ensuring user protection. Furthermore, the low vibration technology significantly reduces vibrations experienced by the operator, promoting comfort during prolonged use.

In terms of maintenance, both chainsaws come with a quick-release air filter that makes it easy to access and clean, ensuring optimal engine performance over time. The built-in fuel pump facilitates easier starting after long periods of inactivity, making these tools reliable for various cutting tasks.

In summary, the Husqvarna 365 and 372XP chainsaws stand out for their powerful engines, user-friendly features, and advanced safety technologies. They are engineered to meet the high demands of professional users while also being accessible for those who need a reliable chainsaw for home use. Whether for felling trees or limbing, these models deliver excellence in performance and durability.